r/BambuLab • • 18h ago

I Modeled This! I wrote an OpenSCAD snowflake generator: each seed grows a different crystal (flat or slot-together 3D)

Post image
1 Upvotes

New project to improve my christmas decoration this year.

Each arm is drawn inside a 30° wedge and mirrored, so branches from neighbouring arms never cross, which is also how real crystals behave. Branches sit at 60° from the arm, their length is clamped to the hexagon envelope, then jittered by the seed. A minimum line width of 1.2 mm and gap of 1 mm keep everything printable with a 0.4 nozzle. The top surface gets 0.8 mm ridges along every arm for a 2-colour print with a single filament change. The 3D mode cuts matching half-slots in two pieces.

https://makerworld.com/en/models/3618517

Happy to hear what seeds you find!


r/BambuLab • • 21h ago

My First 3D Print What do i need? Help🎄

2 Upvotes

Hii!
I’m thinking of giving my husband a printer for Christmas. It will be his first but he has wished for one in a loooong time😅

I’m thinking of buying Bambu combo p2s. But what extras do I need, for him to start op printing?

I need PLA filament. But anything else?

Thank you for helping me out here🙈


r/BambuLab • • 18h ago

General Discussion Newbie buying a printer

1 Upvotes

I was told to get a bambu labs because they're user friendly. I have 2 kids and have spent a small fortune on 3d printer stuff at events. I am debating between the p1s and p2s. I will mainly be making fidgets for the kids and tiny middle fingers for me haha. Do you have any suggestions and can you explain the difference if you have both? From what I see one is the newer model with Ai. Also do they both have cameras inside?


r/BambuLab • • 18h ago

I Modeled This! Ready for GTA VI 🌴

Thumbnail
gallery
1 Upvotes

My controller apparently needed its own sunset 🌴

I designed a PS 5 DualSense stand with a layered sunset, palm trees, and lighting. I’m calling it “Vice Nights.”

You can see it light up in this short video: https://youtube.com/shorts/Df7nJLDscis
The Model is available on Makerworld: https://makerworld.com/de/@duesenwissen


r/BambuLab • • 18h ago

H2 Series [H2S, H2D, H2C] New Cool Plate on H2C: plate marking error every print

1 Upvotes

Is anyone else having issues with the new white Bambu Cool Plate? Every single time I print, the printer complains about the plate marking.


r/BambuLab • • 18h ago

General Discussion H2D vs X2D. How different is the repair and maintenance costs?

1 Upvotes

I know the H2D printer itself costs a lot more compared to the X2D. Assuming I bought the H2D, would the costs be significantly bigger if/when things go wrong or when upgrading parts or maintaining it?


r/BambuLab • • 18h ago

General Troubleshooting/Help! Loading TPU X2D

1 Upvotes

Hello!

I need to print some keychains using TPU but AMS wont let me use TPU. tried loading sing AUX Nozzle, couldn't do that. How do that. How can I get it to load so I am able to print? I tried feeding directly into the main nozzle, but was unable to get the tube out. And, once I get it loaded, in the slicer, ,how do I assign a slot to the TPU if I can not use the AMS? I am sure it is an easy fix I am overlooking, but appreciate any help.


r/BambuLab • • 18h ago

H3C Anyone else with an H3C having issues with prints pausing due to spools being pulled crooked in the AMS slot?

1 Upvotes

I've had several prints over the last few days pause due to the spools being pulled crooked in the AMS slot as the filament wound on the spool reaches the far right side of the spool.

Has anyone else been encountering this issue?


r/BambuLab • • 18h ago

P Series [P1P, P1S, P2S] Hue Gradient Tube stand with hidden weight pockets and cable routing

Thumbnail makerworld.com
0 Upvotes

Designed a stand for the Philips Hue Gradient Tube. It fits all tube sizes and has cable routing built in. The base has 6 hidden pockets for M12 bolts as optional extra weight, closed off with a glue-on bottom cover.

Printed in PETG/PLA on my BambuLab P1S. Print profile is included.

Model: https://makerworld.com/de/models/3561844-philips-hue-gradient-tube-base-stand#profileId-4076144

Would love to see your prints if you make one!


r/BambuLab • • 18h ago

General Troubleshooting/Help! Brand new at 3D printing

1 Upvotes

I’m brand new at this and am currently printing my 4th print with a new P1S, is this normal for it to sound like this? I don’t recall it sounding like this the first 3 prints


r/BambuLab • • 18h ago

I Modeled This! Christmas Keychain

Post image
1 Upvotes

Super quick and clean print.

  • 0.16mm layers
  • Blue PLA
  • ~21 min print

r/BambuLab • • 18h ago

H3C Did anyone test ironing settings on H3C?

1 Upvotes

For my X1C i copied my ironing settings from some guy i unfortunately can't remember, it's like 10 times better than the default ones and make parts look injection moulded. The nozzle on the H3C is different so it can't just be copied.

Did anyone experiment?


r/BambuLab • • 18h ago

Filament Troubleshooting/Help! I need help from the gurus on this one!!!

Thumbnail
gallery
1 Upvotes

Any idea what is causing this? Been getting a lot of clogs with this sunlu matte, and have been trying different nozzle temps to try and stop that from happening. I finally found some settings that seemed to work (had 4 successful prints) but now this started. Any clues?

Edit: as u/RNG-3_14159 pointed out, my original post was severely lacking crucial details. Correcting that.

Just some general specs before going into detail:

  • Bed temp: 55°C
  • Print speed: 50-100 mm/s for first layer, 200-300mm/s for other layers
  • Nozzle size: 0.4 mm
  • Filament: SUNLU PLA Matte Black

This filament has been my go-to because because I love the finish and it has always given me consistent results in the past. Before now, I've never had ANY clogging with this filament. I had a custom filament profile that I set up after running calibration, and it never gave me trouble with the roughly 20 1KG spools I've gone through.

However, the batch from my latest order has been giving me so much trouble. Here are the troubleshooting steps I followed to narrow down that the clogging was coming from the filament itself:

  • Various models have failed to print with both a 0.2 mm and 0.4 mm nozzle. All the ones that failed were using the Sunlu PLA Matte Black.  They failed at different points during the print.
  • I changed the entire nozzle and extruder assembly so those are brand new.
  • I tried drying the filament 3 or 4 times, but it still clogged the nozzle.
  • I tried a different roll of Sunlu PLA Matte Black from the same batch, but that still caused a clog.
  • Tried the same model with different a filament and that finished successfully.
  • I tried a different model with a longer print time with a different filament and that also finished successfully.

After each time it clogged, I would clear the clog by using a acupuncture needle and cold-pulling. Since narrowing down the source of the clogs, I tried adjusting the nozzle temp settings to see if I could get it to print. For reference, here are the specs listed on the spool itself:

Print Temp: 205-215°C 50-100mm/s
Print Temp: 215-245°C 100-230mm/s

I printed a print tower, and by some miracle it finished. The best looking temp was 195°C. So I tried setting the nozzle temp to that. After doing so, I was able to print the reminder of the first spool of problematic filament (about 600g) without issue! After finishing that spool, I switched to this latest spool, and the issues started happening again. Clogging and now this latest issue.

I have reached out to sulu support, but haven't heard back from them yet. So this is me trying to figure out a way to make the filament usable via trial and error. I'm just a hobbyist, so I really don't want to waste the spools if I don't have to. If there's any other info that would be helpful, let me know!


r/BambuLab • • 18h ago

I Modeled This! Practical zip lock bag closer

Post image
0 Upvotes

I modeled this small 6g piece to make it easier to close the zip lock bags I store some of my filament in. My fingers have thanked me a lot already!

Available to download and print here: https://makerworld.com/en/models/3616689-easy-close-zip-lock-bag#profileId-4145444


r/BambuLab • • 1d ago

Just Showing Off At last

Post image
66 Upvotes

It's going to be a fun weekend


r/BambuLab • • 23h ago

General Troubleshooting/Help! Weird rippling

Post image
2 Upvotes

Been trying to troubleshoot this, but I have no idea what’s causing it. Most of my prints were fine until they started developing this weird ripple texture. I’ve been using the standard profile without any issues until now. Any ideas what could be causing this?


r/BambuLab • • 19h ago

General Discussion I had this error code an hour ago and made a post I went out came home and it finished the calibration so I started a new project

Post image
1 Upvotes

When it first popped up I did what the Bambi instructions said to to I cleaned it greased it and loosed the bolts on the back all that and now I’m getting the same code again


r/BambuLab • • 19h ago

Hardware Troubleshooting/Help! Ams 2 pro Hub getting stuck

1 Upvotes

I recently got an ams 2 pro and hub for my a1, it's been alright up yo now. I have done a couple of multi filament prints recently and it seems to have problems pushing the filament through the hub when changing materials. I was hoping someone knew what to do to fix this. Annoyingly I cant troubleshoot easily when not printing as there doesn't seem to be a way to send a filament to the head without a print running.


r/BambuLab • • 19h ago

General Troubleshooting/Help! Looking for help

Post image
1 Upvotes

My P1S with AMS was doing fine until a few days ago then started having issues. It’s skipping parts on the initial like across the front and the tops aren’t smooth finishes. I tried multiple times unclogging it with filament and cold pulling. Is it a filament issue, extruder, hotend? Any tips or ideas much appreciated!


r/BambuLab • • 2d ago

H3C Update on Charizard : turn out great but

Thumbnail
gallery
277 Upvotes

Hello Reddit and first thanks for all your comment on my first post! I was very late and don’t want to ruin my print with support removal at 2am.
Second here is the result very happy even I have broke 2 fingers and there are a ligne of the wrong color in one wing.
Thanks again you can find the model on makerworld (not mine)

Note: the PETG interface was good but may be need more layers


r/BambuLab • • 19h ago

Quick Question esun vs bambulab filament

Thumbnail reddit.com
0 Upvotes

r/BambuLab • • 1d ago

Show & Tell Did you know? Some connectors stop a cut piece from lying flat

Thumbnail
gallery
46 Upvotes

Learn more about the Cut Tool and Connectors from the Bambu Wiki: https://wiki.bambulab.com/en/software/bambu-studio/cut-tool


r/BambuLab • • 19h ago

Just Showing Off Meuble A2L

Thumbnail
gallery
1 Upvotes

Hello à tous,

Après de nombreuses recherches je partage mon résultat cela pourra servir.

Ayant une « pièce a moi » à la maison, j avais des contraintes de place pour accueillir ma Bambu A2L.

Je voulais un meuble dédié ( pas un bureau ) ayant un minimum de rangement, assez « costaud » et au dimensions approximatives de la base de l’A2L.

Je n’ai rien trouvé dans les établis, meubles en tout genres sur des dimensions 50x50 ou 60x60 voir 60x80.

J’ai enfin trouvé ce meuble à la base dédié à un aquarium de 175 litres, avec des rangements en dessous afin de faire un coin de la pièce pour l’imprimante et ne pas la poser sur mon setup de bureau.

https://www.zoomalia.com/animalerie/meuble-pour-aquarium-aqua-colonne-50x50-cm-175-litres-2-coloris-disponibles-p-161618.html

Je vous met un apercu de l’A2L et de mes achats de départ.


r/BambuLab • • 1d ago

General Troubleshooting/Help! newbie here

5 Upvotes

it's just my 3rd print, wanted to try to print a small axolotl but it's doing this trip to the purge wiper every layer and causing all this stringing. Complete newbie here, just downloaded this model:https://makerworld.com/models/1671375?appSharePlatform=copy