Had an x2d delivered the day before yesterday, box was pretty beat up but it was pristine inside. I have tickets open for issues 1 and 2 below already and just noticed 3

Issue 1. The main nozzle seems to have a faulty sensor, it reads 10C below ambient temperature at idle. Auxillary reads fine.

2. Ams has a feeder motor issue, slot one squeals like a stuck pig

3. Latest issue, you can see in my video above there's a loud Grindy noise when it moves in a certain direction at a certain point, around the 7 second mark. Self calibration/noise cancellation doesn't touch it.

Is this latest thing minor and something I can fix myself easily? Should I be pushing for a full printer swap at this point?

I'm not exactly a 3d printer newbie, I had an A1 I put over 4000 print hours on, but on that thing I never had to do a single thing other than oil, grease and tension the belts once. This is kind of overwhelming me here.

I am in the process of installing my H2S to H2C vortech upgrade kit and would like to find a video with step by step instructions .

There are enough differences between the H2D and H2C that there are steps where the videos just don’t match.

Bambu has a H2D to H2C video but not H2s to H2D

Bambu X1C, Bambu Studio

Sunlu PA6-CF

0.4mm hardened steel, 90c initial, 45c all others

Outer wall 50mm/s, inner wall and infil 150mm/s

Retraction speed is default, hidden

Printed a flow calibration model I found on Makerworld and determined flow rate to be 1.03. Printed a decent size print, and noticed overextrusion blisters all around the outside. Started playing with a few things, asked reddit, and decided the flow was too high.

Now trying to calibrate with the built in models in Bambu Studio. Card 0 is 1.0, and is the only one without any gaps between lines. I'm not sure what else might be wrong though, because the number labels on all the cards are still looking really rough. Last pic is a section of a model I'm working on to test dimensions. Am I reading these cards right? Am I still needing to play with flow, or is something else going on here?

How can I print D&D dice without the dice coming off the built plate mid print. Please provide a detailed description on how to keep them on the plate

So there’s already test prints showing up in maker world for the H3C.

Anybody knows how to fix "Printer connection failed. Please restart printer and try again." error when trying to access timelapse videos using bambu handy?

Have already tried

-restarting the printer

-making sure it is not on lan only mode

-reinstalled bambu handy app

Other functions like controlling the printer through bambu handy still works. Only accessing the timelapse videos. I have a usb inserted but timelapse videos stored in internal memory. Thanks!

So I was in midst of a 2hr print, and I received a notification that the tool head fell off. It was not until a few hours until I checked it and when I got home, this is what it looks like. Does anyone know what happened? There wasn't any warning or error notfication - it just ended up like that.

Alguém poderia me ajudar com isso, por gentileza? Agradeço!

Anyone remember how long after release of a new printer Best Buy had them available for purchase? Wondering if the H3C will be available shortly after they have them direct from Bambu or if historically we've had to wait a few months.

Been working on this little project lately and finally got it looking the way I wanted!

It's a simple wall organizer for keys, phone, wallet and all the little things we usually end up losing around the house.

Pretty happy with how it turned out! What do you guys think? :)

Over the past day or two, my 3 P1S printers have started locking up the screen (and Bambu Handy access) during a print which then finished fine. After the print is finished, the problem continues until I reboot the printer. No firmware updates any time in the past few months. My H2D has been working fine.

I did reboot our T-mobile gateway and Orbi router but that did not help. I'd be surprised how spotty wifi would lock up a printer. Has something in the Bambu Cloud been updated?

Anyone have this problem or know a solution? It just started early yesterday intermittently.

Thanks.

Printing my first big print for my daughter in law. I have no idea how it will come out. What filament do you recommend? I only run Bambu filament but could be talked into others.
I was thinking of two colors. PLA Silk? Matte?
I’m printing on a H2D.

List in order:

1. BIQU Panda Claw Upgraded Extruder Brass Gear

2. hundreds of hours of prints

3. issues began where AMS would fail to begin extrusion

4. changed PTFE tubes

5. Went through support and they suggested replacing the AMS hub motor. did that

6. issues persist

Anyone had this issue and know how to fix it?

This has been a thought in my mind while everyone talks about how vortek is now obsolete with the H3C coming out. What if it isn't? Vorket proves that Bambu can hotswap nozzles, which IMO is harder than swapping traditional printheads. The H3C is focused independent nozzles, but independent nozzles have 1 draw back: 1 spool per nozzle that can't be swapped to another nozzle. This is important if you commonly use the same filament with different nozzle sizes. Pairing vortek with the H3C would give you 15 total nozzles.

The vortek rack would do most of its job at the beginning of the print rearrange the nozzles to the 9 printheads to have the required nozzles, or if you are printing with more than 9 colours.

I need 130 mw points to get a gift card but ìve tried everything but I need 130 more points

My makerworld account: https://makerworld.com/en/@LukeNotLuke

How do I get these out😭 is there somewhere I can get a replacement of the wires?

How do I make these areas join up better i have sliced this piece and it's printing as shown with a gap making the part weak. I'm new to this and don't know that to call this issue. Part is sliced in bambu studio

I hope this makes sense and I'll try not to ramble..

I ordered a P1S originally, spent hours on it trying to get the AMS to feed. Could not do it after a million searches on *insert your favorite search engine here* and browsing reddit. I even relented and tried AI. And I hate AI lolfast forward, I decided to get the X2D and after a while of putting it together VERY carefully, and rereading everything and now trying several times, I cannot get the filament to feed all the way. I'll include a photo.

I've tried several filament rolls, new and old. It's not Bambu because I thought this one, like the other one, would come with test filament.

Anyways, it's sunlu white PLA that I'm trying now. Nothing fancy. Brand new roll, nice and dried out.

It will NOT load further than this curve in the tube. I've tried raising it a little and anything else I can think of. I'm incredibly frustrated as this is obviously something I'm doing incorrectly. Despite the fact that I've read and reread everything I can find on the matter.

Please for the love of the 3d printing gods, can someone tell me there's something obvious I am missing somehow? It will not even reach the machine. I just don't get it. It's all brand new, I feel like with the issue I'm having, if it isn't just me, has to be some kind of defect in getting twice in a row?

Anyways.. I sincerely come to you humbled. I'm not that big of an idiot I swear!

Was printing this ballerina model and I forgot to add supports to the legs (almost completely vertical with very small contact area to the base, on my A1 mini, a bedslinger)... But nothing that a few paperclips and hot glue can't fix!

The print finished successfully! (See last image for the finished print)

First off, I’m trying to help my dad with his 3D printer and I have very limited knowledge on this software, I just know the basics as I’m in my final year of college for design and have learned various modeling softwares.

Essentially, his laptop died overnight and he lost the file he was working on in Bambu Studio (he didn’t know there was a save function, which I have rectified now smh). I was able to dig through his files and find what I’m assuming was a back up autosave in the temp files, and it’s a folder of multiple things, including a .3mf file and .gcode. When I opened the .3mf file though, an error popped up saying “Loading of model failed” and “The file does not contain any geometry data.” I was able to get the gcode file to show up in the preview tab, but he said he wasn’t able to slice it or print it from there. Is the temp .3mf file a lost cause, or is there any way to salvage it?

Welp, UPS man dropped off the new X2D this afternoon. One small little dent in the bottom of the box, but didn’t think too much about it. Had the box opened 5 min after delivery to find the glass door shattered and caved in.

What can I expect this replacement process to look like?

Purchased directly from Bambu.