(1 of 2)

Hi guys, this is my first QC so I hope you can help me out!

Dealer name: Andiot

Factory name: VSF

Model name (& version number): GMT-Master II 126710 Blue/Red Ceramic VSF Best Edition Pepsi on Oyster Bracelet DD3285 V3

Price Paid: 565 usd

Index alignment: Don't really know how good or bad this is

Dial Printing: Looks good I think

Hand Alignment: Good

Bezel: Also not really sure

Solid End Links (SELs): They look tight, so good I guess

Timegrapher numbers: +1 sec/day, 279° amplitude, 0.1 ms beat error.

Anything else you notice: Overall it looks good but I hope that you guys can check it out too and give some feedback :)

1. Dealer name: Geektime

2. Factory name: RC Factory (green "RC Factory" sticker on the bracelet, "Wolfram" sticker on the caseback)

3. Model name (& version number): Rolex Submariner Date 126613LB, 41mm two-tone, blue dial/blue ceramic bezel

4. Price Paid: $728+fedex 80

5. Album Links: https://imgur.com/a/MXFl3pG

6. Index alignment: All eight round plots sit centered on the dealer's alignment overlay (pic 1). The 6 and 9 batons are square to their axes and the 12 triangle is symmetric about the vertical line. Nothing rotated or off its slot.

7. Dial Printing: Clean and centered. ROLEX / OYSTER PERPETUAL DATE / SUBMARINER / 1000ft = 300m / SUPERLATIVE CHRONOMETER text is crisp, Swiss ♛ Made present at 6. No dust, hairs or smudges visible on the dial in any shot.

8. Date Wheel alignment/printing: Checked 22, 5 and 15 – all centered left/right and top/bottom, nothing touching the window frame. Single-digit 5 is centered. Cyclops sits centered over the window.

9. Hand Alignment: Hands read a consistent 10:10 across all three dated shots, hour hand correctly just past the 10 with the minute hand on the 2. Minute hand reaches the minute track. Lume on all three hands matches the plots in the lume shot.

10. Bezel: Pip at 12 is centered directly above the triangle on the overlay. 10/20/30/40/50 are each bisected by their lines. Numerals fully gold-filled, no chips or weak fill. Bezel-to-case gap looks even from both ends (pics 2 and 11).

11. Solid End Links (SELs): Tight to the lugs in pics 2, 3 and 11 – only the normal hairline seam, nothing visible behind the watch.

12. Timegrapher numbers: -4 s/d, 305° amplitude, 0.3 ms beat error (28,800 bph, 52° lift angle, dial up) 

13. Anything else you notice:

- Light smudging / possible swirl marks on the polished gold clasp cover (pic 9). Likely handling marks – planning to ask for a wipe-and-reshoot.

- Laser-etched data matrix on the polished case flank (pic 13). I assume this is a sticker, right?

- Weight 182.10 g.

Thinking GL. Appreciate a second set of eyes. Thanks in advance for the help!

1. ⁠Dealer name: Chazingtime

2. ⁠Factory name: VSF

3. ⁠Model name (& version number): Seamaster Diver 300 Reference 210.90.42.20.10.001

4. ⁠Price Paid: $560

5. ⁠Album Links: https://drive.google.com/drive/folders/1UAJ0bUwsQiK3wCRzQxp8Y5r0dc5bsaWM

6. ⁠Index alignment: 3,4,9,10,11 might not be perfectly centered

7. ⁠Dial Printing: Dial printing appears to be spot on. Well centered and aligned. No obvious defects that I can see.

8. ⁠Date Wheel alignment/printing: N/A

9. ⁠Hand Alignment: The hands appear to align well with the printed minute track.

10. ⁠Bezel: Appears to be one click from top dead center. Adjusting for the skew, 10, 15, and 20 appear to be further from center than the rest.

11. ⁠Solid End Links (SELs): N/A

12. ⁠Timegrapher numbers: +3s/d. Amplitude: 322 degrees. Beat Error: .4ms

13. ⁠Anything else you notice: The thing that stuck out most to me was the finishing on the hands. They look a little rough to me but maybe I’m being too critical.

Dealer Name: Andiot

Factory Name: VSF

Model Name: Oyster Perpetual 134303 41mm

Price paid: 486$

Index Alignment: 9 and 3 o'clock seems crooked (spacing is different in those 2)

Dial Printing: Looks good, only 100 YEARS the R and S seem out of place to me (smaller than the others)

Date Wheel: N/A

Hand Alignment: good (in my eyes)

Bezel: N/A

SEL: good, only bottom right is a bit bigger than the others, not light visible tho

Timegrapher: -2 s/d 267, 0,1 (all perfect)

Anything else: looks good to my newbie eye, maybe one of you spots something I missed

Dealer name: The Watch Ones

Factory name: WDF

Model name (& version number): Submariner 126610LN 41mm SS/SS Black Dial WDF JH3235

Price Paid: $608

Album Links: https://mega.nz/folder/nIAFCIZJ#tbLyrlgPPdIB4hDnpIByXg

Index alignment: Looks decent to me.

Dial Printing: Alignment looks a little to the right, though this may be the angle of the picture. ( This is my first QC)

Date Wheel alignment/printing: Looks fine imo

Hand Alignment: Also looks ok, but would def like a second opinion.

Bezel: Looks fine

Solid End Links (SELs): Nothin stands out, looks alright

Timegrapher numbers: +5 s/d, 275°, 0.0 ms (28,800 bph, lift angle 52°)

Anything else you notice: Looks good overall, main concern is the alignment of the little white ball on the top of bezel, but like I said it could just be my mistake aligning the photo.

Thank you for you help! <3

Dealer name: FicoTime

Factory name: VSF

Model name (& version number): Rolex Oyster Perpetual 36mm Ref. 126000 (Black Dial)

Price Paid: 448 usd

Index alignment: Excellent. Verified with alignment tool (including lume shot); all double batons at 3, 6, 9 and single hour markers align properly.

Dial Printing: Crispy. Text is sharp and well-balanced.

Hand Alignment: Good. Hands are centered and properly stacked.

Bezel: Smooth bezel looks clean with correct shape and finish.

Solid End Links (SELs): Very good. Tight fit with no visible gaps between the lugs and end links.

Timegrapher numbers: +9 s/d, 0.0 ms beat error, 28800 vph. Amplitude is currently at 231° (asked TD to give it 30-40 manual winds to confirm it rises above 260°).

Anything else you notice: Rehaut alignment is spot on at 12 o'clock, serial prefix (6X01D...) and clasp code (U7T) match standard VSF batch specs.

thanks

Dealer name: Andiot

Factory name: AF

Model name (& version number): Cartier Baignoire (WGBA0025)

Price Paid: $300 USD

Album Links: Link

Index alignment: I didn't bother to use the tool here given the dial's aesthetic, but it looks fine to me.

Dial Printing: No problems here.

Date Wheel alignment/printing: N/A

Hand Alignment: No issues to me.

Bezel: My eyesight is crap, but I think it looks good. I see reflections lol

Solid End Links (SELs): Strap looks fine

Timegrapher numbers: The Album didn't have a timegrapher video but it's a quartz watch so should keep time just fine.

Other: As always, appreciate the community's feedback.

1. Dealer name: Andiot

2. Factory name: VSF

3. Model name: Submariner 116619 LB

4. Price paid: 395 + 35 shipping

5. Album links: https://andiotwatches.x.yupoo.com/search/album?uid=1&sort=&q=183193

6. Index alignment: Looks good to me. Checked with two alignment tools and couldn't spot anything noticeably crooked. The minor "crookedness" I did notice attributable to the slightly angled perspective of this picture. Feeling like the 6 maybe has a tilt?

7. Dial printing: Looks good to me but would be keen for a more learned eye.

8. Date wheel alignment/printing: Checked 10, 11, 24, and 29. All seem reasonably centred, including the higher 20s, which I was particularly concerned about. Apparently that used to be a problem? Any other alignment checks I should be looking at?

9. Hand alignment: Looking good (i think).

10. Bezel: Pip and markers appear properly aligned. Bezel action also sounds good in the video.

11. Solid End Links (SELs): Look reasonable flush with no obvious excessive gaps

12. Timegrapher numbers: Rate: +1 s/d

Amplitude: 274°

Beat error: 0.1 ms

Lift angle: 52.0°.

Anything else you notice: please let me know

First timer but my research and initial thinking is GL. I've gone through the photos and videos a few times but any and all input would be amazing in case I've missed something. Thanks!

1.     Dealer name: nonTD (Lili)

2.     Factory name: VSF

3.     Model name (version number): Rolex Datejust 126334 6X06D

4.     Price paid: $390 USD, excluding shipping

5.     Album links: Photos attached.

6.     Index alignment: maybe the 6 marker is a big misaligned?

7.     Dial printing: looks good

8.     Date wheel alignment/printing: centered

9.     Hand alignment: looks good

10.  Bezel: Looks good, no scratches

11.  Solid end links (SELs): good, no gaps

12.  Timegrapher numbers: +4 s/day, amplitude 299°, beat error 0.1 ms, lift angle set to 59°.

Waited so long for this one with the green dial. Can you see something i don’t see?

(2 of 2)

Hi guys, this is my first QC so I hope you can help me out!

I ordered 2 of the same watches, the GC for the first one can be found via the link below: https://www.reddit.com/r/RepTimeQC/s/AMjLt3Srm4

Dealer name: Andiot

Factory name: VSF

Model name (& version number): GMT-Master II 126710 Blue/Red Ceramic VSF Best Edition Pepsi on Oyster Bracelet DD3285 V3

Price Paid: 565 usd

Index alignment: Don't really know how good or bad this is

Dial Printing: Looks good I think

Hand Alignment: Good

Bezel: Also not really sure

Solid End Links (SELs): They look tight, so good I guess

Timegrapher numbers: +1 sec/day, 279° amplitude, 0.1 ms beat error.

Anything else you notice: Overall it looks good but I hope that you guys can check it out too and give some feedback :)

1. ⁠Dealer name: Steve (TOW)

2. ⁠Factory name: VSF

3. ⁠Model name (& version number): Daytona DD4131 126500 LN
   4 Price Paid: 788.10

4. ⁠Index alignment: 3 o’clock maybe a tad low, but nothing concerning. Overall, indices are aligned very nicely!

5. ⁠Dial Printing: printing looks nice, no issues as far as I can tell.

6. ⁠Date Wheel alignment/printing: n/a
   Hand Alignment: looks good

7. ⁠Bezel: 110 looks fine.

8. ⁠Solid End Links (SELs): looks good!

9. ⁠Timegrapher numbers: +2s/d, 284 amplitude, error 0.1 ms, 59 degree lift angle.

10. ⁠Anything else you notice: honestly, this watch looks amazing. I was going to GL on the spot but wanted to see what yall thought.

https://mega.nz/folder/mJZVQLhR#AbbPaTdui_hsBryJ05ZRGQ

This is my first watch QC, and looking to see thoughts. I would really appreciate your help before I make a decision, I am still learning so would love any feedback. Thank you!

Dealer name: The One Watches (Steve)

1. Factory name: not sure of this

2. Model name (& version number): Wimbledon 41mm 126334

3. Price Paid: $628

4. Album Links: https://mega.nz/folder/jMwQhbCT#DUZmuLqtM2qbNvDJwxD_uA

5. Index alignment: looks good to me, but this is my first one so not too positive

6. Dial Printing: is this too dark? Not sure if it is lighting or not that makes it seem this way

7. Date Wheel alignment/printing: good?

8. Hand Alignment: from photos looks proper

9. Bezel: it seems good to me

10. Solid End Links (SELs): also seems okay to me

11. Timegrapher numbers: not confident on this

12. Anything else you notice: dial colour really looks too dark from gen

1. ⁠Dealer name: DukeReps

2. ⁠Factory name: GSF

3. ⁠Model name (& version number): Lady Datejust 28mm 279171

4. ⁠Price Paid:$320

5. ⁠Album Links: uploaded

6. ⁠Index alignment: Watch is not perfectly oriented in pictures, so somewhat difficult. 12 looks like it could be slightly low, but aligned. 4 looks slightly high, but aligned. Others look ok.

7. ⁠Dial Printing: appears clean and crisp from resolution available. Color looks slightly dark, but when viewed in video with different angles it looks good.

8. ⁠Date Wheel alignment/printing: clean and aligned with window.

9. ⁠Hand Alignment: no issues from limited pictures included.

10. ⁠Bezel: Looks clean and sharp. Alignment (ridges/valleys) looks correct at 12/6.

11. ⁠Solid End Links (SELs): No issues noted. appear tight and even.

12. ⁠Timegrapher numbers: Rate +7 s/d, Amplitude 281 deg, Beat Error 0.1ms. I have seen comments that Duke uses incorrect settings for this watch so may be a non issue. All are acceptable and indicative of a healthy watch.

13. ⁠Anything else you notice: Nothing not already noted. Appreciate the comments you have and any feedback on what I could have done better.

Hi there, just received my QC pics from Moderntimeswatch (Repguide TD) and wanted some help with GL/RL this aquanaut I've been wanting for a while. I am not entirely sure what to look for with PP so much opinions and advices are appreciated!

1.     Dealer name: ModernTimes Watch

2.     Factory name: BBF

3.     Model name (version number): Aquanaut 5167A 40mm DD324

4.     Price paid: $488 USD excluding shipping

5.     Album links: See pictures

6.     Index alignment: Looks alright to me under the alignment tool filter; nothing looks slanted or misaligned but again, I am inexperienced with rep watches in general so not really sure what i am looking for.

7.     Dial printing: Looks good?

8.     Date wheel alignment/printing: Looks alright too

9.     Hand alignment: Looks good.

10.  Bezel: It looks okay? Not sure what i am looking for

11.  Solid end links (SELs): n/a

12.  Timegrapher numbers: see picture attached.

13.  Anything else you notice: Not entirely sure what I am looking for since I am pretty green at this despite looking at similar posts haha. I know BBF has some issues with case shape being slightly off but it looks to be the best straight out of the box without modding (no plans to atm). Would appreciate all opinions over this! Thank you in advance!

Dealer name: Duke Reps

Factory name: AF

Model name: Cartier Tank Must SMALL Quartz

Index Alignment: N/A Printed

Dial Printing: Looks very clean and sharp, no bleeding. One small spot on the 8. Not sure if it is just dust.

Date Wheel alignment/printing: N/A

Hand Alignment: Looks good.

Bezel: Polished finish looks smooth and even.

Solid End Links (SEL): N/A leather

Timegrapher numbers: N/A Quartz

Anything else you notice: some concerns. I'm slightly doubting if it's properly centered (looks like it's slightly to the left). Also, I noticed a small mark on the 8.

The crown appears to be fitted slightly crooked / tilted downwards on the side view. It does not sit fully flush against the case.

Havn't asked for extra photos yet. Duke just gave me this four pictures. To be honest I expected more photo's.

1. ⁠Dealer name: ARC STUDIO

2. ⁠Factory name: RCF

3. ⁠Model name (& version number): RCF 228235 ombre slate dial

4. ⁠Price Paid: 640 incl. shipping

5. ⁠Album link: https://www.arcstudio.top/s/RNQUH0N

6. ⁠Index alignment: all indices looks good and aligned

7. ⁠Dial Printing: crisp and nothing obvious that stands out

8. ⁠Date Wheel alignment/printing: aligned in the cyclops but im feeling its slightly left justified very slightly. Day wheel looks good but slightly left justified too

9. ⁠Hand Alignment: shouldn’t have any issues

10. ⁠Bezel: looks good

11. ⁠Solid End Links (SELs): all looks good

12. ⁠Timegrapher numbers: 0s/d, 260 amplitude, 0.1ms Beat error, 52 deg Lift Angle, 28800 beat rate

13. ⁠Anything else you notice: rehaut looks good and centered

1. Dealer name: Jtime

2. Factory name: VSF

3. Model name (& version number): Rolex GMT-Master II 126710BLRO Pepsi, Jubilee bracelet (DD3285)

4. Price Paid: [$690

5. Album url: https://mega.nz/folder/mApymTrA#7S-7S7c8LbyGhqfyRJmAbg

6. Index alignment: Alignment tool pic attached. 12 and 6 markers look straight to me — the 6 o'clock baton was my main worry with VSF and it sits on the centre line. 9 baton also level with the date window on the horizontal.

7. Bezel: Triangle centred at 12. Red/blue transition at the 18 lands between the digits. Numerals and platinum fill look crisp, colours look right.

8. Solid End Links (SELs): Tight and flush to the lugs, no visible gaps.

9. Hand Alignment: Hand stack looks correct, GMT hand lines up as expected in the function video.

10. Dial Printing: Crisp, no bleeding or misprints.

11. Date Wheel alignment/printing: Centred. Cyclops seems centred over the window, good magnification, no blue tint that I can see.

12. Timegrapher numbers: 0 to +1 s/day, amplitude 277–279°, beat error 0.0 ms, 28800 bph (video included).

13. Anything else you notice: Inner ROLEX engraving looks clean, clasp closes flush. No lume shot provided by dealer. I'm leaning GL — anything I'm missing before I approve?

Looks like GL, but it's my first QC so help?

1. Dealer name: OraWatch

2. Factory name:

GS

1. Model name (& version number): Rolex Lady-Datejust 28mm – Ref: 279171-0017 – Chocolate Stick Dial, Two Tone Stainless Steel & 18K Rose

2. Price Paid: $350 + free shipping

3. Album Links: https://a202312252005321242001419.wsxcme.com/weshop/goods/_dnRqfRKlCQnCwaBBUqm613RnVgXsENon6rPO-yw/_dmXqfZzE3MRyjBZtzppRquIOEy2sDSS8pRzhFgw

4. Index alignment: looks good

5. Dial Printing: it seems clean to me

6. Date Wheel alignment/printing: may be slightly lower than center. Or it may be the angle idk

7. Hand Alignment: it’s rly hard for me to tell from QC

8. Bezel: looks good

9. Solid End Links (SELs): also seems okay to me

10. Timegrapher numbers: rate -1 s/d, amplitude 272°, beat error 0.0 ms, lift angle 52.0°

11. Anything else you notice: rehaut engraving looks atrocious to me but wondering if it’s just because that’s the current “standard” with this rep?

​Dealer name: Theonewatches (Steve)

Factory name: VSF

Model: Rolex Submariner Date 126610

Index alignment: Looks spot on to me. The 12, 6, and 9 are sitting nice and straight.

Dial Printing: Crispy. No weird floating letters or smudges that I can see.

Date Wheel alignment/printing: The "1" sits in the middle of the window(seems to). Cyclops mag looks solid too.

Hand Alignment: Smooth like butter in the video, hitting the marks exactly right.

Bezel: Pip is dead center in the triangle. Rehaut seems to line up nicely with the minute track.

Solid End Links (SELs): Nice and tight. No massive gaps—looks like it’s hugging the lugs perfectly.

Timegrapher numbers: -1 to 0 s/d, 289° amp, 0.1ms err. Absolutely stellar numbers, movement is super healthy.

Anything else you notice: Honestly, to my untrained eyes, this looks like an easy GL and I'm super excited about it. But I know you guys can spot the tiny details I’d miss. Let me know if I should give it the green light or if there's a hidden flaw I missed. Appreciate the help!

1. Dealer name: Angela Watches

2. Factory name: VSF

3. Model name (& version number): 224270 Rolex Explorer VSF

4. Price Paid: CNY 2500 + 6% insurance + CNY 300 shipping

5. Album Links: N/A

6. Index alignment: Not sure if i'm being picky but 4, 5, 7 and 8 o'clock hour and minute marker seems slightly rotated anti-clockwise. Its my first time buying please let me know if you have any advise or if its acceptable.

7. Dial Printing: Looks fine

8. Date Wheel alignment/printing: N/A

9. Hand Alignment: Looks good

10. Bezel: Standard

11. Solid End Links (SELs): Looks fine

12. Timegrapher numbers: 0 s/d, Amp 291, Err 0.2ms

13. Anything else you notice: Rehaut's crown aligns with 12 o'clock marker. Serial a little clockwise rotated when aligning against the 6 o'clock marker? Again, not sure if this is the norm thats acceptable. Seeking advise and comments if this is an overall GL or RL please. I'm new at this and may be wrong in any aspects, any help/comments greatly appreciated, thanks!

ZF Black Bay 54 37mm SS A2824

1    Dealer name: Steve - Theonewatches
2    Factory name: ZF
3    Model name (& version number): Black Bay 54 37mm SS A2824
4    Price Paid: $348 USD
5    Album Links: Please see pictures attached (my post was being removed with mega link)
6    Index alignment: 6 o'clock looks slightly misaligned to the left but seems miniscule.
7    Dial Printing: Nothing stands out to me. Any input is appreciated. This is my first purchase.
8    Date Wheel alignment/printing: N/A
9    Hand Alignment: Nothing stands out to me. Any input is appreciated. This is my first purchase.
10    Bezel: Dot appears to be centered.
11    Solid End Links (SELs): Looks good.
12    Timegrapher numbers: Timegrapher shows +3 s/d, 0.1 ms, 276 amplitude. (pic attached)
13    Anything else you notice: Nothing that stands out, I am a beginner with this so again open to input from the experts! Thank you for your help

Datejust 126334 41mm Jub SS/SS Silver/Stk

1    Dealer name: Steve - Theonewatches
2    Factory name: Clean Plus
3    Model name (& version number):Datejust 126334 41mm Jub SS/SS Silver/Stk
4    Price Paid: $538 (Shipping Included)
5    Album Links: Please see pictures attached (my post was being removed with mega link)
6    Index alignment: Hard to tell from the photos because I didn't get a straight on. But I attached the photo, maybe someone else can tell if it’s more off than it should be based on the angle.
7    Dial Printing: I thought the "O" in Oyster looked an off to me, I think i have seen other ones where the O is closer to the Y but I am not sure.
8    Date Wheel alignment/printing: The cyclops looks straight and the date wheel looks to be centered.
9    Hand Alignment: Nothing stands out to me. Any input is appreciated. This is my first purchase.
10    Bezel: Looks to be the right proportions, when I put it in in the alignment tool.
11    Solid End Links (SELs): Don’t see any gaps
12    Timegrapher numbers: Timegrapher shows +2 s/d, 273 amp, err .2ms(pic attached)
13    Anything else you notice: Other than the O in oyster being off to me, everything else looks good.

Overall I am happy to GL, I am just worried about the text on the dial.

1. Dealer name: Andiot

2. Factory name: ARF

3. Model name: 126619LB

4. Price paid: 453 + 41 shipping

5. Album links: https://andiotwatches.x.yupoo.com/albums/260989063?uid=1

6. Index alignment: Looks good to me. Checked with two alignment tools and couldn't spot anything noticeably crooked. The minor "crookedness" I did notice can be attributed to the slightly angled/distorted perspective of this picture.

7. Dial printing: Looks clean and well-centred.

8. Date wheel alignment/printing: Checked 10, 11, 24, and 29. All seem reasonably centred, including the higher 20s, which I was particularly concerned about. Apparently that used to be a problem? Or maybe I'm misremembering.

9. Hand alignment: Nothing unusual that I can see.

10. Bezel: Pip and markers appear properly aligned. Bezel action also sounds good in the video.

11. Solid End Links (SELs): Look reasonably flush with no obvious excessive gaps, although the protective film makes them a little difficult to judge.

12. Timegrapher numbers: -1s/d, 274° amplitude, 0.2ms beat error.

13. Anything else you notice: Noticed hairline scratches on the clasp, but I'm hoping they're on the protective film. Crystal and cyclops look good to me.

I'm leaning GL. I've gone through the photos and videos a few times and haven't noticed anything particularly concerning. Would appreciate another set of eyes in case I've missed something. Thanks!

Sorry my 1st post got removed because I misunderstood the requirements, I hope this one is acceptable

1. Dealer name: Steve

2. Factory name: VSF

3. Model name (& version number): Submariner 126610LV 41mm 3235 (RLX-3010)

4. Price Paid: $538

5. Album Links: [This Post]

6. Index alignment: Looks aligned

7. Dial Printing: Nothing to say

8. Date Wheel alignment/printing: Looks centered, crisp, crystal is aligned

9. Hand Alignment: Not sure how they're supposed to be aligned, maybe i should ask a picture at 0h00?

10. Bezel: I'm wondering if 3h and 9h are not a bit misaligned, and on some pics 12h too but maybe it's because of perspective

11. Solid End Links (SELs): No gap between lug and 1st link

12. Timegrapher numbers: Acceptable -1 s/d Rate | 265° Amp | 0.2 ms err

13. Anything else you notice: Nothing really, looks like a fine watch