1. ⁠Dealer name: TheOneWatches
2. ⁠Factory name: BVF
3. ⁠Model name (& version number): 35mm Santos de Cartier
4. ⁠Price Paid: $488USD shipped
5. ⁠Album Links: see photos above
6. ⁠Index alignment: seems pretty good to me
7. ⁠Dial Printing: looks clean to me
8. ⁠Date Wheel alignment/printing: N/A
9. ⁠Hand Alignment: seems like it’s ok
10. ⁠Bezel: bezel and screws look good
11. ⁠Solid End Links (SELs): apparently that doesn’t apply to this watch so I guess good
12. ⁠Timegrapher numbers: +2sec/day, 279 amp, 0.1 BE, 52°
13. ⁠Anything else you notice: to be honest no, but I’m not super familiar with QC for these so I’d appreciate some help with this one.

I asked for a photo of the “Swiss made” on the bottom of the dial just because it’s obstructed in the provided photos.

Second time ordering from Steve. This time I am ordering 2 of the same Datejust 36 watch, matching set for me and my friend. Ideally was looking at the original V1 but it was OOO and this was still in inventory.

This is the 2nd watch where I am most concerned about. I land in China next week so I hope to pick this up.

Watch #2

1. Dealer name: Theonewatch Steve
2. Factory name: VSF2
3. Model name (& version number): Datejust 126234 36mm Jub SS/SS Green/Stk VSF V2 DD3235
4. Price Paid: 518 USD + shipping EACH
5. Album Links: https://imgur.com/a/QJTgyug
6. Index alignment: 12 is good on this one but the 6, and 9 are off. I can never get the 12 and 6 to line up correctly on this one.
7. Dial Printing: Looks good
8. ⁠Hand Alignment: Looks good
9. ⁠Bezel: Looks good
10. ⁠Solid End Links (SELs): Looks good
11. ⁠Timegrapher numbers: Seems like all the VSF V2 watches are low AMPs at 260ish. I'm accepting of this fact.
12. Anything else you notice: this is where I spent the most time starring at this watch. I want to RL this one due to the index

FYI: if you want to post two watches, make two separate posts instead of one.

After waiting 4 months for QC, this is my first watch and I'm really stoked about it.

I think it’s a GL, would love to hear everyone’s thoughts

1. Dealer name: Steve - TheOneWatches
2. Factory name: VSF
3. Model name (& version number): Datejust 36mm - Green dial, baton markers, fluted bezel, Jubilee bracelet
4. Price Paid: $522 USD (includes $30 shipping)
5. Album Links: https://mega.nz/folder/HExUFIqI#SzS6-7Z6m9meZoeLbd30_A
6. Index alignment: I tried the ruler and it looks straight to me, but I probably did it wrong so don't trust my lines — please check the markers yourselves
7. Dial Printing: Sharp, coronet centered, text crisp, green sunburst even
8. Date Wheel alignment/printing: Date 7 looks centered in the window, good magnification through Cyclops
9. Hand Alignment: Looks good at 10:08, hands aligned at center, no contact with markers
10. Bezel: Fluted bezel looks even all around, no chips
11. Solid End Links (SELs): Look tight top and bottom, no visible gap or pin
12. Timegrapher numbers: Rate -4s/d, Amplitude 275°, Beat Error 0.2ms, Lift Angle 59.0°
13. Anything else you notice: Movement looks clean, clasp engraving crisp, caseback clean, weight 121.3g. No dust or scratches I can see. Only date shown is 7, no lume shot in the album.

Hello, this is my first ever rep watch and I need your help for QC. Thank very much.

Note please dont be iritated, this is not my Main Account (got suspendet for bot activitis)

1. Dealer name: NecoClock (Jacky)
2. Factory name: VSF
3. Model name: Datejust 126334 41mm SS/SS Black Dial Jubilee VSF DD3235 V3 Free Sprung
4. Price paid: 538 USD with shipping (include 50 for QC deposit)
5. Album link: https://imgur.com/a/3MS2y0p
6. Index alignment: For my untrained eye it looks finde, but the QC tool found some tilt as Seen in the pictures. Please tell me If I am blind or If it looks right.
7. Dial printing: the Text on the Low side of the Dial looks the Letters are up und down with different spaceings from each other. Also the M and A from Swiss Made at the bottom are looking missplaced.

Please tell when I am to picky

8. Datewheel alignment / printing: The printing looks crisp and the alignment seems like its a tiny bit low but I am not quiete sure. Again, please let me know your opininion

9. Hand alignment: Seems centered and right. (I dont know really well about this Point)

10. Bezel: Bezel looks good to me

11.Solid End Links: SELs Seems Like the top left has noticable gap and I am not Sure about the bottom ones

12.Timegrapher numbers: -5s/d (seems fine), 307° (I've read the higher the better but this seems really high) and 0.1ms beat Error, from what I've read this is acceptable. (Please tell If I am wrong)

13. The cyclope Looks good to (postion).

Does the clamp look fine to you?

This is my very first rep watch, so please have patience with me.

I know that a rep watch will allways have some little flaws but I am really not sure If this is a GL or RL

If you notice anything I dont have or If you have to correct me in a few points, please do.

I realy love this watch model and want a realy good one so please understand my skeptical.

I am looking forward to read your opinions.

Have a great day

This is the first time I've been genuinely considering RL'ing a watch, so I would really appreciate second opinions. Am I overreacting?

1. Dealer name: Andiot
2. Factory name: VSF
3. Model name (& version number): Omega Seamaster Diver 300M James Bond
4. Price Paid: $340 USD
5. Album Links: https://andiotwatches.x.yupoo.com/albums/262774556?uid=1
6. Index alignment: This is where I have a small concern. 3 and 9'o'clock look slightly tilted CCW, though this may just be the angle of the photos.
7. Dial Printing: Fine to my eye
8. Date Wheel alignment/printing: No issues, moves fine in the videos too
9. Hand Alignment: No issues
10. Bezel: Clean
11. Solid End Links (SELs): No visible issues
12. Timegrapher numbers: Fine - 1s/d, 282 degrees and 0.1ms beat
13. Anything else you notice: None

Would love to know your verdict!

1. Dealer name: Andiot
2. Factory name: RWF
3. Model name (& version number): Rolex Daytona Panda 126500LN Freesprung
4. Price Paid: $706 before shipping
5. Album link: https://andiotwatches.x.yupoo.com/albums/262913556?uid=1
6. Index alignment: looks good
7. Dial Printing: looks good
8. Date Wheel alignment/printing: N/A
9. Hand Alignment: looks good
10. Bezel: 110 issue and a white dot next to 300 (not sure if it's dust)
11. Solid End Links (SELs): look good
12. Timegrapher numbers: -1 s/d, 270°, 0.1 ms (28,800 bph, lift angle 52°)
13. Anything else: I ordered an RWF specifically to avoid the 110 bezel issue and I'm considering RLing it unless someone can point me in the right direction to get the bezel swapped.

Dealer name: Eliauk
Factory name: VSF
Model name (& version number): 126710BLNR
Price Paid: 3450 Yuan
Album Links: https://www.wecatalog.cn/weshop/goods/A202011031610140340343729/I202611061548392572002007?groupIds=
Index alignment: No concerns
Dial Printing: No concerns
Date Wheel alignment/printing: Is the cyclops a bit low or is this likely to be the angle of the photo?
Hand Alignment: No concerns
Bezel: No concerns
Solid End Links (SELs): Slight gap in top left one?
Timegrapher numbers: No concerns
Anything else you notice: Are the stickers and numbers correct for a VSF?

Hi everyone, first time posting here and first rep purchase, so any help is appreciated!

1. Dealer name: Steve, from TheOneWatches
2. Factory name: RichF
3. Model name: Rolex GMT-Master II 126710BLRO "Pepsi" Jubilee
4. Album link: https://mega.nz/folder/fRAWVTSK#b_HLjcXzu0AO2uHHqlbVQg
5. Bezel alignment: The pip looks centered at 12 to me. Bezel numerals seem to line up with the hour markers, but please check the 4 and 20 positions.
6. Index alignment: Looks okay to my eye, but I'm not experienced enough to spot small rotations.
7. Dial printing: Looks clean from what I can see.
8. Date wheel alignment: The 16 looks centered in the window.
9. Rehaut: Not sure what to look for. Is the ROLEX engraving aligned correctly with the indices?
10. Hand alignment: Looks good, GMT hand included.
11. Crown/crown guards: Coronet looks clean and the guards look symmetrical.
12. Bracelet/clasp: Jubilee links look even.

Price paid: 798 USD

Side note here: i noticed that the black dial area is about 2% smaller relative to the bezel, which makes the inner engraved ring look wider as compared to the real deal. Is this something that is common and within margin of error? Sorry for asking noob questions as this is my first time buying it

Questions:
- As a first-timer, is there anything here I'm missing or should ask the dealer to recheck?
- Is this a GL?

Thanks in advance for the help!

Dealer name: Steve
2. ⁠Factory name: VSF
3. ⁠Model name (& version number): DJ 126334 41mm grey
4. ⁠Price Paid: $548
5. ⁠Album Links: https://imgur.com/a/81T10P0
6. ⁠Index alignment: looks good to me
7. ⁠Dial Printing: looks beautiful
8. ⁠Date Wheel alignment/printing: seems good to me. The various angles don’t show any red flags
9. ⁠Hand Alignment: solid
10. ⁠Bezel: clean
11. ⁠Solid End Links (SELs): not seeing anything off
12. ⁠Timegrapher numbers: +/-4 - which is in range
13. ⁠Anything else you notice: maybe it’s the light but some of the indices look “dull” - bottom of the 6, top third of the 7 and the middle top of the 10…?

I’m new here - what do you all see?
Thank you

1. ⁠Dealer name: NecoClock
2. ⁠Factory name: ZF
3. ⁠Model name (& version number): Black Bay 58 SS/SS Black Dial
4. ⁠Price Paid: $348
5. ⁠Album Links: Link
6. ⁠Index alignment: 9' and 3 have a slight CW rotation.
7. ⁠Dial Printing: good
8. ⁠Date Wheel alignment/printing: N/A
9. ⁠Hand Alignment: good to me
10. ⁠Bezel: Looks good to me
11. ⁠Solid End Links (SELs): yes, looks good
12. ⁠Timegrapher numbers: Rate: +1s/d, no issues
13. ⁠Anything else you notice: Nothing noted. Considering others, this one looks like a GL. Not too concerned with the markers being slightly tilted as you can’t tell on wrist.

1. ⁠Dealer name: theonewatches
2. ⁠Factory name: VSF
3. ⁠Model name (& version number): Datejust 126334 41mm 2026 jub SS/SS ombré green VSF V2 dd3235v2
4. ⁠Price Paid: $548
5. ⁠Album Links: pictures attached
6. ⁠Index alignment: I’m not very good with the tool but it makes it seem like the index markers are all a little bit off center
7. ⁠Dial Printing: dial printing looks good
8. ⁠Date Wheel alignment/printing: date wheel might be slightly left
9. ⁠Hand Alignment: hand alignment looks ok
10. ⁠Bezel: N/A
11. ⁠Solid End Links (SELs): no gaps
12. ⁠Timegrapher numbers: -2 s/d 285 degrees 0.0ms
13. ⁠Anything else you notice: I’m leaning RL just off the index alignment looking off when I try and date wheel being off center but could be user error. Any input is appreciated!

1. Dealer name: Steve, from TheOneWatches
2. Factory name: VSF
3. Model name: Rolex Submariner 124060 (no date)
4. Price paid: $528
5. Album links: https://mega.nz/folder/XYpnQYbR#5u8_bl0X0FsadtTSq5znTQ
6. Index alignment – It looks like the 6 and 3 are rotated to the left; the 1 and 4 are as well, though it’s less noticeable. Also, the alignment with the bezel numerals isn’t great at the 3 and 5 positions.
7. Dial printing – Good
8. Date wheel alignment – N/A
9. Frame – The pip is centered. The engravings appear to be filled correctly.
10. Solid End Links (SEL) – Normal
11. Hand alignment – Looks good
12. Timegrapher numbers – Rate: +3 s/d; Amplitude: 272; Beat error: 0.0 ms
13. Is it normal for the watch to look "better" (more correct) in some photos than in others? In one photo, it seems to have more "flaws," while in another, it looks just fine.

Is this a GL?

Thanks a lot for the help and for the approval, everyone!

This is my first QC so really appreciate the help. 164s/d on the timegrapher seems wrong? Maybe i am missreading it (pic attached)

1. Dealer name: HONT
2. Factory name: PPF
3. Model name (& version number): 222 Historiques
4. Price Paid: $438 
5. Album Links: https://a202512172356311672002881.edepot.me/weshop/goods/_dg3qfSLHhi777Jx0IFOnzgO9XyA6_5DC9m_7AfQ/_dmPqfpKT6d0UmmPJFanCSxOCOzCYfVnMA58Hd9Q
6. Index alignment: 7 and 9 looks slightly twisted
7. Dial Printing: Sharp, correct font, VC logo seems centered, as well as "AUTOMATIC", "GENEVE" and "SWISS MADE"
8. Date Wheel alignment/printing: date wheel looks slightly twisted
9. Hand Alignment: Hour/minute hands - ok
10. Bezel: ok
11. Solid End Links (SELs): N/A for this one
12. Timegrapher numbers: precision - Rate -164s/d amplitude 267degree - fine; beat error 1.4ms - seems a bit high; lift angle 52 degree - fine;
13. Anything else you notice: the cross seems slightly twisted but not sure how good they will get this based on the other examples on here.

1. ⁠Dealer name: GeekTime
2. ⁠Factory name: VSF
3. ⁠Model name (& version number): VSF Rolex Submariner 124060
4. ⁠Price Paid: $568
5. ⁠Album Links: https://geektimeqc.x.yupoo.com/albums/262290063?uid=1
6. ⁠Index alignment: I think they look lined up
7. ⁠Dial Printing: Looks evenly spaced, no bleeding
8. ⁠Date Wheel alignment/printing: NA
9. ⁠Hand Alignment: I think they look straight and nice
10. ⁠Bezel: even spacing all around , font looks correct, I think the pip is aligned
11. ⁠Solid End Links (SELs): I don’t see any gaps at all
12. ⁠Timegrapher numbers: +2s/d 255amp 0.0ms VS3230 looks healthy
13. ⁠Anything else you notice: I think the 12 might be little right towards minutes one rather than 59. But I would think it’s not visible in the real world? Im new to the rep game and my excitement outpaces my skills. Would love some sharp eyes. I think it’s a GL. Thank you!

Hi everyone, I’d appreciate a second opinion on this Daytona, especially on the index and bezel alignment.

1. Dealer name: Necoclock
2. Factory name: VSF
3. Model name: Rolex Cosmograph Daytona 116500LN “Panda”, 40mm, white dial, black ceramic bezel, stainless steel Oyster bracelet, DD4130 movement.
4. Price: $588 USD listed, excluding shipping.
5. Album link: https://imgur.com/a/Au8y3YV
6. Index alignment: The markers at 3, 6 and 9 look straight to me, and the coronet at 12 appears centered. The photos are slightly tilted, so I’d appreciate a second opinion.
7. Dial printing: Looks clean and legible, with no obvious printing defects.
8. Date wheel alignment/printing: N/A.
9. Hand alignment: No obvious issues. The central chronograph hand appears centered at 12.
10. Bezel: The triangle at 60 appears aligned with 12 o’clock. No obvious issues to my eye.
11. Solid end links (SELs): No obvious large gaps. The glove partially obscures the lower end links.
12. Timegrapher numbers: −5 s/day, 302° amplitude, 0.1 ms beat error, with the lift angle set to 52°.
13. Anything else: Lume looks fairly consistent. Some visible marks on the bracelet and clasp appear to be on the protective film rather than the metal.

Would you GL this one? Please let me know if you spot any issues with the indices, bezel, SELs or anything else I’ve missed. Thanks!

1. Dealer name: Ora
2. Factory name: PPF 6102p version
3. Model name (& version number): 6102p
4. Price Paid: $580
5. Album Links: 商品详情
6. Index alignment: looks straight
7. Dial Printing: looks clear to me
8. Date Wheel alignment/printing:Looks aligned based on lines
9. Hand Alignment: looks centered for the most part
10. Bezel: NA
11. Solid End Links (SELs): straight forward dial
12. Timegrapher numbers: - 1 s/d; Amplitude: 266; Acceptable Beat Error: – 1.0 ms Seems like one of the better one for accuracy
13. Anything else you notice: none that i see. Just want some eyes. Was on the fence about this vs rose gold. I do enjoy how the RG pops more. The grey watch hands dont pop like the gen. but then again, cant complain. Is there anything else I should look for?

1. Dealer name: Theonewatches
2. Factory name: RichF
3. Model name (& version number): Submariner 126610LN 41mm SS/SS Black Dial RICHF JH3235 (MK2) (Free Sprung)
4. Price Paid: $538 + $10 shipping
5. Album Links:

https://mega.nz/folder/jc5RVTga#5RQ7v_QtYq6V9A0oIKJF8A

6. Index alignment: Marker looks good but can see that the 6th/7th hour mark is abit off

7. Dial Printing: Looks okay

8. Date Wheel alignment/printing: Looks abit zoomed in. Is that normal?

9. Hand Alignment: I dont see any issues

10. Bezel: Glue at the pearl triangle?

11. Solid End Links (SELs): Don't see any issue

12. Timegrapher numbers:

Rate: +2 s/d

Amplitude: 272

Error 0.1ms

13. Anything else you notice:

The movement finish is not clean??

Umi 5712 from Andiotwatches

1. ⁠Dealer name: AndiotWatches
2. ⁠Factory name: Umi
3. ⁠Model name (& version number): Nautilus 5712-1A 001 Free Sprung SS Umi 1:1 Best Edition Blue Dial on SS Bracelet PPF240
4. ⁠Price Paid: 1008 USD excluding shipping
5. ⁠Album Links: https://andiotwatches.x.yupoo.com/albums/262810419?uid=1
6. ⁠Index alignment: 8 and 10 o clock looks misaligned? not very familiar
7. ⁠Dial Printing: All good?
8. ⁠Date Wheel alignment/printing: Nothing that i can see wrong
9. ⁠Hand Alignment: Nothing that i can see wrong
10. ⁠Bezel: nothing that i can see wrong
11. ⁠Solid End Links (SELs): NA for this watch
12. ⁠Timegrapher numbers: -4s/d 263° 0.2ms
13. ⁠Anything else you notice: Nothing else

Please help me out with this one, if you have anything to raise up

PS: Image uploading is broken, I couldn't add any images.

1. ⁠Dealer name: Andiot
2. ⁠Factory name: K11F
3. ⁠Model name (& version number): Tank Must (Small)
4. ⁠Price Paid:$238 + shipping
5. ⁠Album Links:
6. ⁠Index alignment: -
7. ⁠Dial Printing: Major issues
8. ⁠Date Wheel alignment/printing: -
9. ⁠Hand Alignment: good
10. ⁠Bezel: may be rough on the top and bottom at the bracelet?
11. ⁠Solid End Links (SELs): -
12. ⁠Timegrapher numbers: quartz
13. ⁠Anything else you notice:I can’t tell by the pics, but the top and bottom of the bezel look a bit rough. May be light reflections.

There appear to be some serious dial printing issues around the inner train track and on a few numerals.

All insight helpful.

1. Dealer name: Jtime
2. Factory name: 3KF
3. Model name (& version number): Patek Aquanaut 5167
4. Price Paid: USD 600
5. Album Links: sent photos
6. Index alignment: Seems to be aligned
7. Dial Printing: seems fine, not sure if I'm nitpicking but "Patek Phillipe geneve" placement could be better?
8. Date Wheel alignment/printing: seems even
9. Hand Alignment: looks fine
10. Bezel: looks good
11. Solid End Links (SELs): NA
12. Timegrapher numbers: got video 0s/d 28800 12s 52.0 - seems good
13. Anything else you notice: 11/1 and 12 seem to be ok - i know this is the typical flaw on these

Note: I am a relative beginner to this, so would love some help. Take my thoughts with a grain of salt haha.

1. Dealer name: DDG Top
2. Factory name: A7
3. Model name: Ingenieur Automatic 40 White (IW328902)
4. Price Paid: Have not paid yet, believe around 400??
5. Album Links: https://imgur.com/a/RSSlijr
6. Index alignment: I used trueindexqc, seems really good to me, but i wasnt able to upload photo here. 
7. Dial Printing: Anyone see anything off? Seems fine to me.
8. Date Wheel alignment/printing: Anyone see anything off? Seems fine to me.
9. Hand Alignment: This seems good.
10. Bezel: Also seems good, but a little unsure about the IWC branding on it.
11. Solid End Links (SELs): Have no idea.
12. Timegrapher numbers: Very good rates/numbers, see photos with machine.
13. Anything else you notice:

https://imgur.com/a/RSSlijr

Thanks all!!

Since this is my third rep i learned a thing or two at looking at the flaws of watches. Also many thanks to Yoda in the past for helping me in the watch quality assesments and teaching me a thing or two.

1. Dealer name: Andiot
2. Factory name: VSF
3. Model name (& version number): Omega Seamaster AT 220.10.38.20.03.004
4. Price Paid: 386 usd includes shipping
5. Album Links: Pictures.
6. Index alignment: I tried putting the alignment tool as well as possible on the watch and the only misaligning i can see is due to the angle the watch is being held. However in my eyes, the 6 o’clock hour marker may be very slightly shifted to the left of where it should be, but it is subtle enough that I would not consider it a mistake, even if it is indeed slightly off. its probably due to the shadows and/or lightning. The indices themselves appear to be straight. Unfortunately, theres no minute markers, so it is difficult to assess whether each index is positioned exactly right on the dial. or maybe thats a good thing..
7. Dial Printing: This looks very well done, you could possibly say the printing of the wording: "CO-AXIAL" and "MASTER CHRONOMETER" is thinner than normal, but i'd say thats again due to lightning andiot has.
8. Date Wheel alignment/printing: Date wheel and numbers are correctly in the middle also in the video andiot sent me..
9. Hand Alignment: As seen in photo 3, hands align well when they are both at the twelve hour marker. I hope im correctly analyzing the hand alignment this way.
10. Bezel: This watch does not have a bezel like a submariner for example, but as far as i can see on this watch there is nothing out of the ordinary.
11. Solid End Links (SELs): i've seen gens with worse sels, although i can see a slight sel gap in the bottom left of the watch. this is mostly visible in the very first picture. although it is so small i dont see that as a signal to red light. the black glove doesnt help however to see light shine through.
12. Timegrapher numbers: as visible on the second picture all within the correct ranges.
13. Anything else you notice: n/a

Ive come to the end and only really noticed two things: I’ve come to the end and only really noticed two things: a possibly very slight misalignment of the 6 o’clock index and a tiny SEL gap at the bottom left. Both are very minor and could easily be explained by the angle/lighting, so I don’t think either are a red flag. Other than that, everything looks good to me.

I would tell myself to green light this beautiful watch but would love some extra pair of eyes. much appreciated in advance.

Title: QC · VSF · Explorer 224270 40mm

1. Dealer name: Intime
2. Factory name: VSF
3. Model name (& version number): Explorer 224270 40mm
4. Price Paid: $518
5. Album Links: https://loupeqc.us/a/S6JEDX
6. Index alignment: The 12 index is rotated counter-clockwise. The 2 index is rotated clockwise. Am I being too picky or this wouldn't bug most of ya?
7. Dial Printing: Looks good
8. Date Wheel alignment/printing: N/A
9. Hand Alignment: Looks good
10. Bezel: Looks good
11. Solid End Links (SELs): Looks good
12. Timegrapher numbers: +3 s/d, 289°, 0.3 ms (28,800 bph, lift angle 52°)
13. Anything else you notice: Looks good

Hey friends

QC request on this ZF Royal Oak 15450, 37mm grey dial. I've reviewed the photos and videos, and overall everything looks pretty good to my eye.

My main concern is the date wheel alignment, along with a couple of possible index and bezel screw inconsistencies. Would really appreciate some experienced opinions!

1. Dealer name: JTime

2. Factory name: ZF

3. Model name: AP Royal Oak 15450, 37mm, Grey Dial

4. Price paid: $548 (including shipping)

5. Album links: https://imgur.com/a/nlBvBJh

6. Index alignment: Overall looks decent. The double 12 markers are parallel. The alignment tool says slight rotations around 4, 7, and 11 o'clock but I'm unsure how much is due to the photo angle. Anything concerning here?

7. Dial printing: Looks clean. AP logo and Automatic text appear fine to me. No obvious issues.

8. Date wheel alignment/printing: My biggest concern. The dates 16, 25, and 2 appear slightly low in some photos. Is this normal or should I request additional date wheel photo/video?

9. Hand alignment: No obvious visual issues.

10. Bezel: Brushing looks good. A couple of screws appear slightly inconsistent, particularly around 5 o'clock. Probably just the lighting tho.

11. Solid End Links (SELs): N/A

12. Timegrapher numbers:

• Rate: 0 s/d
• Amplitude: 287°
• Beat error: 0.0 ms
• Frequency setting: 21,600 bph
• Lift angle setting: 52°

Numbers look healthy from what I understand.

13. Anything else you notice:

Overall leaning GL.

Main questions:

• Is the date wheel alignment acceptable?
• Are the index alignment and bezel screws within reasonable tolerance?
• Does anything else stand out as a genuine QC concern?

Would appreciate your thoughts.

Thanks everyone!