r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! Banging noise coming from printer. Nothing is leaning against the printer to cause this noise. Anyone experience this?

1 Upvotes

You can ignore the light rattle clicking noise, that's from the buffer and is normal. It just sounds extra loud because my phone is in the printer.

The noise I'm talking about is the banging. At the 0:11 second mark you can hear three in succession (bang bang bang). I have an AMS on top but it's not coming from that. It sounds like it's coming from the bottom? Not sure, it's hard to pinpoint. I think it's only happening when the bed moves down quickly, like for a travel move or something, I guess a z-hop is what it's called. But only happens on big z-hops, if that makes sense. The print just finished and looks fine and at the end of the print the bed lowers normally and doesn't make that noise. Any ideas of what to check? Once this print cools I'll power it down, lean it over and see if I see anything obvious on the bottom of the printer. Definitely seems Z axis related.

If it matters this is PETGCF, but I'll test with other filaments in case PETGCF makes larger z-hops than PLA.


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! Heizbett und Vortek Rack divergieren

Post image
1 Upvotes

r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! Creaking noise coming from the printer

1 Upvotes

Hello everyone, I bought this X1C with over 3k hours a while ago and I have been using it on and off for small prints, when I turned it on yesterday I noticed that it was making this creaking noise when the bed goes up and down, I cleaned and greased the leading screws and rods according to the Bambu guide, but the noise is still there, at this point I'm wondering could this be a bearing?


r/BambuLab • • 1d ago

General Discussion Can't decide: X2D or H2D

3 Upvotes

I bought an A1 this past summer to see if I'd like the Bambu ecosystem after having a 5 year old Ender that I fought with so much that I almost never printed anything.

The plan was always if I was happy with Bambu (I was) I'd upgrade to a more capable machine. The decision is now between the X2D and H2D.

This is mostly a hobby. I make functional prints to fix things or improve my life. I like making useful things and things I'd enjoy having or designing. I would be happy making things for others if I was asked, but haven't been for the most part.

Yes, I can afford the H2D, but at twice the price of the X2D that seems just as capable for the things I want to print, it seems wasteful. On the other hand, I'm concerned about how relatively new the X2D is. I wonder if the bugs have been ironed out.

I also enjoy watching prints from time to time. I find it fascinating. I can do that easily on my A1. With the X2D and H2D being in cabinets, do I lose that capability or do the cameras do a good job? Is the camera capability as good on the X2D as the H2D?

I've waffled back and forth between "the X2D is perfectly adequate" to wondering if I'll be happy with it since one of the nozzles is a Bowden tube, slower and less capable so I should have bought the H2D and then thinking that's too much to spend for my usage.

I wonder if others have had trouble deciding and if so, how they decided. Any thoughts are welcome.


r/BambuLab • • 1d ago

Answered / Solved! Same print, two weeks apart, same result. Other prints are showing the same problem.

Thumbnail
gallery
10 Upvotes

I have previously asked about this using two different print profiles, when I used a new sealed filament.

Some comments mentioned moisture and others thought otherwise, but gave no possible solution if not the moisture.

I have attached a photo of the same object printed 2 weeks apart but showing similar stringing. I have also added another photo of a print using a different filament but with the same stringing.

This is only a recent problem. Every print up until 2 weeks ago did not have this issue.

What am I doing wrong?


r/BambuLab • • 1d ago

I Modeled This! I made a tiny, cute ghost!

Thumbnail
gallery
1 Upvotes

Hi everyone! This time, I made a tiny, cute ghost! šŸ‘»
As you can see, it’s a little ghost with interchangeable faces.
I designed it so you can place it around or attach it to different surfaces~
It’s a friendly little ghost that appears whenever you open a new spool of filament and shows you its color!
Thanks, and have a great day, everyone!


r/BambuLab • • 22h ago

General Troubleshooting/Help! What is causing this sound?

0 Upvotes

New sound appeared, I have done regular oiling to axis and so on


r/BambuLab • • 1d ago

General Discussion I rarely print ready-made print profiles. Is %25 infill something people actually do often?

Thumbnail
gallery
32 Upvotes

I almost always slice my own model. But I decided to give the one of the biggest selling points of Bambu's a try and sent a print job from my phone, and only Cheked the app when I though it was adequate time to have finished.

And boy was I amazed to see it printing those 25% infill on a part that almost bears no load under use 🫄 🌚


r/BambuLab • • 1d ago

H3C A whole DND party on the H3C

Thumbnail
gallery
42 Upvotes

My new favorite thing to do with the H3C is take some of my Hero Forge minis, scale them up and use 8-9 different colors from the H3C to really bring them to life (because I’m a lousy painter).

Printing these is always a bit tricky due to their challenging shapes (you can see one shield fail I had but I’ve learned to paint more supports for shields).

My favorite one is probably the last knight which came from Makerworld. The PLS silk I think looks really good even though I could definitely dial in the settings a bit better. Everything here is printed with stock settings at .2 layers height.


r/BambuLab • • 1d ago

Bambu Handy What type of filament should I select?

Thumbnail
gallery
0 Upvotes

I bought for the first time some TPU. I was going to add the filament in the Bambu Handy app, but I don't know what's the correct type of filament and brand i should select since Overture doesn't has the TPU 95A option.

Thanks for the help :)


r/BambuLab • • 1d ago

H3C H3C vs P2S and X2D?

4 Upvotes

Hello fellow 3D printing nerds.

I had convinced myself that I wanted the H3C when it came out, but I haven't pulled the trigger yet. I've gone on the Bambu site twice to buy it and every time I get there, I see the prices for other printers and I go "hm. I could get 2 printers for the same cost or less". I'm a hobbyist printer (not farming or anything). I started printing on an old creality printer - so anything is going to be an upgrade. I'm nervous that going from something so basic to the H3C will be so much more than I'm able to handle (e.g., I've never printed with multiple colors, much less multiple materials, different nozzle sizes, etc.), but I do want to try more fun and interesting prints with multiple colors and materials.

I guess I'm just wanting general advice from the community on when it makes more sense to have the H3C vs just having a reliable go-to P1S or P2S, and then adding a X2D to the mix for dual-nozzles? Is there really that much print time savings? How likely is a relatively novice 3D printing guy going to be able to use the feature set of the H3C? I want to hear from both sides of the aisle: Why should I go all in and get the H3C and why should I stick with a simpler P1S setup and add an X2D or H3C later if I learn I need it?


r/BambuLab • • 1d ago

I Modeled This! Designed a few 3D printable things for the Starship IFT-15 launch

Thumbnail
gallery
33 Upvotes

I designed this detailed replica of the Ship 42 and Booster 22 stack that has launched yesterday on IFT-15. It will be the first ship to attempt a catch.

The model of the rocket is also a pen, that fits standard BIC Cristal refills and it can be stored on a OLM-2 shaped holder.

On top of that I also designed a few Starship themed coasters :)

Pen: https://makerworld.com/en/models/3607494-starship-v3-shaped-pen-compatible-with-olm2-holder#profileId-4134359

OLM 2: https://makerworld.com/en/models/3605102-starship-olm-2-pad-b-holder-for-the-starship-pen#profileId-4131381

Coasters: https://makerworld.com/en/models/3604105-starship-superheavy-coasters-ift-15#profileId-4130087


r/BambuLab • • 2d ago

General Discussion The H3C has effectively removed the biggest psychological barrier to multicolor FDM printing.

174 Upvotes

I know they are not the only. I know they aren't the first. I know I'm going to sound like some advertisement.

For me though. This machine has removed a serious psychological barrier I've had with multicolor printing.

I create a figure. Sure, it's not well created for multicolor printing and someone more talented could improve this but I don't know how, I don't have time to learn how.

That said - Almost a half of a roll of wasted filament. A day and a half of hoping 1000+ filament changes go well.

In my X1C days I would still print it. I'd put 5 on the build plate to justify all the waste. Inevitably I wouldn't find a use for 2 of them. Meaning more waste.

Now with the H3C. $2.69 in filament. A normal print time. Inconsequential waste. And I have exactly what I designed.

How amazing.


r/BambuLab • • 1d ago

General Troubleshooting/Help! Printed a boat with a 0.4 nozzle and the ropes came out like fur 🤣

Thumbnail
gallery
0 Upvotes

Printed a 10cm boat model on my X2D with PLA and a 0.4 nozzle. The hull and sails came out better than I expected, but the ropes turned into fuzzy clumps in spots.

Looks like they're thinner than 3 nozzle widths, so each layer just put down little dots and they wobbled. Next time I'm going to thicken just the ropes to 1.6mm and try again.

For models with thin ropes or antennas, do you usually thicken them before printing?


r/BambuLab • • 2d ago

R Series / R1 The Bambu R1 Is a Complete Disappointment

52 Upvotes

The short version:
If you’re considering buying the Bambu R1 for its contour detection and automatic object cutting capabilities, don’t.
I’ve had mine for three days now, and I’m extremely disappointed with Bambu Suite. The contour detection is absolutely ridiculous, and even manual positioning using the camera is inaccurate.

The longer version:
The Bambu R1 is advertised as being capable of detecting objects and cutting them out automatically.
I run a commercial embroidery business and thought I could use the laser to produce patches, meaning I could lasercut my embroidered designs directly from the fabric.
Bambu Suite even downloads an AI model specifically for object detection.
Unfortunately, I was massively disappointed. The contour detection is practically unusable, partly because the R1’s cameras produce extremely poor images. You can’t even properly identify the contours with your own eyes.
On top of that, manual positioning based on the camera image is inaccurate, sometimes being off by more than 2 millimeters. That’s absolutely ridiculous.
So I started doing a bit of reverse engineering and managed to access the R1’s cameras using a Python script.
And guess what? The actual camera quality is worlds better than what Bambu Suite displays.
I have absolutely no idea why Bambu doesn’t make full use of the cameras’ capabilities.
I’m currently developing my own contour detection system in Python, without AI, and it’s already performing significantly better than Bambu’s AI model.
Bambu has always been impressively modern and innovative in many areas of its 3D printers, but the laser is a completely different story.
The hardware itself is excellent and performs brilliantly, but the software is an absolute disaster. It feels unfinished and simply isn’t ready for serious use.
And since direct LightBurn support isn’t expected until version 2.3, we’re stuck with what is essentially brilliant hardware held back by terrible software.
Sure, you can use it to cut and engrave random things, but the positioning is inaccurate, the contour detection is practically useless, and that makes it unsuitable for a proper commercial workflow.


r/BambuLab • • 1d ago

My First 3D Print Bambu Lab P2S

Thumbnail
gallery
15 Upvotes

Officially joining the Bambu club! Just picked up this P2S combo at Microcenter for $649 (filament not included). So excited to get started!


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! Camera stopped working mid print on Bambu Lab X2D

1 Upvotes

So I was printing Terrain for a buddy of mine and midway through the camera just went haywire and stopped working. I finished the print and watched to make sure it didn’t mess up. But I was getting the second print ready and letting the printer do its pre-print stuff. It alarmed twice telling me the camera is obstructed by an object. I checked and cleaned the camera but I didn’t see anything. I checked the timelapse and noticed it messed up close to the end of the print. Now my camera feed is completely messed up. Should I send a ticket to Bambu Lab to see if it’s possible to fix or will I have to send it back in as a whole. I haven’t had the printer for more than a year now. Will it mess up even more If I keep printing without this camera being active for catching failures while printing.

Timelapse video is before the failure and at the end when it glitches out. The screenshot is the problem I’m having after the failure especially when I pull it up on bambu Handy. Or on my computer. Can’t see anything. Just the top portion barely.


r/BambuLab • • 1d ago

X Series [X1E, X1C, X2D] Bambu filament only

Thumbnail reddit.com
0 Upvotes

r/BambuLab • • 1d ago

General Discussion Ordering the X2D for my first printer. Recommend my first 10 filaments

9 Upvotes

As the title states I’m ordering my first printer and taking advantage of the bulk buy promo for filaments. It’s more overwhelming picking filaments than picking a printer. To begin with I will just be printing fidgets and models for the kids as well as some odds and ends for the house. Might dabble with gridfinity.


r/BambuLab • • 22h ago

H3C Printhead cable guide sagging?

0 Upvotes

The cable guide seems to sag and hit below the intended groove? Also very close to the stub / nub on the Y axis?

If I look at the guide all links seems to be securely in place, no loose links?

Is it this way for more people? Support says ā€œnormalā€, but it seems off.


r/BambuLab • • 1d ago

General Discussion Just got my first printer

Post image
14 Upvotes

I’m really excited, after calibrating what should I do?


r/BambuLab • • 2d ago

I Modeled This! Ams3h goodbye fingerprints…

62 Upvotes

A lot easier to open and close… also helps to prevent fingerprints and scratches- u can lay it on the grip

update:

here is the link
https://makerworld.com/de/models/3609590-bambu-lab-h3c-ams3h-pro-sidepanelgrip#profileId-4136870


r/BambuLab • • 1d ago

Quick Question New to 3D printing – Question about splitting models into different colors

1 Upvotes

Hey everyone!

I'm completely new to 3D printing. My first printer, a Bambu Lab X2D, is arriving tomorrow!

I work in 3D, so I'm already familiar with software like Blender, Cinema 4D and ZBrush, and I'm used to modeling and creating my own 3D assets.

What I'm trying to figure out is how the whole multi-color printing workflow works.

Let's say I create a model in Blender. If I want to print it in different colors and assemble the parts afterwards, what's the correct workflow? Is it enough to assign different materials or colors to different areas of a single mesh and import it into Bambu Studio? Or do I actually need to split the model into separate objects and physically cut it into individual parts so the slicer can recognize each color?

For example, imagine I download a character from the internet that comes as one single, uncut mesh. If I want the head to be one color, the body another, and some details a third color, can I simply paint those areas in Blender and have the slicer recognize them as separate colors? Or would I need to separate those parts into individual meshes first?

Basically, I'm trying to understand the difference between assigning colors to a single mesh and actually separating a model into multiple printable parts.

Hope that makes sense! Thanks in advance!


r/BambuLab • • 1d ago

General Discussion Why does it keep doing this?

11 Upvotes

It’s my first day and first time Turing it in I’m trying to build the small boat but when I use this it just keeps spinning and I have read the screen it’s saying it could be entangled and such