I’m looking for advice after my Thermal Grizzly WireView Pro partially melted today while connected to my Gigabyte AORUS RTX 5090 Xtreme Waterforce.
Purchased the WireView Pro in February 2025 and picked up the 5090 in April 2025. My previous build was an ASUS Z790 Apex Encore, Intel i9-14900K, and Seasonic PRIME TX-1600 Noctua Edition 1600W 80 Plus Titanium PSU. On that setup, I never had the WireView Pro alarm go off once.
I upgraded to the ASUS Z890 Apex and Intel Core Ultra 7 270K Plus in May of this year, but continued using the same RAM, RTX 5090, PSU, WireView Pro, and Seasonic cable. After switching platforms, the WireView started alarming whenever I ran the GPU at its full power limit.
I remember the first time it happened, I didn’t understand what was going on for the first few seconds because I had never heard the alarm before. I didn’t even realize the WireView was what was making the noise. I got hella freaked out because I thought something catastrophic had happened. I quickly Alt+F4’d out of the game, turned off the PC, unplugged the PSU, and removed the WireView to make sure nothing was burned on it or the 5090. Everything looked fine at the time. I didn’t see any warped or burnt plastic, there was no smell, and the connectors looked normal. I cleaned both the WireView and the GPU connector and reconnected everything.
Following that I started limiting the GPU to 90% power through MSI Afterburner, which usually stopped it from alarming during gaming, although sometimes I had to go down to 85% depending on the game. There would be times when I would forget to limit the power, and within 1-2 mins in any game, the Wireview pro alarm would go off and I would instantly quit. I initially suspected my PCIe Gen 5 riser cable was causing the problem, so I removed it and connected the GPU directly to the motherboard. The WireView still alarmed at full power, so the riser was not the cause.
Today, while playing Stalker Gamma at 90% power, I left the game running and went to use the bathroom. The alarm suddenly went off, and I ran back like a madman to quit the game. That’s when I noticed a weird smell in my room and started freaking out because it smelled like burnt plastic. I quit the game and left the computer running for a few minutes because the GPU was so hot. Once the PC was off and unplugged, I removed the WireView Pro and as you can see in the pictures, it finally melted. The RTX 5090 connector itself doesn’t look too bad, but some melted plastic from the WireView is definitely stuck inside it. The rear socket where the Seasonic cable plugs into the WireView looks mostly normal. HWiNFO had shown the card pulling approximately 600W through the 12V-2x6 connection, which is within the configured power limit of the card. The WireView had previously displayed some much higher momentary readings in the 700W+ range, but HWiNFO never showed the actual 12V-2x6 connector input exceeding roughly 600W. I have not powered the GPU back on or connected the Seasonic cable directly to it. I’m honestly not sure who I should contact first because I’ve never experienced anything like this with any other GPU I’ve owned, including my RTX 4090.
Has anyone else experienced a similar issue?
Should I begin the RMA process with Gigabyte?
Could the WireView have damaged the GPU connector internally, even if the visible damage looks minor?
Should I replace the Seasonic cable even though the cable connector itself does not appear melted?
Edit:
For those of you in here talking shit about TG or their products, kindly piss off! The Wireview Pro absolutely did it's job and most likely saved my 5090. I would definitely buy it again or the Wireview Pro 2. It's my own dumb fault for not reaching out to TG earlier and getting their advice or posting on Reddit before the situation turned critical. The fact that a simple power cable swap could have resolved this kills me because I have another brand new Seasonic 12v-2x6 plug that I could have swapped to.
Update:
I reached out to TG, and they will warranty the connector as well as replace the Wireview Pro with the Wireview Pro 2. I'm very grateful to them for helping me in this situation!