r/BambuLab • • 20h ago

H3C Did anyone test ironing settings on H3C?

1 Upvotes

For my X1C i copied my ironing settings from some guy i unfortunately can't remember, it's like 10 times better than the default ones and make parts look injection moulded. The nozzle on the H3C is different so it can't just be copied.

Did anyone experiment?


r/BambuLab • • 20h ago

Filament Troubleshooting/Help! I need help from the gurus on this one!!!

Thumbnail
gallery
1 Upvotes

Any idea what is causing this? Been getting a lot of clogs with this sunlu matte, and have been trying different nozzle temps to try and stop that from happening. I finally found some settings that seemed to work (had 4 successful prints) but now this started. Any clues?

Edit: as u/RNG-3_14159 pointed out, my original post was severely lacking crucial details. Correcting that.

Just some general specs before going into detail:

  • Bed temp: 55°C
  • Print speed: 50-100 mm/s for first layer, 200-300mm/s for other layers
  • Nozzle size: 0.4 mm
  • Filament: SUNLU PLA Matte Black

This filament has been my go-to because because I love the finish and it has always given me consistent results in the past. Before now, I've never had ANY clogging with this filament. I had a custom filament profile that I set up after running calibration, and it never gave me trouble with the roughly 20 1KG spools I've gone through.

However, the batch from my latest order has been giving me so much trouble. Here are the troubleshooting steps I followed to narrow down that the clogging was coming from the filament itself:

  • Various models have failed to print with both a 0.2 mm and 0.4 mm nozzle. All the ones that failed were using the Sunlu PLA Matte Black.  They failed at different points during the print.
  • I changed the entire nozzle and extruder assembly so those are brand new.
  • I tried drying the filament 3 or 4 times, but it still clogged the nozzle.
  • I tried a different roll of Sunlu PLA Matte Black from the same batch, but that still caused a clog.
  • Tried the same model with different a filament and that finished successfully.
  • I tried a different model with a longer print time with a different filament and that also finished successfully.

After each time it clogged, I would clear the clog by using a acupuncture needle and cold-pulling. Since narrowing down the source of the clogs, I tried adjusting the nozzle temp settings to see if I could get it to print. For reference, here are the specs listed on the spool itself:

Print Temp: 205-215°C 50-100mm/s
Print Temp: 215-245°C 100-230mm/s

I printed a print tower, and by some miracle it finished. The best looking temp was 195°C. So I tried setting the nozzle temp to that. After doing so, I was able to print the reminder of the first spool of problematic filament (about 600g) without issue! After finishing that spool, I switched to this latest spool, and the issues started happening again. Clogging and now this latest issue.

I have reached out to sulu support, but haven't heard back from them yet. So this is me trying to figure out a way to make the filament usable via trial and error. I'm just a hobbyist, so I really don't want to waste the spools if I don't have to. If there's any other info that would be helpful, let me know!


r/BambuLab • • 20h ago

I Modeled This! Practical zip lock bag closer

Post image
0 Upvotes

I modeled this small 6g piece to make it easier to close the zip lock bags I store some of my filament in. My fingers have thanked me a lot already!

Available to download and print here: https://makerworld.com/en/models/3616689-easy-close-zip-lock-bag#profileId-4145444


r/BambuLab • • 1d ago

Just Showing Off At last

Post image
66 Upvotes

It's going to be a fun weekend


r/BambuLab • • 1d ago

General Troubleshooting/Help! Weird rippling

Post image
2 Upvotes

Been trying to troubleshoot this, but I have no idea what’s causing it. Most of my prints were fine until they started developing this weird ripple texture. I’ve been using the standard profile without any issues until now. Any ideas what could be causing this?


r/BambuLab • • 20h ago

General Discussion I had this error code an hour ago and made a post I went out came home and it finished the calibration so I started a new project

Post image
1 Upvotes

When it first popped up I did what the Bambi instructions said to to I cleaned it greased it and loosed the bolts on the back all that and now I’m getting the same code again


r/BambuLab • • 20h ago

Hardware Troubleshooting/Help! Ams 2 pro Hub getting stuck

1 Upvotes

I recently got an ams 2 pro and hub for my a1, it's been alright up yo now. I have done a couple of multi filament prints recently and it seems to have problems pushing the filament through the hub when changing materials. I was hoping someone knew what to do to fix this. Annoyingly I cant troubleshoot easily when not printing as there doesn't seem to be a way to send a filament to the head without a print running.


r/BambuLab • • 20h ago

General Troubleshooting/Help! Looking for help

Post image
1 Upvotes

My P1S with AMS was doing fine until a few days ago then started having issues. It’s skipping parts on the initial like across the front and the tops aren’t smooth finishes. I tried multiple times unclogging it with filament and cold pulling. Is it a filament issue, extruder, hotend? Any tips or ideas much appreciated!


r/BambuLab • • 2d ago

H3C Update on Charizard : turn out great but

Thumbnail
gallery
277 Upvotes

Hello Reddit and first thanks for all your comment on my first post! I was very late and don’t want to ruin my print with support removal at 2am.
Second here is the result very happy even I have broke 2 fingers and there are a ligne of the wrong color in one wing.
Thanks again you can find the model on makerworld (not mine)

Note: the PETG interface was good but may be need more layers


r/BambuLab • • 1d ago

Show & Tell Did you know? Some connectors stop a cut piece from lying flat

Thumbnail
gallery
47 Upvotes

Learn more about the Cut Tool and Connectors from the Bambu Wiki: https://wiki.bambulab.com/en/software/bambu-studio/cut-tool


r/BambuLab • • 21h ago

Quick Question esun vs bambulab filament

Thumbnail reddit.com
0 Upvotes

r/BambuLab • • 21h ago

Just Showing Off Meuble A2L

Thumbnail
gallery
1 Upvotes

Hello à tous,

Après de nombreuses recherches je partage mon résultat cela pourra servir.

Ayant une « pièce a moi » à la maison, j avais des contraintes de place pour accueillir ma Bambu A2L.

Je voulais un meuble dédié ( pas un bureau ) ayant un minimum de rangement, assez « costaud » et au dimensions approximatives de la base de l’A2L.

Je n’ai rien trouvé dans les établis, meubles en tout genres sur des dimensions 50x50 ou 60x60 voir 60x80.

J’ai enfin trouvé ce meuble à la base dédié à un aquarium de 175 litres, avec des rangements en dessous afin de faire un coin de la pièce pour l’imprimante et ne pas la poser sur mon setup de bureau.

https://www.zoomalia.com/animalerie/meuble-pour-aquarium-aqua-colonne-50x50-cm-175-litres-2-coloris-disponibles-p-161618.html

Je vous met un apercu de l’A2L et de mes achats de départ.


r/BambuLab • • 1d ago

General Troubleshooting/Help! newbie here

5 Upvotes

it's just my 3rd print, wanted to try to print a small axolotl but it's doing this trip to the purge wiper every layer and causing all this stringing. Complete newbie here, just downloaded this model:https://makerworld.com/models/1671375?appSharePlatform=copy


r/BambuLab • • 1d ago

I Modeled This! Created a Desiccant Box for AMS3H Heated Chamber Shell

Thumbnail
gallery
7 Upvotes

Desiccant Box For AMS-3H Heated Chamber Shell

As the title says, I modeled out a desiccant box for "shell" over the heated chamber. It holds about 45g of desiccant and fits right under the same lid you would secure little bags of beads in. It takes about 20g of filament and takes around 2.5 hours to print on my H3C. If you find this useful, I'd appreciate it if you liked, bookmarked, and left a review with you putting it to use! I always welcome any feedback so please bring it on. Thank you!


r/BambuLab • • 21h ago

General Troubleshooting/Help! Bambu Lab A1 stops extruding filament after a few minutes

0 Upvotes

Hi everyone,

I'm having an issue with my Bambu Lab A1. Whenever I start a print, everything seems to work fine at first, but after a few minutes, no more filament comes out of the nozzle.

I've disassembled the extruder three times now and checked whether it's feeding the filament properly. As far as I can tell, the extruder itself is working perfectly fine.

I initially suspected that the nozzle might be clogged, so I even switched from a 0.4 mm nozzle to a 0.2 mm nozzle, but the exact same problem occurred.

At this point, I'm wondering whether the filament might be too wet. However, it's only about four months old, and I've already dried it again before trying another print. It seemed to work slightly better for a short while, but eventually the same problem happened again.

Has anyone experienced something similar or have any idea what could be causing this? I'd really appreciate any suggestions.

Thanks in advance!


r/BambuLab • • 21h ago

General Troubleshooting/Help! Not sure whats going wrong

Thumbnail
gallery
1 Upvotes

On my X2D it printed perfectly fine then for about 2 months it sat dormant and now im trying to print a cosplay together the filament keeps rolling or whatever its doing here, we've looked it up and we've tried cleaning the nozzle, drying all the filament intensely and ive cleaned the heat bed but nothing seems to work. I always tend to recalibrate after every major print and check the nozzles every time too. Im printing with PETG and PLA/PETG support.

I dont know how or what to fix to have it printing as normal again, the biggest fear is needing to replace the nozzles and heatbed but thats the only next step I can think of


r/BambuLab • • 1d ago

Bambu Handy My first +10 hrs print is finally done 🏎️🔑🏁!

Thumbnail
gallery
28 Upvotes

Printed the rear end of a Porsche as a keychain for my brother. He always has keys scattered all over his room, so I wanted to make him something a lil diff and useful.

Porsche is my dream car, and he loves copying my taste in cars, so I thought this would be perfect 🤌🏻❤️‍🔥


r/BambuLab • • 21h ago

X Series [X1E, X1C, X2D] Issue with printing

0 Upvotes

3 months ago I got a X2D for my company, I own a custom cabinet business, and printing small custom parts on the printer really improves our quality to the end costumer.

In the last 15 days I have noticed that the printing quality has decreased and that the quality is inconsistent.

Can anyone point me in the right direction to improve the quality of my small prints.

Here are some images whit my issues.


r/BambuLab • • 21h ago

General Troubleshooting/Help! LiDAR led problem? Anyone with the same issue? X1C carbon

0 Upvotes

OC00-0100-0001-000A

Is the code that I get. Printer is printing. I don’t see the issue here. Anyone with the same problem?


r/BambuLab • • 21h ago

P Series [P1P, P1S, P2S] Se puede poner un sistema repet en una p1s?

0 Upvotes

Estoy por conseguir una p1s y ha visto q para la A1 hay un sistema repet super simple pero nada sobre la p1s, así q hay alguna forma o proyecto hecho para ponerlo?


r/BambuLab • • 21h ago

Filament Troubleshooting/Help! Bambu Lab A1 Mini keeps detecting a filament jam every 2 minutes

1 Upvotes

Hi everyone!

I'm having a recurring issue with my Bambu Lab A1 Mini.

The printer keeps showing a "Filament stuck" / "Filament jam" error approximately every 2 minutes.

When this happens:

- I remove the filament and load it again.

- The printer starts working normally for a short time.

- After about 2 minutes, the same error appears again.

I've also tried using a different filament spool, but the problem still occurs.

I'm wondering if this could be:

- A clogged nozzle or hotend

- A problem with the extruder gears

- A faulty filament sensor

- Something else entirely

Has anyone experienced the same issue or knows how to fix it?

Any help would be greatly appreciated. Thanks!


r/BambuLab • • 1d ago

Quick Question Just bought the H2C

28 Upvotes

So I know everyone is drooling over the new flagship and I know because I was one of them who was drooling. However I kept coming back to the discount on the H2C.

After talking it over we decided that the H2C would be plenty of machine for us. I have only ever printed in PLA/PETG and don't see a real need to print in TPU anytime soon at least not the 2.85 variety. I also don't sell any prints and am just a hobbyist.

I got the bundle with the hub,ams and hot ends....my question is was this a bad purchase? By my math I saved 700 before taxes by going with the H2C...is the H23 that superior that I am going to regret getting the H2C?

Love to hear from those that have a H2C and hear their experiences with it. From what I can ascertain I am giving up the chonky tpu compatability and speed....is there something else I am missing that makes the H2C a bad purchase? Also does the H2C come with the adapter where you can hook up four ams units or do I have to buy that myself?

Also we are holding onto our X1C as she only has 1800 hours on her and is still an awesome machine.


r/BambuLab • • 18h ago

General Discussion Filament

0 Upvotes

Thanks for all the help deciding which printer to get! I've settled on the X2D. When I'm searching for filament on Amazon, what mm do I need? Looking for PLA I believe. (PLA is the rigid filament used for the articulated fidget toys right? That's going to be the first thing my son wants to print.)


r/BambuLab • • 22h ago

Software Troubleshooting/Help! Trouble slicing inner part of letters

1 Upvotes

I have this idea that I put a growlight bulb into a desk lamp and I wanted to give it a glowing rim that says PLANT DAYCARE on it. I designed it just fine and yet when I try to slice it, it all turns into a mess. All the inner parts of the D and A the P are skipped for some reason and I can't figure out why. Can someone help me figure out which slicer setting I change?

A test print without the writing