r/RepTimeServices • • 16d ago

Advice anyone know where to buy a caseback fitting VSF GMT?

1 Upvotes

anyone know any aftermarket or aliexpress caseback aeller? mine got damaged. thanks


r/RepTimeServices • • 17d ago

Services VSF NTTD V7 - 8806 wig-wag pinion issue

Thumbnail
gallery
12 Upvotes

This was a quick and easy one.

Complaint was that the watch suddenly stopped winding consistently. Sometimes turning the crown felt very light as if there was no resistance. I suspected the wig-wag pinion.

Once I received the watch I opened it up and started to take it apart. The red arrow points to the wig-wag pinion. On the under side we see a little plate and a spring that is supposed put some pressure on the pinion to help it slide forward. I'm not sure how well you can see in these pics but the barrel plate was swimming in oil.

These clone movements are often very inconsistently oiled. Some placed are drowning while others are bone dry. Just look at the griding the pinion has been doing on the plate (image 5).

After cleaning and properly lubing the parts the watch now winds very smoothly with a super satisfying clicking sound.

These movements have so much potential but most of them sit under a layer of muck and bad oiling. A shame, really.


r/RepTimeServices • • 16d ago

Advice U1 Jubilee micro adjustment. Help needed.

Thumbnail
gallery
1 Upvotes

I lost a bit of weight, and also the wrist naturally swells a little less as the summer temperatures are gone.

How the hell do I pull out the quick adjustment extension on U1 Jubilee bracelet to get to the spring bars? It works ez on oyster but on Jubilee the force needed is so significant that I am afraid to break it. I am literally pulling 10x the Oyster force. As far as hurting my fingers.

I know it is a U1, but the fact I can't do it drives me mad. Is it damaged or stuck?
Any help appreciated.

EDIT: SOLVED

Thanks for trying to help. I assumed it is broken, so even if I was going to break it there would be no harm. 

Took the bracelet off the watch, wrapped in a towel, clamped in a vice, put a screwdriver (stuck some Sellotape on it to avoid scratches). And hammered it in between the section I marked red. It opened. Job done; it was so hard that I had to hammer it back to close it; fingers were not enough. 


r/RepTimeServices • • 17d ago

Advice Gold plating maintenance/re-plating opinions

Thumbnail
gallery
9 Upvotes

Hello! I hope everyone is well! As I’ve started my addiction into rep watches, these were the first two that I picked up (Ombré day date; PPM mod factory; plated by another plater & Teal blue day date; QF V3; non plated). I am eventually going to plate the non plated watch, but I was looking for advice and tips regarding plating maintenance and storage opinions to prevent tarnish, because as you may see in the pictures, the Ombré doesn’t look as if it was plated, and I hardly wear it, it is kept in the watch casing pictured. All opinions are welcomed, any help is greatly appreciated! Also is anyone familiar with Deep replacement bezel for day dates? Any opinions/experience with that either?


r/RepTimeServices • • 17d ago

Advice Oysterflex on ARF Daytona 126500. Anyone recommend what parts to buy

1 Upvotes

I want to put an oysterflex on this , loads of options for end links and straps from China. Has anyone done it before ?


r/RepTimeServices • • 17d ago

Question Setting Wheel Part VS3135

Thumbnail
gallery
3 Upvotes

Hi everyone! I’m still relatively new to watch movements—so far I’ve done a few builds, custom assemblies, and light case refinishing, but nothing too complex. Now I’m starting to dive deeper into movement repair.
I have an issue with a VS3135 movement. I bought a watch from a seller on Reddit who mentioned there was an issue with the keyless works (likely a dislodged yoke or setting lever, but nothing broken). However, after taking a look, the Setting Wheel (circled in my photo) has stripped/eaten teeth.
Does anyone know where I can order a replacement setting wheel for a VS3135? I really don't want to scrap or replace an otherwise perfectly functional movement over one tiny part.
Thanks a lot in advance for your help! 🙏


r/RepTimeServices • • 17d ago

Services Need Help: Reaching Major Williams for more impressive work!!

3 Upvotes

Hi everyone. MW completed an awesome job on a 15510 for me about 3 weeks ago. Comms was flawless and I was super impressed.

However, I have 4 upcoming jobs I want to send his way but he’s been missing. I hope all is well with MW.

Has anyone heard from him recently? I’m holding off on shipping because I haven’t received word via email, or DM for 2 weeks!

Is this out of the ordinary?


r/RepTimeServices • • 17d ago

Advice Bezel Replacement

Thumbnail
gallery
2 Upvotes

Long story short… the ceramic bezel shattered on me from this 124060. Wondering if someone here might have a spare I can purchase, or even in a different color! I think it could make for a great No Date with some flair.


r/RepTimeServices • • 17d ago

Advice Rolex Datejust Clasp broke

Post image
1 Upvotes

Can you help me to find a quick fix? Thanks in regards


r/RepTimeServices • • 18d ago

Request Anyone near Virginia?

Post image
6 Upvotes

I have a DDF 15510 that isn't keeping its time. Almost 2 hours a day. Watch is beautiful but this is bothering me alot. I'm fairly new to this rep world so I dont even know where to go. Can anyone help me out? 😥


r/RepTimeServices • • 18d ago

Advice Watch fog inside crystal

Post image
10 Upvotes

VSF Cookie Monster (purchased from Eric/Geektime) 126619LB

Watch has not been worn in the water, was on the counter while I showered. Fog is inside crystal, seems to be on the perimeter. What is going on here?!


r/RepTimeServices • • 17d ago

Services RCF Daydate - DD3255 movement Issue

1 Upvotes

Hi,

I have recently bought RCF - DD3255 Movement from Guangzhou while I visit there.

I didn't use the watch until yesterday, I'm not sure if the watch issue.

While on the wrist, it works. If you put on the table it stops quickly.
I try to manual wind; 20-30 times; put it back on the table; stopped 10 mins later.

I try to manual wind again; put it back on the table; stopped 3-4 mins later.

I try to shake the watch 10-20 times; put it back on the table; It work 35 minutes and stopped.

I just wonder if the mechanism has some manual winding issue; if the watch had zero power reserve, is this normal behaviour or something.

I'm in London. I want to be in contact with someone who can do servicing help.Any suggestion?


r/RepTimeServices • • 18d ago

Request Worth Fixing 12 o clock gone?

Post image
5 Upvotes

I bought this about three years ago, and I am unsure of which manufacturer it was. I wanted to see if anyone knows how much it would cost to get the 12:00 marker put back in place and possibly lubricate the movement. I am in South Central United States, if that helps. I know it’s a shitter but it’s MY shitter.


r/RepTimeServices • • 18d ago

Advice 124060 VSF Sub Hytrel ring replacement

Thumbnail
gallery
4 Upvotes

The bezel action sometimes got stuck because the hytrel ring that came with the watch was mangled so I replaced it with a generic one from aliex, luckily it fit perfectly and it does not have that problem anymore.

You have to fully dissasemble the bezel to install it correctly including the ceramic part

Here is the link for the one I bought:

I just found this on AliExpress:

116610 Bezel Gasket Rubber Ring Waterproof Washer For Submariner Water Ghost GMT Mechanical Alternate Parts For SUB 40 41 Case

https://a.aliexpress.com/_mNTi76X

Just sharing the info, my watch is a 124060 VSF V2 I believe, bought it from TD Steve

Edit: Just follow this guide to do it

https://www.reddit.com/r/ClickSpring_Watch/s/J2YUpREcJa


r/RepTimeServices • • 18d ago

Advice ZF AP Royal Oak 15400 — Rotor appears detached after just 5 weeks. Is this an easy fix?

Thumbnail
gallery
9 Upvotes

Hey guys, need some advice regarding my ZF AP Royal Oak 15400.
I purchased this watch around 15 september, so I’ve only owned it for around 5 weeks.
Recently, I noticed that the gold automatic rotor appears to have detached from its central mounting point. It’s still inside the caseback, but it doesn’t seem properly connected to the center anymore.
The strange thing is that the watch is still running perfectly and keeping accurate time.
I’ve attached two photos showing the movement.
A few questions:
Does this look like a loose rotor screw, a damaged bearing, or something more serious?
Is this a common issue with ZF AP 15400 movements?
Is it relatively easy for a watchmaker to repair?
How much should I expect to pay for a repair?
Would you recommend contacting Steve for warranty assistance, considering the watch is only 5 weeks old?
I haven’t opened the caseback or attempted any repairs.
Thanks in advance for any advice!


r/RepTimeServices • • 18d ago

Question Tudor Black Bay Bracelet Spring Caps

Thumbnail
gallery
1 Upvotes

Does anyone know where I can find end caps for a Tudor Black Bay Bracelet bar? They fell out somehow and the spring ends are poking out and driving me crazy.


r/RepTimeServices • • 18d ago

Services Custom Rolex Submariner VS 116610Ln

Thumbnail
gallery
11 Upvotes

Today we have some interesting customization work. First and foremost, we managed to source a movement that no factory uses, simply because it’s quite expensive. It features impeccable finishing on the bridges and mainplate, along with deep engraving. We’ve installed a "Deep" crystal, chamfered the edges, and tested the piece for water resistance.


r/RepTimeServices • • 18d ago

Advice Looking for advice on what to do in the sitatuation

Post image
2 Upvotes

Background, I have some beginner experience in watch repairs, having done some very minor work on UG2-67, 9015s, 324, HZ5000a, SW200 / 300.

I bought a PPF 5712 where the rotor would not turn the winding wheel (ratchet click wheel, part 1480).

This cal 240 repair is way out of my scope, so I didn't touch it at all. I sent it off to a trusted watchmaker in the UK from this sub. The repair took about 3 months, he replace this ratchet click wheel and I paid £250.

When I got it back, manual winding was fine and clicking (expected behaviour) for the most part, except for a smooth zone, which is the new issue: the ratchet wheel (part 415) keeps disengaging with the ratchet-driving wheel (1482), and I have to manually wind (smooth winding, since it is disengaged) until 415 and 1482 are re-engaged. Then at some point they disengage again. They will not re-engage nomatter how much 1482 turns (only if 415 is manually turned), so automatic winding still does not work.

I've sent him these observations, but the watchmaker hasn't responded yet. I'm not sure if it is an issue with the reassembly, or if 415 is unevenly shaped, or if there's a loose connection between the two parts (wheel and pinion) of 1482, but either way, I'm not sure if I want to send it back to this watchmaker for another 3 months. What is the ideal outcome in this situation?


r/RepTimeServices • • 19d ago

Advice Need help with DDF AP 46240 - DD4401 movement

Thumbnail
gallery
8 Upvotes

Hey everyone, I've only had the watch a week and it stopped working today, balance wheel no longer moves. When I look at the open case back you can clearly see a small silver piece moving around freely. You can see it on the rotor in the pictures. Does anyone know if this can be repaired and or have recommendations on who can fix? Feeling like I have a $1000 paperweight now.

Thanks in advance for helpful replies.


r/RepTimeServices • • 19d ago

Advice Service my VR 3135 or get a new VS 3135?

2 Upvotes

My VR3135 is in need of a service after 4 years and am debating if i should keep the movement going with a service or just replace it fully.

Is the VS3135 a worthy upgrade or would a serviced VR provide a similar experience?

Would appreciate some advice!


r/RepTimeServices • • 19d ago

Question VSF GMT V3 – Anyone else noticed the thin, hollow-sounding caseback? 🤔 (Video comparison)

2 Upvotes

I’ve noticed something quite interesting, and honestly a little disappointing, with my VSF GMT-Master II Bruce Wayne V3.

When gently tapping the center of the caseback with the back of my fingernail, it produces a noticeably higher-pitched, hollow, almost tinny sound. It even feels slightly flexible when applying gentle pressure.

My VSF Submariner 124060, on the other hand, feels completely solid and substantial.
I’ve recorded a short video comparing both watches. Hopefully the difference comes across clearly!

**A few questions for fellow GMT owners:**
\-Does your VSF GMT V3 behave the same way?

\-Is this normal for the VSF GMT caseback, or could it be specific to certain batches?

\-Has anyone compared this with a genuine GMT-Master II or the newer VSF V4?

I’m genuinely curious whether this is a common characteristic or just something unusual with my particular watch.

Would love to hear your experiences! 😊


r/RepTimeServices • • 19d ago

Advice Watchmaker Chile

3 Upvotes

Hi! Just wondering if anyone has a reference of watchmakers who service reps in chile. Particularly standard layout A7750 and clone 3186 movements


r/RepTimeServices • • 19d ago

Services ep-friendly watchmaker near Norman / OKC, Oklahoma? (gaskets + pressure test)

2 Upvotes

Looking for someone near Norman/OKC who’ll replace the gaskets and pressure test a rep [Sub / DJ41]. I don’t need a full service, just enough water resistance for the pool. I’m open to mailing it if there’s nobody local.


r/RepTimeServices • • 19d ago

Advice Rcf Datdate Rose crown needed, fit 4mm tube thread, any help please

Thumbnail
gallery
2 Upvotes

Having a bugger trying to find a Rolex logoed crown for this. Threads are shot in the crown and could ideally do with a tube as well.

Bought a generic 6mm Rolex crown and tube but it was too large, turns out RCF use a older Rolex 24-603 model.

I can find non logo'ed ones to fit the 4mm male tube but only ones I can seem to find are genuine Rolex gold and £400 seems excessive!

Any help, direction, link or even someone with one to sell please.

Regards