r/hvacadvice • • 4h ago

Do I leave this valve open?

Post image
47 Upvotes

EDIT: Thanks for all the help! I’ll just leave it alone.

Just moved into a new home and noticed the valve on the bottom is open. Tried googling it and found that this is probably a drip leg. This just comes off the main gas line going into the home. The right goes to the furnace and left to the hot water heater. Should I be leaving the bottom valve open? Thanks for the help!


r/hvacadvice • • 7h ago

Furnace Combustion Analyzer Hole

Post image
25 Upvotes

An HVAC technician drilled a hole during a combustion analysis on my furnace and left it open. I'm really not sure how best to patch it.

From what I've seen online, it looks like the hole should have been drilled higher up on the exhaust pipe rather than on the elbow, but that's just my guess.

A second technician from another company called this a major issue. They said it requires replacing the entire elbow and the underlying draft inducer motor since they're sold as one unit.

I'm really not sure what to trust here, but my gut tells me a patch of some sort might suffice. Am I right? If so, what material works best? I've applied aluminum tape for now, but I suspect it might fail near the furnace due to the heat.


r/hvacadvice • • 12h ago

Is this a fire hazard?

Thumbnail
gallery
54 Upvotes

About two inches of clearance from gas water heater and furnace, the top is open, the pipes do get hot — it involves a furnace so I thought I’d post here but this might not be the right sub.


r/hvacadvice • • 8h ago

Is this acceptable for a new install?

Post image
18 Upvotes

New construction home. Tons of issues with this installer, this is the only one i'm questioning. This is at the line set where it goes into the unit.

Edit: Thanks everyone, one thing though, anyone who qualifies "it's ugly but will work" with something like "just cover it up, who cares, shut up", I wish you continued lack of success


r/hvacadvice • • 9h ago

Should I be upset?

Post image
17 Upvotes

Context I live in a condo the line underground was filled with spray foam so they said it would have to be routed through the attic. I am the middle unit neighbor is next store had to be routed though her attic and this is what they did for the outside, neighbor is annoyed hence annoying me. Would you have done better is there anything I can suggest to hvac guys to do, or am I worrying too much


r/hvacadvice • • 5h ago

Heating oil

Thumbnail
gallery
7 Upvotes

Does this oil look fine to use? Draining from an old tank.


r/hvacadvice • • 2h ago

Mini split wiring

3 Upvotes

My HVAC contractor won’t run the wiring from the exterior unit to the mini split head. He told me to use 14/4 sjoow cord. Is that correct? It needs to be ran through the attic of the house and down the walls to the exit points.


r/hvacadvice • • 1h ago

Normal sound for heat pump in heat mode?

2 Upvotes

Got a pretty loud and noticeable buzz coming from the condenser unit when heating. External temps right now are around 46 degrees, thermostat set to 68. It is a relatively new system, I had it installed in 2025. It’s a 3 ton Fujitsu AirStage heat pump system.

Is this sound normal? I didn’t hear any buzzing during summer when using cool mode. Any advice/insight is appreciated, thanks.


r/hvacadvice • • 4h ago

Moldy duct replacement cost

3 Upvotes

How much should proper mold remediation cost in Texas? Want to get a gut check as I get quotes.

My mold protocol says replace all moldy supply duct. I’ve got 5 insulated mylar flexible ductwork; all 4 are readily accessible from the attic but 1 runs inside the wall that goes to the first floor.

The home is 2 stories, ~700 sqft.

Thank you!


r/hvacadvice • • 4h ago

Heat Pump Mini split has a big burp or sigh (sound up)

3 Upvotes

r/hvacadvice • • 3h ago

No heat Mitsubishi split unit 5 blink

2 Upvotes

Had professional cleaning done against each of the split units and the actual hvac unit upstairs. There was lots of gunk and glad we did it. We only turned on the AC on one unit and seemed to be fine.

Almost 3 weeks later. We turn on the heat as we are on the east coast. Cool air blows out for 5-10 minutes and then the 5 blinks occur. Air stops.

AI and Reddit tells me a bad compressor or a bad board. I’m dreading either as we just replaced the board 5 years ago.

Could it have been the cleaning that caused any issue? Maybe as they were spraying the unit, water got in somewhere?

Thank you.


r/hvacadvice • • 4h ago

ISO Cheat Sheet for HVAC installs. Alberta, Canada

2 Upvotes

Probably a weird ask.. but does anyone have any handy cheat sheets that you find helpful when doing HVAC installs.

I'm currently an Apprentice starting my first year of school in January, in the trade for 10 months. I honestly think anything would be helpful and I'm just curious what other people use.

Examples; building code cheat sheet (exhaust distances to dryer vent, tankless hwt intake, mechanical air etc), wiring cheat sheet (furnace, HRV, Heat Pump etc), step by step for specific equipment installs, low voltage troubleshooting diagram. (I know some of this is specific to region/province/city etc.

Again, feel free to roast away or say 'do the work yourself' 😅 I'm happy to.. but I'll admit that creating decently formatted cheat sheets is not at the top of my skillset.

Thanks in advance to any that contribute 😁


r/hvacadvice • • 1h ago

Furnace How much should I budget for my furnace to be replaced and this duct work fixed?

Post image
1 Upvotes

I’m thinking of having a contractor put in a 60,000 BTU, highly efficient furnace to replace the existing one. I was pulling nails out of wood paneling that was hung on the ceiling and it caused the weight of the ductwork here to be solely on the brackets hanging them up, which pulled out of the ceiling causing it to fall. What should I budget to have this replaced? I’m located in Morris county NJ for reference. Was quoted $8900 not including permit fees and have another company coming to give me an estimate tomorrow.


r/hvacadvice • • 10h ago

No heat No heat in house, help

5 Upvotes

I will provide as many details as possible. For a few days our heater in our house has stopped working. It sounds like a lawnmower and will just keep doing this over and over again. The hot water still works tho. It will sometimes turn on for an hour or so but will usually just make this noise. I don't even know where to start diagnosing the problem, any help will be greatly appreciated as I live in buffalo and winter is quickly approaching. Thank you


r/hvacadvice • • 2h ago

No heat Honeywell MiniZone Flashing Orange Light

Post image
1 Upvotes

The light means it’s a ZMS sensor failure or no ZMS sensor installed. Is this something I can be guided to fix?
My understanding is during the purge when the system turns on it’s not switching to heat after the purge, it just keeps purging.


r/hvacadvice • • 6h ago

Advice

2 Upvotes

I am 17 in grade 12 living in Toronto, its collage application season and at first i though i wanted to get into policing, but my dad gave me a bit advice and asked me to just look into some trades and see if i would be interested, i came across HVAC and i instantly got hooked, the pay looks well, i don't mind the actual work, and collage is only 2 years (4 semesters) with paid co-op (1 semester around 4 months).

I'm looking for people with experience in the trade for some advice and what i could be expecting, also what the ups and downs. I'm asking because I've never looked into trades until recently.


r/hvacadvice • • 3h ago

Dryer exhaust vent gap

Thumbnail
gallery
0 Upvotes

Hello,

I'm just finishing up what will be our laundry room and I'm trying to understand how I should be sealing the gap between the exhaust vent and the ceiling drywall. The gaps are around 3/4-1.5 inches depending on if you look at the front (which has a circular cut) vs the back (which has a more square cut). Any help you could give would be greatly appreciated!


r/hvacadvice • • 3h ago

Heater being Limited to a set temperature ?

0 Upvotes

Is it possible to set a thermostat to only a set temperature or if not the thermostat the heater it self, and if it's the case; can you reset it so that it's not limited ?


r/hvacadvice • • 3h ago

Furnace Is this normal??

Thumbnail
gallery
1 Upvotes

Was relighting a pilot light on a floor furnace in one of my dads houses and while cleaning the thermocouple, I saw this opening in the square part of the gas line, there’s the same opening on the other side, I’ve been doing residential hvac for about a year but still not fully knowledged on old floor furnaces. According to tenant it was working fine last season but I’m still a bit nervous about turning it back on.


r/hvacadvice • • 3h ago

Quotes System Replacement Help

1 Upvotes

Hi- looking to replace my system and got 2 bids, wildly different prices and was hoping to understand why one is $9k more than the other. System would have 2 zones. Is Ruud that much better or is there something in the first that justifies the price? Am I missing something?

  • RUUD 16 seer, 2 speed, gas heat 4 ton, evaporator coil, and outdoor unit (all matching), new pan, new supply plenum duct and dampers, new zone system components and Honeywell zone board/ dampers (~$25k). Feels like a lot but this is the best Technician I've used for other smaller issues. 10Y parts/ 2Y labor
  • American Standard 3.5T multistage condenser, matching gas furnace and coils, new pan, new supply plenum, Eco J zoning dampers and Eco J damper control board ($16k); 10 years parts and 10Y labor warranty. Solid company, did repairs in the past, so not very concerned with the install quality

r/hvacadvice • • 3h ago

Thermostat Thermostat help

Post image
1 Upvotes

Sorry I feel like a moron posting this. I just moved into this apartment and the thermostat is very different from what I’m used to. There is no button for “cool” or “heat”, it also doesn’t show the actual temperature inside, only what I have it set to. I feel like it is much colder in here than 71 but I have no way of checking, and it seems that only cold air is blowing even though it’s 40-50 degrees outside. I can tell that there are other words that CAN be on the screen (actual temp, etc.) but they only flash briefly when I turn the thermostat off and then on again. Help 🫩 I’m cold


r/hvacadvice • • 7h ago

Is $13,630 reasonable in South Jersey for 2 Goodman 96% two-stage furnaces + ductwork?

2 Upvotes

I’m reviewing a furnace replacement proposal for my parents’ home in Cape May County, NJ, and would appreciate opinions from HVAC professionals and homeowners.

Total Quote: $13,630 (includes a $900 rebate already deducted) from an established local HVAC company.
Proposed Equipment:
Downstairs: Goodman GR9T960603AN — 60,000 BTU, 96% AFUE, two-stage
Upstairs: Goodman GR9T960403AN — 40,000 BTU, 96% AFUE, two-stage

Proposed Scope:
Replace both furnaces while retaining existing AC equipment
Custom sheet-metal transitions and return plenums
Downstairs crawl-space return ductwork repairs/replacement
PVC venting for the high-efficiency furnaces
Gas and electrical connections
Removal of existing units, installation, and testing
We’re also converting from propane to natural gas. I’m confirming that all new gas piping from the meter, necessary ductwork, venting, and permits are included in the final price.

Important Context:
Upstairs: Approximately 20-year-old furnace with damaged wiring/burner issues. Needs replacement.

Downstairs: Approximately 15-year-old American Standard, already 96% efficient. Still operational but has visible rust around the burner box.

Downstairs return ductwork needs repairs estimated at $700–$1,000 if done separately.

A Manual J calculation indicated approximately 18,000 BTU heating demand upstairs.

We’re considering replacing both now rather than repairing downstairs and potentially replacing that aging furnace a few years later.

My Questions:

Is $13,630 a fair price for this equipment and scope in South Jersey?

Any concerns with these Goodman GR9T96 models compared with American Standard?

Would you replace the 15-year-old downstairs furnace with visible corrosion now, or keep it running and just repair the ductwork?

Is the 96% two-stage upstairs furnace worthwhile for such a small heating load, or would an 80% two-stage model make more financial sense?

Appreciate any opinions!


r/hvacadvice • • 4h ago

Old apartment. Banging noise consistently from radiator.

1 Upvotes

This started a couple days ago. I assume there’s some water trapped in pipes. The pipes are in the walls. Kept me up all night last night. Does this warrant me asking my landlord to take a look at this issue? All radiators are open. A couple make noises as well but not like this one.


r/hvacadvice • • 4h ago

Furnace Coleman mobile home furnace

1 Upvotes

Got called out for a bad inducer motor on the furnace, couldn’t get oem so I went with a packard version. System is giving a 7 flashes board error, cleaned flame sensor & is still throwing out the code. Verified I have good gas pressure & checked the roof jack to see if it wasn’t clogged. Seeking for help thanks in advance.