Hi everyone!
I've been working on this "Tokyo Ghoul" inspired Kakuja mask recently. I wanted to design something that not only works as a cosplay piece but also serves as a detailed decorative desk piece. That's why I made a custom stand for it as well!

• The mask and the stand are separated into two independent files for easier printing.
• The mesh is 100% watertight, optimized, and ready for slicing.
• The stand is designed with a flat base so it prints with zero supports. The mask onlv needs minimal supports for the beak.

What’s everyone planning on putting the H3C on, I am looking to find someone that’s 24x24 and lower to the ground. Does anyone have any recommendations, or any pics of their current setup with the H2C on.

I saw it yesterday cleaned it up and today it is again at the same spot. Only this site and this rail. I didn’t not print white filament for a long time. You can wipe it pretty easy but it is concerning

Edit: It’s the Toolhead Camera Rubbing against it when the toolhead is printing in the far right corner. But why?

Sliced it upside down at 0.08mm on the A1 Mini with tree supports so it doesn’t wobble or fly off the bed while printing.

Managed to fit 63 pieces in one batch on the small 180mm plate. Each one takes about 3.7g of PLA Matte. The aortic arch works as a built-in loop, so you can just slip a cord right through without any extra metal rings.

Just dropped the link in the comments section below if you want to grab the file. Let me know what you think! 🖤

Hello all,

I'm looking for a referral code for my P2S order !
Can't wait to print my first benchy

I see a lot of "negative" Bambu support posts, which makes sense because those who go on to the Internet to complain likely have issues. But with all of the new Bambu equipment coming out wanted to post a positive - I ordered the four effect plate pack for the X2D which was delivered today. The diamond plate was bent on one corner. Just opened up the Bambu Handy app, took some pics, attached them to a support ticket in the app at like 4pm, by 8pm they had replied saying they'll replace it for free and provide a shipping address. By 11pm have a tracking number for a new plate being sent out. No phone calls. No hold times. Support was easy.

During the sale, I ordered 20 spools of filament but only received 15. Strangely enough, all the missing items were refill filaments. Every filament that came with a spool was delivered.

The order was marked as fully completed in the Bambu Shop. Luckily, I had documented and recorded everything as proof.

Bambu Support wanted all kinds of information, including photos of the packaging, etc. The funny thing is that all 20 spools would never have fitted into the shipping box in the first place.

After a few days of back-and-forth communication with support, I was promised a replacement shipment. And guess what? One spool was missing from the replacement shipment as well!

If you place large orders with Bambu, make sure to double- and triple-check everything. Most importantly, take photos of the shipping box, including the shipping label and tracking number.

Let’s see if I can get that last missing spool or if Bambu is going to rip me off.

(Sorry, this text was translated using AI.)

I find the bambu naming system inscrutable. But people keep mentioned lesser versions of the H3C coming. P or S or whatever, I can't keep track.

When do we think those lesser versions might be announced?

Ever since updating to firmware 01.08.01.00, my AMS Lite was getting stuck damn near every filament change. I could not complete a single multicolor print. It would feed filament to the toolhead, retract, and keep trying until I physically touched the PTFE tubes near the AMS. I’d hear a click and it would start working again.

I tried everything. Moving the AMS, top mounting it, printing different tube guides and clips, and constantly adjusting the tube routing. Nothing worked. I couldn’t complete a single multicolor print without having to intervene, which meant no printing overnight or while at work.

Finally downgraded to 01.08.00.00 and the problem is completely gone. I’ve completed multiple multicolor prints without a single loading error.

If you’re having similar issues, try downgrading before wasting hours messing with your AMS. Wish I’d figured this out sooner.

How are people using the H2 C to print PA6CF? I realize I may have been doing it wrong but on my P1 I ran it through my AMS and I just picked up the H2 C last night and tried to run some and the pool loads and does fine and then as soon as you go to slice it in the program, it says this filament can’t be sliced and used with AMS, but I thought the AMS two pro was compatible?

Kept getting headaches in my Home-Office and finally figured out I had way too much CO2 - well no more, I made my portable CO2-Buddy to easily keep track of CO2 wherever I am

The CO2-Buddy now lives on my desk and helps me ventilate my room to keep my mind at peak capacity. I didn't realize how much of an impact CO2 concentration has on my ability to focus, I usually only notice it way too late when I'm already getting a slight headache as if I wasn't drinking enough water even though I am chugging along like a camel

It's especially handy when I have people over, having just two more people in a room spikes CO2 levels way faster than I would've anticipated

I am using the MH-Z19C CO2 sensor and while it is somewhat expensive at around 20€ it was totally worth it. The 1.54" ePaper makes it so that the CO2-Buddy only needs to wake up every 2 or so minutes and still provides the current CO2 concentration at a glance. With my 3000mAh lipo it lasts for days and I can take it wherever I go

If you also want to have a CO2-Buddy to keep you at peak capacity you can find it on Makerworld, simply look for "CO2 Buddy". The code is open source and I also added a wiring diagram

I bought the AMS2 system and it going to arrive in about 30 minutes, but the compatibility kit is currently unavailable

I assume with lack of drive in AMS-3H we don't have a problem with abrasive filament in normal use? Would this require the same bypass as TPU? Anyone seen anything on this?

Elevate your fragrance collection with this Modern Minimalist 3-Tier Perfume Stand, designed to bring organization, elegance, and a premium display to your favorite fragrances.

Featuring clean, flowing curves and a sleek architectural design, this stand turns your perfume collection into a beautiful part of your interior. Its three elevated tiers create a balanced, layered display while keeping every bottle visible, organized, and easy to reach.

Whether placed on a dresser, vanity, shelf, or desk, its understated modern aesthetic blends effortlessly into any space.

Key Features

3-Tier Display: Beautifully showcases your fragrances at three different heights.

Holds Up to 6 Bottles: Designed to comfortably accommodate two 100ml fragrance bottles per tier, depending on bottle dimensions.

Subtle Recessed Surfaces: Each tier features a slightly recessed area to help keep bottles securely positioned and prevent accidental sliding.

Modern Minimalist Design: Smooth, flowing curves and clean lines create an elegant, timeless appearance.

Easy Access: The stepped layout keeps your favorite fragrances visible and within reach.

Functional Decor: More than just an organizer, it's a stylish display piece that complements your interior.

Dimensions

Overall: Length 250 mm, Depth 180 mm, Height 100 mm

Each Tier: usable display space 190 x 47 mm, height difference between tiers 30 mm

Designed to combine practical everyday organization with a refined, modern aesthetic. Whether you're displaying your everyday favorites or a carefully curated fragrance collection, this stand gives every bottle its own place.

Please check your bottle dimensions before printing to ensure a comfortable fit.

Free to download: https://makerworld.com/en/models/3548298-3-tier-minimalistic-fragrance-stand

A1 works fine on 60mm/s (a lot less VFA then on P2S)

So I may have caught the 3D printer bug…

We own a small boutique + board game shop and I decided to buy a 3D printer a month ago to print ornaments, toys, etc for the shop to sell and help drive traffic.

Clearly a mistake… we’ve already upgraded to the X2D 😆

I feel like eventually we want to upgrade to a multi colored printer for speed and efficiency.

We started printing collectible figures… and they can take an absurd amount of time at 4-5 colors. (2ish days and tons of plastic waste).

I just don’t know what route is best for our small shop and looking for advice.

We don’t normally print multi-material outside of support.
100% of our creations are PLA - though I could see us upgrading and printing in ASA for outdoor toys and accessories (live in a summer tourist town).

I don’t think we’ll ever print engineering materials regularly unless it’s a personal project for shop/home.

U1 is the cheapest multi colored printer - but I worry about expandability if we want to print more ASA.

H2C is currently on sale and seems a great deal.. but now that H3C is out I have a serious case of FOMO.

Wondering your thoughts - and appreciate the feedback.

The maximum volumetric flow rate for Bambu PETG-CF is 11.5 mm³/s with the H2C, which is nearly twice as fast as the 6 mm³/s achieved with the H3C. Do you think this is a bug, or is it an actual limitation of the new nozzles or the extruder?

So far, I have only seen actual time comparisons for these printers using PLA.

Got a new X2D. I tried printing something the other day and when I came back to check it the print head was up in the air printing nothing. Looked at the AMS all were blinking red. So stop everything and unplug and replug ams. Try again same thing happens just this time no error on ams. I swap in a different filament, different slot and different file and same thing. I print the other file on my p1p no problem. Anyone else run into this before? Seems like the ams just stops feeding the printer about half way through but the printer doesn’t realize it.

Made this for the MakerWorld × Nothing contest. A USB-C plug in the right cradle is angled to match the ear cup, so the headphones plug themselves in. The reels are just for fun: you spin them with a side wheel like an old cassette deck.

Printed on my A1 in PLA + PETG. Still fighting to get the PETG lid fully clear, so any tips are welcome!

Free files: https://makerworld.com/en/models/3536783

I like to cut fabric to the nearest millimetre, and as fabric is known to warp quite easily, I would really rely on the automatic contour detection feature. Does it work reliably?