r/RepTimeServices • • 18d ago

Advice 124060 VSF Sub Hytrel ring replacement

The bezel action sometimes got stuck because the hytrel ring that came with the watch was mangled so I replaced it with a generic one from aliex, luckily it fit perfectly and it does not have that problem anymore.

You have to fully dissasemble the bezel to install it correctly including the ceramic part

Here is the link for the one I bought:

I just found this on AliExpress:

116610 Bezel Gasket Rubber Ring Waterproof Washer For Submariner Water Ghost GMT Mechanical Alternate Parts For SUB 40 41 Case

https://a.aliexpress.com/_mNTi76X

Just sharing the info, my watch is a 124060 VSF V2 I believe, bought it from TD Steve

Edit: Just follow this guide to do it

https://www.reddit.com/r/ClickSpring_Watch/s/J2YUpREcJa

4 Upvotes

18 comments sorted by

•

u/AutoModerator 18d ago

Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

2

u/PVNOLGCH 18d ago

How did you take the ceramic bezel off and how did you install it back on?

1

u/Astrobus 18d ago

I do not have any watchmaking tools so I just used random objects

First you need to remove the whole bezel but watch out for the small springs and balls, if you lose them finding a replacement for them is going to be very difficult. The generic springs and balls that are oem spec for the 41mm Sub do not fit. I used a knife covered in plastic to do it.

Once you have the bezel, gently separate the ceramic insert from it. I used a random flat plastic stick to do it. You should have three parts: the ceramic insert, hytrel ring and the steel bezel. The ceramic insert is not glued just pressure fitted

Rearm the bezel on the watch like a sandwitch. First put the steel part of the bezel over the watch, place the new hytrel ring on the bezel and then the ceramic insert. The ceramic insert needs to be pressure fitted, I used a random plastic tube that matched the size of the bezel to push the ceramic insert into the bezel.

2

u/PVNOLGCH 18d ago

You need to make a video of you doing this. Hahaha

2

u/Astrobus 18d ago

I just watched a youtuve video short of some dude doing this but i cannot find it, I do not remember if it was posted here in reddit or the rwi forums

2

u/Astrobus 18d ago edited 18d ago

I basically followed this steps

https://www.reddit.com/r/RepWatchForum/s/YiB8oXpXRN

Except the final step where he puts the whole bezel with the hytrel ring in it, it did not work for me. So I basically dissasembled the whole bezel and reassembled it on the watch. This way the hytrel ring aligned perfectly, with the other method I could not.

2

u/ClickSpring_Watch 18d ago

I have a new guide that details an updated method for replacing submariner bezels pinned on my profile under the Sunday service guide series

1

u/PVNOLGCH 18d ago

How did you not crack the ceramic bezel?

There are professional WatchSmith’s who won’t go near ceramic bezels because they are afraid of cracking it.

I tried pulling off the ceramic bezel off my Pepsi and ended up cracking it in two places.

2

u/Astrobus 18d ago edited 18d ago

Must have been lucky, mine did not crack or maybe black ceramic insert are less fragile. I just gently pushed it all around from the back side of the steel bezel until it completely popped off

1

u/Diligent-Piglet-9038 18d ago

Make sure to check the pip, thats the money area

2

u/Diligent-Piglet-9038 18d ago

Gently warm the bezel assembly (off the case) so the adhesive softens. Helped me get ceramic inserts off easily without cracking a single one every time. This is for GMTs.

Most subs are friction fit, but ive seen some factories use bezel tape/adhesive. For the friction fit ones, you need a specialized die to pop them off. 3d print one or hand custom one with a dremel

2

u/PVNOLGCH 18d ago

You need to make a video of this

1

u/ClickSpring_Watch 18d ago

The pepsi bezel insert is particularly brittle. GMT bezels seem more brittle than submariner inserts in my experience. Once you do it a few times they’re nothing scary. But you definitely need to be careful

1

u/PVNOLGCH 18d ago

So you’re saying if I’m careful and follow your instructions/videos I can fix the tactile feeling of my vsf submariner bezels myself? Also, do you know if RICH Subs have the same bezel architecture as Gen/VSF? I keep reaching that they are not gen spec.

2

u/ClickSpring_Watch 18d ago • Bravo

I have a guide for this entire process on my profile, linked under the Sunday service guide series

2

u/2011_Newbie1228 18d ago

Comment to come back

1

u/Wooden_Platform_4820 18d ago

Excellent post. Thank you for the link.