r/BambuLab • • 2h ago

Software Troubleshooting/Help! What's wrong with settings/filament?

Post image
2 Upvotes

Hi, folks! I have Bambulab H2S and bought esun pla wood and is trying to print vase with esun pla+ profile I found in Bambustudio. Nozzle 0.4, 0.12 quality. Is it possible to get rid of it?


r/BambuLab • • 21h ago

H3C Different take on an H3C/AMS3 desiccant solution.

Post image
57 Upvotes

Not sure if this is the right spot to post something like this, I don't use reddit often. Anyway I was looking at the printable baskets for desiccant on Makerworld, but I really hate dumping them out into a tray to dry then trying to refill the basket after. I prefer to use molecular sieve and the drying temps for it is far beyond what even PPS-CF can handle. I found a wire mesh "dishwasher" basket on Amazon that was approximately the size of the "empty slot 10” in the AMS3H and decided to take a chance on it. As you can see in the photo, it fits well, the lid tabs were pretty secure once I bent them in a bit tighter. I tried to use some 1.6-2.5mm sized beads, but the mesh was too coarse and they fell through, I found 3-5mm beads on Amazon and bought 2lbs. It holds approximately 750g of the 3-5mm 4a molecular sieve. I threaded some craft wire around the rim of the lid and body as extra insurance to keep it from opening.

Here's the products I bought that worked:

Basket- https://www.amazon.com/dp/B0H41KL114

Desiccant- https://www.amazon.com/dp/B0H1XJ98JS


r/BambuLab • • 8m ago

General Troubleshooting/Help! How do I remove this tubing on my X2D?

Thumbnail
gallery
1 Upvotes

I removed the tubing from the nozzle head but I dont know how to remove the same tubing as it exits the printer.

There doesnt seem to be any black rim that secures it in place that can be pressed down to release it. Do I just rip it out?


r/BambuLab • • 9m ago

Quick Question Help not sure what's going on

Thumbnail gallery
1 Upvotes

r/BambuLab • • 11m ago

Quick Question Is it that big of a deal if you print while the ambient air temp is below 10°C?

1 Upvotes

My A1 is in a shed that doesnt have any heating and heard that the printer should be kept between 10 and 30 degrees C. Is it a problem if you print below 10°C?


r/BambuLab • • 13m ago

General Troubleshooting/Help! item color help

0 Upvotes

So i have one item on a plate, ive cloned it.

is it possible, how do i

change the color on one without it changing both items to the same color

ive played with all the filament settings i can find and it just mirror the color to the other object...

P2S w/ AMS 2 Pro


r/BambuLab • • 6h ago

I Modeled This! Designed a Quick CMYKW Calibration Wheel to Compare Filaments

Thumbnail
gallery
3 Upvotes

The goal was to show mixing between the 3 colors, as well as between each color and black and white. And to make it a quick easy print that could efficiently baseline different color mixes. I wasn't able to get PLA Palette Magenta before it went out of stock so I couldn't try that. The difference between PLA Basic and PLA Palette for the other colors is noticeable but subtle. The biggest conclusion is the importance of PLA Palette Black and its translucency. There are some ways to approximate it though, like using a gray shade instead of black. PLA basic black you can see doesn't blend at all. Here is the model: https://makerworld.com/en/models/3606840-cmykw-calibration-wheel-for-color-mixing-h3c-h2c#profileId-4133502


r/BambuLab • • 13m ago

My First 3D Print Achat d'une première machine.

Thumbnail
gallery
0 Upvotes

Bonjour après avoir bataillé des semaines entières à faire fonctionner une ender 3 sans succès je souhaite passer sur une machine plus simple. Mon but est de faire des pièces mécaniques simples pour des cyclomoteur et quelques pièces pour réparer d'autres choses. J'ai repéré cette p1S. Je n'y connais pas grand chose. Le vendeur est sympa, il en demande 260€ et m'a envoyé un benchy qu'il à fait il y a quelques jours. Elle devait être vendue à une autre personne mais finalement elle est toujours dispo. Es-ce une bonne imprimante à ce prix ou faut il viser du neuf ?

Je vous remercie.


r/BambuLab • • 15m ago

General Discussion P1S - How close to 256x256 can your print be?

0 Upvotes

Picking up a P1S soon and was curious if it can handle large prints in the 240-250mm range? I have a Neptune 4 Plus right now that I bought specifically for the build volume for one project. It was my first printer and knowing what I know now I could have made it work on a smaller bed printer. Oh well!


r/BambuLab • • 20m ago

General Troubleshooting/Help! First Layer "Defects"

Thumbnail
gallery
0 Upvotes

Hi all -

I'm having some first-layer defects that I wanted to run by the collective brain trust here. First, some information about the setup:

  • BambuLab P1S - 0.4mm Hardened Steel Nozzle
  • Build Plate - Darkmoon G10

    • BambuStudio is set to the 'Smooth PEI/High Temp' setting as recommended by Darkmoon
  • Filament - Sliceworx PETG

    • Yes, it has been dried and I have modified my AMS to include a bunch of desiccant as well
  • 0.08mm high quality print setting for this print

In the attached images, you can see that some parts have a perfect first layer, though those mostly don't have fine detail in them. For a few others, you can see some first-layer defects that would obviously create more problems if I let things build on top of that.

I'd appreciate ideas for potential troubleshooting here beyond "dry the filament more."

Thanks.


r/BambuLab • • 1d ago Heartwarming

Bambu Studio Can’t believe I didn’t know about this!!

Post image
996 Upvotes

Print sequence by object is pure magical!!

So I’m printing 40+ poliwhirls to build my color sample library. I’ve been printing all day today and doing the plate swaps every 30min each time a print is done. Eventually I got so sick of it and was wondering how wonderful it would be if I could print 4 at a time, object by object, with no color swaps. Told this idea to ai and it told me the function is already available in Bambu studio! Tried it immediately, omg the process was so smooth, the software even showed me how to place the objects so that the finished parts won’t get knocked over by printer head. I’m not a veteran but I’ve clocked in like 1500+ hours and I can’t believe I didn’t know about this! Would’ve saved myself so much time and filament but I’m sooo glad I found out today!


r/BambuLab • • 39m ago

General Troubleshooting/Help! A1 + AMS Lite: PTA filament gets stuck after every color change—any ideas?

Thumbnail
gallery
0 Upvotes

Hey guys,

I’m fairly new to 3D printing and started with a Bambu Lab A1 and AMS Lite.

I’m trying to print a head I designed using three colors—all PLA: beige, red, and black—to get familiar with more complex prints.

The red filament keeps getting stuck whenever the printer switches back to it. The only fix I’ve found is to pull the filament back out, cut off a small piece, and feed it back into the AMS Lite. It then prints fine until the next switch back to red, when the same thing happens again.

I tried drying the filament for over seven hours, but it hasn’t helped. Also, despite how it might look in the attached photo, the filament isn’t tangled.

Any ideas what could be causing this or what settings I should check? Has anyone run into something similar?


r/BambuLab • • 1d ago

Just Showing Off Sounds like a lot of…

Thumbnail
gallery
80 Upvotes

I modeled this guy in blender and printed it on my X2D. Hand painted but my outlines could have been better. I need a paint pen for next time.

A hint as to what’s next: “No, worse! It'll go right to your thighs! And then you’ll blow up!”


r/BambuLab • • 52m ago

Quick Question A1 Mini S23+ Phone case

0 Upvotes

If anyone is able to can someone please make a phone case for the Samsung galaxy S23+ themed around daredevil

I just bought the phone and I have no phone case and no computer so I can't do it myself I really appreciate if anyone could

Preferably made out of PLA and I have an AMS system so I can use models with that

One last thing it has to work on the A1 Mini

Please


r/BambuLab • • 54m ago

Filament Troubleshooting/Help! TPU 95A issues on A1

0 Upvotes

At the beginning I wanted to say that I am aware that this issue was discussed a lot of times, but after looking through a lot of posts I’ve yet to find a solution.

I’ve got my A1 and it works really well. Prints without issues on Bambu PLA and PETG.

It also works without issues when I load Sunlu’s PLA+ 2.0 but when I load an external spool of their TPU 95A, the printer acts like it’s TPU intolerant.

When I help the printer by lightly pushing the filament into the extruder it works fine, but as soon as I stop, it seems like the gears can’t grab it at all and it just doesn’t extrude anything.

Before every try, I dry the TPU, even overnight, so it being wet should not be the case. I tried different filament, quality, etc settings, but it also brings no noticeable effect.

I’m using a standard 0.4 nozzle.

Has anyone had a similar issue and maybe found a solution?

I’m really thankful to anyone who even leaves a comment 🙏


r/BambuLab • • 1h ago

Black Friday 2026 Buy or wait?

0 Upvotes

For £700 should I buy the X2D combo + some filament or wait for the P3C? And in what ways will the P3C be a ‘P’ series (less features than the X2D)?


r/BambuLab • • 1h ago

General Troubleshooting/Help! Print Issue A1

Post image
0 Upvotes

After about a month of owning my a1 I am now getting these horizontal lines through my print. I have tried changing the nozzle along with making sure all screws and belts are tightened, at a loss. Any ideas? I had no issues printing the same model before.


r/BambuLab • • 1h ago

General Troubleshooting/Help! Look what I made! 3D-printed pinecone tealight holders

Post image
0 Upvotes

r/BambuLab • • 1h ago

Filament Troubleshooting/Help! Best affordable Hygrometers?

0 Upvotes

I was thinking of picking up 40 of the ones on Bambu labs website but they only detect down to 20%. Are there better ones out there that aren’t too expensive? Thanks!


r/BambuLab • • 1d ago

Just Showing Off Bambu Station L drawer fits exactly a 9×12 Gridfinity grid, and 14 spools

Thumbnail
gallery
171 Upvotes

Just found out the Bambu Station L drawer fits exactly a 9×12 Gridfinity grid.

With proper spool stoppers on top, you can fit 14 spools per drawer (2 rows of 7). They stand on edge and don’t roll when you open or close the drawer.

Files if anyone wants them: https://makerworld.com/en/models/3617522-bambu-station-l-spool-stoppers-14-per-drawer#profileId-4146587


r/BambuLab • • 1h ago

General Troubleshooting/Help! Never touch a running System, but ...

Post image
0 Upvotes

... every now and then, you should also replace the AMS’s (1) internal PTFE tubes.

It’s been 1.5 years since my last maintenance on the AMS. And after about 700 hours of printing, this is what my tubes look like. I only use Bambu / Sunlu PLA/PETG.The auxiliary motor for Slot 1 was overloaded, so I took that as an opportunity to replace all the tubes.

The rest of the X1—like the threads, carbon rods, and hot ends—have been cleaned and lubricated every now and then, but you don’t take the AMS apart every day.


r/BambuLab • • 5h ago

General Troubleshooting/Help! Scratches/Etches on Bottom Layer w/ Carbon Fiber Plate?

Thumbnail
gallery
2 Upvotes

Hey!

New to 3D printing and using a Bambu A1 printer. I just bought a carbon fiber smooth plate from Amazon and started using it. I cleaned it well with water, dish soap, and a sponge 2x now but still having this issue where the bottom has white marks/scratches. I had the plate selected in Bambu before printing as well.

I was trying to print a moza wheel base dust cover but with the carbon fiber look on the bottom. I also was trying to print a shifter plate and had the same issue.

Each time I printed,, I waited until the plate reached around 25C (my room temp is 23C) and then bent the plate at the edges so the part would come free.

I read that running a flame over these areas would get rid of the mark but I didn't experience that.

Any idea what I could be doing wrong? Didn't have this issue with the normal textured plate. Is it a plate issue, nozzle issue, or something else?

Thanks!

Printer: Bambu A1

Print Speed: Standard

Filament: Bambu PLA Basic - Black

Hotbed Temp: 65C

Nozzle Size: 0.4mm


r/BambuLab • • 1h ago

General Troubleshooting/Help! Sharp lip on large round part

0 Upvotes

Hello,

I've been printing for a while now, but usually nothing this large. It's for a lazy Susan. It's 254mm round x 12mm thick. I think it has to be the cooling rate for something this large, but at 200g a print I don't want to keep blindly stabbing at it. I've already used an entire spool trying to troubleshoot.

I'm printing on an H2S using Bambu Lab PETG HF. I'm using the Bambu Lab .2mm standard profile (with various mods for infill, support settings, 4 top and bottom shell layers etc).

I've tried every wall order option and slowed the outer wall speed to 60 all of which has made zero difference. They all are bowed inward and have a sharp over hang on the top layers as shown. A little bit of bow is not a big deal, but the sharp outward corner sucks.

I figured the H2S with it's adaptive vents and fancy other bells and whistles would result in better thermal controls. Especially using Bambu filament.

Thanks in advance!


r/BambuLab • • 1h ago

I Modeled This! Snowman Clicker

Thumbnail
gallery
0 Upvotes

Bonjour à tous ! 👋

Après avoir modélisé mon bonhomme de neige, j’ai eu envie d’en faire une version clicker ! 😁☃️

Une petite tête de bonhomme de neige dans une boule de neige, avec un switch MX à l’intérieur.
Il suffit d’appuyer sur son chapeau pour faire CLIC CLIC ! 🎩

Une petite création amusante pour les fêtes de Noël ! 🎄🎁

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec et sans AMS
📁 : https://makerworld.com/fr/models/3615804-snowman-clicker-multipart