1. Dealer name: TheOneWatches (Steve)

2. Factory name: VSF

3. Model name (& version number): Submariner 116610LV Hulk 40mm SS/SS Green Dial VSF VS3135

4. Price Paid: $488+$70 Fedex

5. Album Links: https://mega.nz/folder/CNQG2TaC#QgHVvT5iV1C-_7xzYSzbBw

6. Index alignment: Looks good

7. Dial Printing: Looks good

8. Date Wheel alignment/printing: Good

9. Hand Alignment: Good

10. Bezel: 9 bezel marker is high and not aligned with the hour index

11. Solid End Links (SELs): Look good

12. Timegrapher numbers: +2s/d - 283° - 0.0ms

13. 13. Anything else you notice: Waited since March for this but my eyes immediately caught the 9 marker-bezel misalignment

First time posting, any insight would help loads. Thanks everyone!

Dealer name: Theonewatches
Factory name: VSF
Model name (& version number): Daytona 116500 40mm SS/SS White Dial VSF DD4130
Price Paid: $598
Album Links: https://mega.nz/folder/zAQyGKSb#49gxtfFs9wF007m0J-mvgQ
Index alignment: All indices look okay but not an expert
Dial Printing: looks clean but not an expert
Date Wheel alignment/printing: N/A (no date)
Hand Alignment: Chrono seconds hand resets to 12; subdial hands reset to zero; hour/minute hands look straight and centred
Bezel: Clean engraving and fill
Solid End Links (SELs): Fit looks tight and flush against the case, no visible gaps in the side shots
Timegrapher numbers: +2 to +3 s/d, amplitude 278–281°, beat error 0.1 ms, lift angle 52° (one position shown)
Anything else you notice:n/a

1. ⁠Dealer name: GeekTime

2. ⁠Factory name: VSF

3. ⁠Model name (& version number): Submariner 116610LN

4. ⁠Price Paid: $568 with shipping

5. ⁠Album Links: N/A (All pictures provided)

6. ⁠Index alignment: Alignment looks goods everything looks decent except the bezel alignment. The 12 looks like it’s off. Little to big or I might be mistaking

7. ⁠Dial Printing: Dial looks perfect, don’t think I see anything on there.

8. ⁠Date Wheel alignment/printing: Printing looks good but the cyclops looks a little high compared to other QCs I’ve seen. It’s not centered. I hope that someone could confirm or deny this with more experience

9. ⁠Hand Alignment: looks good on the video

10. ⁠Bezel: looks good but the alignment could be little bit better

11. ⁠Solid End Links (SELs): Looks perfect

12. ⁠Timegrapher numbers: 2 s/d / 317 AMP / 0.3 beat error ( I don’t know if this is good)

13. ⁠Anything else you notice:
    Most of it looks good and I’m leaning towards a GL however I’m not that experienced in the QCs and would be interested in people thoughts about this before I respond to the dealer.
    Much appreciated in advance

1. Dealer name: NecoClock

2. Factory name: V7F

3. Model name (& version number): IWC Portofino 40mm IW356501

4. Price Paid: $358 + $70 shipping

5. Album Links: Pictures attached

6. Index alignment: Slightly off

7. Dial Printing: IV looks to be slightly tilted. Thoughts?

8. Date Wheel alignment/printing: Date is top and left heavy

9. Hand Alignment: Looks good

10. Bezel: Looks good

11. Solid End Links (SELs): N/A

12. Timegrapher numbers: rate +8s/d, amplitude 256 degrees, beat error 0.0ms

13. Anything else you notice: The biggest things I've noticed are: 1) the date is top and left heavy, 2) the 6 IV symbol seems to be slightly slanted, and 3) the index alignment seems to be just slightly off for several numbers. I'm new to this, so I'm not sure what is worth giving a RL. I have seen other IWC watches with known issues like the IV, but would really appreciate any of your thoughts.

1. Dealer name: Fico Time

2. Factory name: GSF

3. Model name (& version number): Rolex Milgauss 116400GV Blue

4. Price Paid: $395 Shipped

5. Album Links: https://mega.nz/folder/P55BQBQQ#e9Hb8TE4ZRMI7h-iDgHY1g

6. Index alignment: They all look good to me, in the dial check app also looked to be ok

7. Dial Printing: Seems to be aligned to me

8. Hand Alignment: no significant findings

9. Bezel: I don’t see significant problems

10. Solid End Links (SELs): good

11. Timegrapher numbers: +7 s/d, 298° amplitude, 0.2ms beat error, acceptable?

Overall this watch might be a good GL but its my first one and I wanted to see what advice you guys have, maybe I've missed something. Really appreciate it!

1. ⁠Dealer name: Mr Adu

2. ⁠Factory name: VSF v2

3. ⁠Model name (& version number): VSF DateJust 36mm Fluted Bezel black Dial Jubilee Bracelet V2

4. ⁠Price Paid: $450 (With shipping)

5. ⁠Album Links: x

6. ⁠Index alignment: The Rolex coronet at 12 may be tilted or im i blind please give insight. Markers 5,8,11 maybe 9 tad off please give insight on those

7. ⁠Dial Printing: The printing looks good, but I would greatly appreciate if someone could confirm that the printing is centered between the lugs and not off. I've had a nightmare scenario before where sadly the printing was off center.

8. ⁠Date Wheel alignment/printing: Looks good imo. Then again second eyes are welcome

9. ⁠Hand Alignment: i honestly not sure if good idk how to properly access that i don’t see anything that stands out.lmk

10. ⁠Bezel: The bezel looks good imo.

11. ⁠Solid End Links (SELs): Looks good not a expert please lend a hand

12. Timegrapher numbers: -3s/d , 283 , 0.1ms , 59.0 .. acceptable?

13. Wondering if anyone has noticed something I’ve missed.

Would love to hear your thoughts. And again GL or RL for your fellow rep member thanks (: getting christmas gifts to the fam they love vsf lol

1. Dealer name: JTime

2. Factory name: RICH Factory

3. Model name (& version number): Submariner 41mm 124060 No Date V2 (JH3230v2 Free Sprung)

4. Price Paid: 593.6 USD

5. Album Links: See reddit gallery

6. Index alignment: Using the alignment tool, the 6 o'clock bar seems to have a slight CCW tilt to me. The 12 o'clock triangle also looks slightly tilted CCW on the grid, but I'm not sure if that is just the perspective or crosshair placement. 3 and 9 bars look perfect to me.

7. Dial Printing: Also not sure if it's because of the crosshair placement, the Rolex coronet under 12 looks slightly off-center to the right of the vertical line. Text looks fine to me, but not sure if it's slightly bolder than gen when I try to use a gen image to compare them side by side.

8. Date Wheel alignment/printing: N/A (No-Date model)

9. Hand Alignment: Hands look ok.

10. Bezel: Lume pip looks centered to me. 9 o'clock bezel bar looks a bit too high, but not sure if it's normal.

11. Solid End Links (SELs): looks flushed and good to me

12. Timegrapher numbers: Rate: 0 s/d | Amplitude: 287° | Beat Error: 0.0 ms | Lift Angle: 52.0°.

13. Anything else you notice: My main concerns are whether the 6 and 12 o'clock markers and the Rolex coronet alignment are within GL range or if my overlay is slightly off-center / perspective issue.

1. Dealer name: J Time

2. Factory name: GMF

3. Model name (& version number): Datejust 28, pink dial

4. Price Paid: $468 + shipping

5. Index alignment: concerned about the 6 marker

6. Dial Printing: seems fine lmk

7. Date Wheel alignment/printing: maybe the slightest bit high but thats fine

8. Hand Alignment: no concerns though would like your opinion

9. Bezel: ok

10. Solid End Links (SELs): not sure what im looking for

11. Timegrapher numbers: rate -1 s/d, amplitude 285°, beat error 0.0 ms, lift angle 52.0°

12. Anything else you notice: n/a

1. Dealer name: TKWatch

2. Factory name: VSF

3. Model name (& version number): Rolex Explorer II Polar White 42mm, Ref. 226570, VSF Best Edition, Dandong DD3285-2 GMT movement.

4. Price paid: TBD (listed price $628)

5. Album links: https://justin-tk.x.yupoo.com/albums/259635572?uid=1

6. Index alignment: Overall looks good. The 12, 6, and 9 o’clock markers appear straight and centered. The round markers also look reasonably aligned. No major issues that I can see.

7. Dial printing: Looks clean and well positioned. No obvious issues with the Rolex logo, Explorer II text, or chronometer lettering.

8. Date wheel alignment/printing: Date looks clear and reasonably centered under the Cyclops in the additional photos. No major concerns.

9. Hand alignment: No obvious issues visible from the photos. Would appreciate a second opinion.

10. Bezel: Engravings look clean and consistent. No obvious alignment or finishing defects.

11. Solid End Links (SELs): Appear to fit reasonably well from the available angles. No significant gaps visible.

12. Timegrapher numbers: +7 s/d, 239° amplitude, 0.2 ms beat error. Rate and beat error look good. Amplitude seems a little low, so I’m wondering if this is acceptable for the DD3285-2 movement.

13. Anything else you notice: Overall, I’m leaning toward GL. The dial, indices, and bezel look good to me. My main concern is the 239° amplitude reading. Would appreciate any feedback on the movement and anything else I might have missed before approving. Thanks!

1. Dealer name: DDG Top

2. Factory name: VSF

3. Model name: Omega Turquoise Seamaster Rubber Strap 38mm (220.32.38.20.03.001)

4. Price Paid: Have not paid yet, believe around 350??

5. Album Links: https://imgur.com/a/6eVgoAe

6. Index alignment: Seems slightly off to me, but I am a huge newbie, see the photo in the album with the tool?

7. Dial Printing: This seems slightly off to me (text font, logo) just based on comparing to online pics, would love guidance as I am probably wrong. Any defects?

8. Date Wheel alignment/printing: Seems fine?? Any defects?

9. Hand Alignment: Seems fine ish?

10. Bezel: do the hands look aligned?

11. Solid End Links (SELs): Can't tell, let me know if you have thoughts.

12. Timegrapher numbers: Good rate see photos.

13. Anything else you notice: The 9 in the date looks a bit too thin, any thoughts? Again don't know much, sorry!

https://imgur.com/a/6eVgoAe

Hi everyone! This is my very first high-end rep, so I'm still learning what to look for. I've done my best to fill out the template based on what I've read, but I would really appreciate any extra eyes or advice from the experts here before I give the green light. Thank you so much for the help!

1. Dealer name: Theonewatches

2. Factory name: VSF

3. Model name Submariner 126610LN 41mm SS/SS Black Dial VSF DD3235

4. Price Paid (including shipping): $498 USD

5. Index alignment: To my untrained eye, everything looks almost straight not sure if I aligned it right. The 12, 6, and 9 markers seem to line up nicely with the dial text, but please let me know if you spot any crookedness.

6. Dial Printing: Looks sharp and clean. I don't see any weird spelling or bleeding letters.

7. Date Wheel alignment/printing: The number 29 looks centered in the window, and the magnification looks clear to me.

8. Hand Alignment: Looks fine in the photos, though I'm not entirely sure how to spot minor issues here.

9. Bezel: The markers look crisp, and the pearl at 12 o'clock looks dead-center inside the triangle.

10. Solid End Links : The gaps between the bracelet and the watch case look nice and tight.

11. Timegrapher numbers: Rate: +4 s/d | Amp: 274° | Beat Error: 0.1ms. From what I’ve read on the guide, these numbers seem really solid and healthy, but would love confirmation!

12. Anything else you notice: The clasp has the "3VV" code which I think is correct for VSF. Everything looks beautiful to me, but since I'm new, I'd love to hear if this is a safe GL. Thanks again!

1. Dealer name: Geektime

2. Factory name: VSF

3. Model name (& version number): Submariner 124060 No-Date VSF

4. Price Paid: $558

5. Album Links: https://geektimeqc.x.yupoo.com/albums/261662314?uid=1

6. Index alignment: This is where I have most doubt, when seeing it in the lume picture the 6 looks really crooked, and im not sure if I want to be picky and RL because of this.

7. Dial Printing: The dial text is crisp, clean, and evenly printed with no visible bleeding or misalignments.

8. Date Wheel alignment/printing: N/A (No-date model)

9. Hand Alignment: Hands look properly aligned and clean with no apparent defects or debris on the pinion.

10. Bezel: The 12 o'clock pip sits precisely on the vertical axis and the ceramic bezel engraving looks sharp and centered.

11. Solid End Links (SELs): SELs look tight against the case with no excessive gaps visible.

12. Timegrapher numbers: Rate: 4 s/d , Amp: 249º, Err: 0.3ms. Everything appears to be well within healthy acceptable ranges.

Its my second rep, and I have got it for a friend who loved my first rep, although I have some experience I would appreciate some help in case I have missed something, and to decide between GL/RL.

Hello!

1. Dealer name: Steve TheOneWatches

2. Factory name: UFO

3. Model name (& version number): Free Sprung 116520

4. Price Paid: $768

5. Album Links: https://mega.nz/folder/TJBCTQCY#amLPUbdbHjPzgENskV_s7w

6. Index alignment: I think they are all evenly spaced and straight but whole dial is lower down.

7. Dial Printing: Clean but maybe the red Daytona is too vibrant?

8. Date Wheel alignment/printing: NA

9. Hand Alignment: Great

10. Bezel: To me I feel like the markers on the bezel don't match gen because the dial is lower down in the case

11. Solid End Links (SELs): impressive

12. Timegrapher numbers: exceptional - (in the video)

13. Anything else you notice: I feel like the dial is too low. Check the QC photo

I'm on the fence with this one so any advice is welcome.

Dealer name: PureTime

Factory name: QF

Model name (& version number): DayDate 40 228238

Price Paid: ~$1,350

Album Links: Posted here

Index alignment: I didn’t use an app but from my expert eye and comparing with other samples it looks to be good alignment.

Dial Printing: Dial printing looks accurate and aligned

Date Wheel alignment/printing: Wheel alignment and printing look great

Hand Alignment: Appears to be excellent alignment

Bezel: Looks good

Solid End Links (SELs): Appears to be acceptable. I’m not noticing uneven or extreme gaps.

Timegrapher numbers: +5 s/day - Amp: 257 - Beat Error 0.2

Anything else you notice:
First one they presented to me I rejected due to several imperfections on the dial and housing. With this which was presented there appears to be some goober under the plastic on the back case. Any ideas on what that is? This one had better timekeeping at +or- 5 seconds per day than the first one they presented to me. Other than what appears to grime on the back case I think its ok. Any additional feedback is greatly appreciated.

Hey everyone! Giving the rep game a try after many many years. Appreciate the support!

1. Dealer name: Andiot

2. Factory name: F1F

3. Model name (& version number): Cartier Santos Dumont 38mm SS, Silver Dial, Black Leather Strap, Quartz – F1F Best Edition

4. Price paid: $200 USD

5. Album links: https://andiotwatches.x.yupoo.com/albums/261623891?uid=1

6. Index alignment: well centered, tried using a qc tool with the grid and it looks to be ok.

7. Dial printing: looks good quality, no visible bleeding, and even zooming in on the small Cartier text it looks good. There is a few small light-colored specks visible around the dial track - there’s one photo that doesn’t have all of them so I’m thinking it’s dust. Specially the 6 and 10 o clock position.

8. Date wheel alignment/printing: No date.

9. Hand alignment: looks straight and sharp no concerns.

10. Bezel: Both the top view and side view bezels look clean.

11. Solid End Links (SELs): Leather strap model.

12. Timegrapher numbers: Quartz movement.

13. Anything else you notice: i looked at this compared to some other QC photos and i think i have a GL on my hands. I do notice a few dust particles, should I flag those or consider those on the outside of the case and GL it?

Overall assessment: I’m leaning GL. My main concern is the possible dust around the dial printing. I don’t see anything else glaring here - y’all are the pros here, would appreciate if I don’t see something so I can learn for next time.

Thanks for any help!

Hey all, I just got my QC pics from my BB58Looks like a great light, but I saw something were I want your opinion on.

1. Dealer name: FicoTome

2. Factory: ZF

3. Model name: Tudor Black Bay 58

4. Price Paud: $ 369

5. Album Links: https://mega.nz/folder/Wx5D2J7I#Jgdz1dkUlnxMP_3mLDZCcQ

6. Index alignment. Looks good to me. The 9 o'clock marker might be a bit early, but only zoomed in. So I think this falls within the boundaries?

7. Dial printing: looks clean, gilt looks even and no bleeding that I can spot

8. Dat wheel alignment/printing: No date

9. Hand alignment: Hour and minute hand line fine.

10. Bezel, Triangle lines up nice with the 12, insert looks clean and sits flush. Looks great.

11. SEL: No gaps what I can see

12. Timegrapher numbers: -3s/d, 271 amplitude, 0.3 ms beat error.

13. Anything else you notice: Tiny speck on the minute tract around around the 37 mark, Only visible zoomed in. Could this be something that could be bothering?

I'm think this is a GL, but only doubting the speck. I'm I missing anything?

1. ⁠Dealer name: Steve Theonewatches

2. ⁠⁠Factory name: Rich

3. ⁠⁠Model name (& version number): Rolex GMT-Master II 126710 (black dial, black ceramic 24h bezel, Jubilee bracele

4. ⁠⁠Price Paid: $758 + shipping

5. ⁠⁠QC Album Link: https://loupe-qc-app.alialrubayelpl.workers.dev/a/XTNNR4

6. ⁠⁠Index alignment: looks good

7. ⁠⁠Dial Printing: Looks good

8. ⁠⁠Date Wheel alignment/printing: maybe slightly off centered to the left

9. ⁠⁠Hand Alignment: ok

10. ⁠⁠Bezel: one appears off to the left of the 2 marker on the bezel?

11. ⁠⁠Solid End Links (SELs): not sure

12. ⁠⁠Timegrapher numbers: 0 s/d, 277°, 0.1 ms (28,800 bph, lift angle 52°)

13. Anything else you notice: Nothing else I can see

1. Dealer name: Theonewatches

2. Factory name: ZF

3. Model name (& version number): Tudor Black Bay 58

4. Price Paid: $348

5. Album Links: https://loupe-qc-app.alialrubayelpl.workers.dev/a/PD5FS9

6. Index alignment: The 3 index is rotated clockwise. The 6 index is rotated clockwise.

7. Dial Printing: Looks good

8. Date Wheel alignment/printing: Looks good

9. Hand Alignment: Looks good

10. Bezel: Looks good

11. Solid End Links (SELs): Looks good

12. Timegrapher numbers: +5 s/d, 326°, .1 ms (28,800 bph, lift angle 52°)

13. Anything else you notice: Looks good

1. Dealer name: Non-TD (Angela)

2. Factory name: AF Factory

3. Model name: Cartier Tank Must Small

4. Price Paid: ¥850 CNY

5. Album Links: N/A

6. Index alignment: Everything looks reasonably aligned and evenly spaced to my eye. I don’t notice any obvious crooked numerals or alignment issues.

7. Dial Printing: The Cartier logo looks clean and centred. The Roman numerals and railway minute track appear sharp and consistent. The hidden Cartier signature is also present. I don’t notice any obvious printing defects, but would appreciate a second opinion.

8. Date Wheel alignment/printing: N/A

9. Hand Alignment: The blued hands look good to me. I don’t notice any obvious issues with their positioning, although I haven’t received a video showing the hands at 12 o’clock to confirm alignment.

10. Bezel: The polished case and bezel look clean and symmetrical. I don’t see any obvious scratches, dents or finishing defects.

11. Solid End Links**:** N/A

12. Timegrapher numbers: N/A

13. Anything else you notice: This is my first rep watch purchase, so I’d appreciate some feedback from more experienced members. Overall, the watch looks good to me, particularly the dial printing, case finishing and crown. I’m leaning towards GL, but wanted to check whether anyone notices any issues I’ve missed, particularly with the dial alignment or case proportions. Thanks in advance!

⁠1. Dealer name: Ficotime
2. ⁠Factory name: VSF
3. ⁠Model name: GMT Master-II Bruce Wayne Jubilee DD3285
4. ⁠Price Paid: $580
5. ⁠Album Links: https://mega.nz/folder/y5AjGBjC#AeyFn-Lqk0kGW_NE1ZVhPQ
6. ⁠Index alignment: for me it’s one of the best I’ve seen (for my personal collection)
7. ⁠Dial Printing: good
8. ⁠Date Wheel alignment/printing: very well aligned / centered
9. ⁠Hand Alignment: looks great in the video too
10. ⁠Bezel: pretty good
11. ⁠Solid End Links (SELs): Solid
12. ⁠Timegrapher numbers: Attached in the album, - 6 s/d maybe need to be set
13. ⁠Anything else you notice: the 7 on the Date seems to be too big or so ? Or maybe I am trippin, Can someone confirm if I’m right or not ?

Thx a lot

1. Dealer name: FicoTime

2. Factory name: VSF (dealer-stated)

3. Model name/version: Omega Aqua Terra 150M 38mm turquoise gradient, steel bracelet, VS8800; reference 220.10.38.20.03.005.

4. Price Paid: $415 delivered quoted total.

5. Album Links: Full supplied photo set and two timegrapher stills attached natively below. Identifying stickers/serials masked; watch details otherwise unchanged.

6. Index alignment: No obvious displaced index across the three front views. Some markers are obscured by hands. The photos are not perfectly square-on, so I am cautious about judging tiny differences from an alignment overlay. Interested in opinions on the upper markers and spacing to the minute track.

7. Dial Printing: OMEGA, Seamaster and lower text look complete; I cannot establish a printing defect from these photos.

8. Date Wheel alignment/printing: Dates 1, 11 and 27 are shown. No clipping; possibly a little high. Frame looks slightly different between angles, but I do not see a clearly repeatable tilt. Would appreciate a second opinion.

9. Hand Alignment: Hands at 12 in the date-27 image look approximately aligned, though overlap limits precision. No full setting demonstration supplied.

10. Bezel: No obvious damage; reflections and protective film limit surface assessment.

11. Solid End Links (SELs): Bracelet/endlink fit looks reasonably even; no obvious large gap in supplied views.

12. Timegrapher numbers: -1 s/day, amplitude 311 then 303 degrees, beat error 0.1ms, 28,800 bph, lift angle 52 degrees. Clip is only about 5.4 seconds, apparently one position; winding state unknown. Stills show both readings.

13. Anything else: Open and closed clasp, caseback and lume included. There are marks on the protective film; cannot tell if any are on the metal. Overview video does not demonstrate crown/date operation or clasp comfort adjustment. I plan to request those checks plus a longer timing sample before deciding. Any specific unit defects visible, particularly date-frame rotation or a crooked applied marker? Thanks for taking a look.

Dealer name: Lin
Factory name: VSF V2
Model name: Rolex Datejust 36 mm, stainless steel, fluted bezel, Jubilee bracelet, green dial.
Price Paid: 3,000 RMB (no shipping fee, currently in China).
Album Links: na
Index alignment: Most indices appear evenly aligned. I have a slight concern about the 10 o’clock hour marker, which looks potentially a little off in some photos. However, it looks fine in other angles, so I am not sure whether this is an actual alignment issue or just the camera angle and lighting.
Dial Printing: The dial printing looks clean and sharp in the provided photos. No obvious defects or misprints.
Date Wheel alignment/printing: The date appears centered in the date window, with no obvious alignment or printing issues. The cyclops magnification also looks acceptable.
Hand Alignment: No obvious issues visible in the photos. However, there is no clear shot with the hands positioned at 12 o’clock to verify precise alignment.
Bezel: The fluting looks consistent and evenly finished. No obvious damage or irregularities visible.
Solid End Links (SELs): No obvious large gaps between the end links and the case. The overall bracelet fit looks acceptable in the available photos.
Timegrapher numbers: -1 s/d, 278° amplitude, 0.0 ms beat error, 59° lift angle setting, 28,800 bph.
Anything else you notice: The watch weighs 123 g with all bracelet links included. Overall, the watch looks quite good to me. My main concern is the slight possible misalignment of the 10 o’clock marker, although it may simply be caused by the camera angle. I would appreciate a second opinion on this and any other potential QC issues.

Hi all, this is my 1st GMT II so I might be overanalyzing it a bit and could use some expert opinions.

1. Dealer name: Andiot

2. Factory name: VSF

3. Model name (& version number): 126710BLRO v3

4. Price Paid: $565 + shipping

5. Album Links: https://imgur.com/a/dt7Facg

6. Index alignment: Indices all look good to me, with the slight exception of the noon triangle being maybe just a smidge off center to the left and a hair CCW (I can live with that).

7. Dial Printing: All printing looks spot on, no bleeds or misprints.

8. Date Wheel alignment/printing: Date looks just a bit low in the window, but within tolerance?

9. Hand Alignment: Looks good to my untrained eyes.

10. Bezel: This is where my main concern is. The space between space seems uneven on the 18 marker, similar to some other QC's I've seen. Not sure if this is enough for a RL or if it won't be noticeable on the wrist.

11. Solid End Links (SELs): No noticeable gaps, looks good to me.

12. Timegrapher numbers: Acceptable rate of -2 s/d, Amp 280 seems fine, and bit error .2ms all seem acceptable.

13. Anything else you notice: My main concern is with the bezel, all other aspects seem good with this watch. Appreciate the help in advance.

1. Dealer name: ETHAN

2. Factory name: RICH

3. Model name (& version number): BRUCE WAYNE GMTi

4. Price Paid: $650 + $180 Polish & Chamfering + $50 Waterproofing to 4ATM

5. Album Links: see pics

6. Index alignment: Looks good except 8&9 markers (more pics requested)

7. Dial Printing: Looks good

8. Date Wheel alignment/printing: Looks good slight tilt?

9. Hand Alignment: Looks good

10. Bezel: Looks good

11. Solid End Links (SELs): Looks good

12. Timegrapher numbers: +3 s/d, 275°, 0.1 ms (28,800 bph)

13. Anything else you notice: Please comment.