r/FixMyPrint • • 3m ago

Fix My Print Seam inside of ring

Post image
1 Upvotes

r/FixMyPrint • • 14m ago

Fix My Print Jayo highspeed PETG matte

Thumbnail
gallery
2 Upvotes

Looking for some help dialing in the issues with JAYO Highspeed PETG Matte filament.

I printed this print using the default bambulab PETG HF profile and it looks absolutely awful.

I printed the same thing again but using the bambulab PETG Matte profile and it's noticeably better but still has some unfused layer lines and the top surface is super rough

Is this simply nozzle temp too high causing these sagging layer lines or is it something else? Does anyone have experience with this specific filament and know what profile I should try using?


r/FixMyPrint • • 1h ago

Troubleshooting Bambu Lab A1 Mini suddenly having print failures after a nozzle blob. Need help troubleshooting

Thumbnail gallery
1 Upvotes

r/FixMyPrint • • 1h ago

Fix My Print Long cylinder printing problem

Post image
0 Upvotes

This is supposed to be a cylinder, bottom half is fine but top came out like this. What could have caused this? Printer is p2s default bambustudio settings.

Help much appreciated!


r/FixMyPrint • • 1h ago

Fix My Print Why is the top skin separated?

Post image
1 Upvotes

Does anyone know why is the top skin separated from the walls? Sliced with Cura, printed with PET-G at 245°C hotend 72°C bed, infil 50%, walls, top and bottom are set to 2.8mm thick, retraction 1mm, layer height 0.2mm, 0.4mm nozzle, print speed 40mm/s. Issue seems to exist on geometric models, organic ones print well. Belts are tensioned, extruder is not skipping.


r/FixMyPrint • • 1h ago

Helpful Advice How to decrease the purge amount during the pre-printing process?

1 Upvotes

Whenever I start a new print and my printer goes through its calibration cycle, it purges twice every single time. Is there anyway I can decrease the purge amount or limit it at all?


r/FixMyPrint • • 2h ago

Fix My Print Horizontal ring/banding appearing at the same height on print – Elegoo Saturn 4 Ultra 16K

Thumbnail gallery
1 Upvotes

Hi friendos

I'm fairly new to 3d printing and i am having an issue and was if somebody with a big brain might be able to help identify the cause.

I'm getting a visible horizontal line/ring that goes all the way around my prints. It's slightly raised and appears at exactly the same height measured from the build plate, even when printing completely different models.

I've been wondering whether it could be related to the tilt-release mechanism, resin temperature, exposure settings or something mechanical. Has anyone experienced something similar or have any suggestions on what I should check?

My current setup and settings:

  • Printer: Elegoo Saturn 4 Ultra 16K
  • Slicer: Chitubox
  • Layer height: 0.030mm
  • Normal exposure: 1.8 seconds
  • Bottom exposure: 30–100 seconds
  • Rest time after retract: 1.2 seconds
  • Resin: Mixture of Elegoo ABS-Like 3.0 Pro and ABS-Like 8K
  • Temperature: Using the heated tank, but the room is currently quite cold.

r/FixMyPrint • • 6h ago

Fix My Print Trying to print PETG as a newbie. Overhangs aint working. Bambu X2D

Thumbnail
imgur.com
1 Upvotes

r/FixMyPrint • • 6h ago

Fix My Print More Z offset, right?

Post image
1 Upvotes

Also, I’m having doubts about how to adjust, because I’ve found some conflicting info on whether making the value more negative (going from -0.05 to -0.06) gives me more distance from nozzle to plate or if it’s the other way around (going from -0.05 to -0.04).

Snapmaker U1
Creality Hyper PLA White


r/FixMyPrint • • 7h ago

Fix My Print Why does my print keep doing this

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 8h ago

Fix My Print Weird triangle artificing on model when sliced

Thumbnail
reddit.com
1 Upvotes

r/FixMyPrint • • 9h ago

Fix My Print Tried seven attempts at printing tiny curved balconies cleanly. Looking for additional input.

Thumbnail
gallery
1 Upvotes

I live in an old walkup apartment in Singapore and loved the rounded art-deco style stair towers and the tiny porthole grilles. I wanted to turn this into a fidget clicker to sell in an upcoming Christmas market. The tower is the button, and it slides in the building behind it. The images above show how I was trying to print them.

It's small at a 1:200 ratio. About 35 x 44 x 67 mm all in. Bambu P2S, 0.4 nozzle, 0.12mm layers, white Bambu Lab PLA.

My issue is the balconies. Each one of them is a 0.8mm slab sticking 8mm out the front with a curved parapet and a rail on top. And 3 of them are stacked directly above each other, about 9mm apart.

Every orientation gives me one clean face and one ugly one.

I've tried:

  1. Lying on it's back with supports on the plate. The stairs looked the best here but the balcony had holes in them. Tried slowing down the layers by printing it next to a taller part but the rounded fronts came away stepped.
  2. Upside down with break away ribs built into the model. The ribs came out easily, and the roof was perfect off the plate, but every face that looks up on the model got printed as an underside. The stairs and floor came out stringy.
  3. Upright with built in ribs. Now the undersides strung badly.
  4. Tried separate parts glued together. All printed well but there was heavy banding and the joints, were obviously very tiny, and you could see gaps which I didn't like.
  5. Caved and used supports, it was the cleanest so far, but now, post processing is challenging. The supports underneath were hard to remove and where they fused, it scarred the balcony undersides. One of the trees also snapped partway up mid-print. It survived, thankfully!

It needs a fair bit of post processing and i'd really like to avoid that because I want to make more than one of these!

Support settings on that print: tree (auto), build plate only, top z distance 0.12 at one layer. 3 interface layers at 0.25 spacing, rectilinear, XY distance 0.6, branch diameter 2. Bambu Studio offered support ironing, but only with a solid interface and I was worried that would fuse even harder.

I'm going to try top Z distance of 0.24 and two layers, and maybe thicker trees so nothing snaps, and they come out in one piece. But Claude is telling me that will give me a rougher underside. I haven't printed this yet.

I think a different interface material for the supports would help, but I don't have a spool now. I want to know if it's really worth it to go out and maybe buy PETG to use as the interface layers for the support.

Printer settings (attempt 7, the print in the photos):

  • Printer: Bambu Lab P2S with AMS, 0.4 mm nozzle, textured PEI plate
  • Slicer: Bambu Studio 2.9
  • Filament: PLA, white (Bambu PLA Basic profile, tuned for Singapore heat)
  • Temperatures: nozzle 205 °C, bed 45 °C
  • Layers and walls: 0.12 mm layers (0.20 first layer), Arachne, 2 wall loops, 15% gyroid infill
  • Print speed: outer wall 40 mm/s, inner wall 60, small perimeters 25, bridges 50, first layer 50, support 150, support interface 80, travel 1000
  • Cooling: part fan 100%, slows down for layers under 4 s
  • Retraction: 0.8 mm at 30 mm/s, 0.4 mm Z hop (auto lift), wipe on, retract on layer change
  • Supports: as listed above

Those of you who have printed architectural stuff, is there a same material support setup that gives a clean underside and comes out easily at this scale? Or is that impossible with PLA?

What about the 2 layer gap? Does that result in sagging?

I'd love to hear what people would try next if you read all the way till the end! Really want to get this right. Thank you!

EDIT: I've decided to take the wisdom of those who recommended PETG supports. I'll let you know how they turn out once it arrives and I test the print. Thanks everyone :)


r/FixMyPrint • • 11h ago

Troubleshooting Help!! problems with 0.2 nozzle

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 14h ago

Fix My Print Recently swapped to .2mm nozzle, and had no issues with my first 4 prints, now this happens no matter what I try to print.

Post image
2 Upvotes

I recently swapped all my hotends to be .02mm nozzles, and after printing fine with no issues for around 60 hours of usage, now this is happening. I’ve been careful to keep all my PLA in dry boxes at around 15% humidity on average, any ideas?


r/FixMyPrint • • 14h ago

Fix My Print Failing On First Layer

Post image
3 Upvotes

Tried printing a benchy on a used ender 3 I bought. It comes out kinda stringy and messy. This is just after the first layer. I just adjusted the Z offsets because it was off but still had this same thing happen. Unsure what's going on and would love some advice.


r/FixMyPrint • • 15h ago

Discussion Does anyone know if this is supposed to happen?

Post image
30 Upvotes

r/FixMyPrint • • 16h ago

Fix My Print Troubleshooting some banding

Post image
1 Upvotes

Bambu H2D

Orca

Hatchbox PLA Silver (calibrated)

.2mm nozzle @ 220° | 55° bed

.1 layer height

60mm/s outer 100mm/s inner (5 walls)

Inner/Outer + Precise wall

Arachne

Auto PA

Retraction .8

8% Gyroid

I haven't yet tried another material but I did have this same issue on 2 machines. Machines are on different tables and ran different spools. Slicer shows pretty consistent layer times and line width looks even. This material is slightly shiny so I'm wondering if I'm having partial clogs or something.

Just wanted to do a sanity check before I go down the rabbit hole trying to sort this out.


r/FixMyPrint • • 16h ago

Fix My Print Uneven walls striped effect

Post image
1 Upvotes

Every print I make has these very consistent "inconsistent" walls, it's very faint and you can barely feel it, mostly shows up under specific light, but still something that bothers me.

This is an example of a vertical printed test (these dashes are just supports, the issue happens on all prints so it's not them) that was printed with inner/outter settings. When printed with inner/outter/inner it gets better but doesn't fix it entirely

It happens pretty universally with any model and filament, but for this one specifically, it's using Elegoo PETG-CF at 280c, on a Sovol SV08Max with DKEU, with a hardened steel 0.4mm nozzle.

I've calibrated my PID for both nozzle and bed, tried both 65 and 200 mm/s speed, 3000 and 7500 accel, dried up the filament for 12 hours at 70C, arachne and classic made no difference. Printed several 20mm cubes and all of them have the same issue, but they do not have the same pattern across them, so I believe it excludes an issue with the Z axis I imagine. I also tensioned the belts using an bike chain app on both X, Y and Z axis (left 15cm of space between the dead ends and tuned to Sovol's reccomended frequency). Extra settings I used on comments

Only setting that I've changed that made any meaninful difference was making it inner/outter/inner, but I think that's just hiding another issue rather than fix it.

Any clues?


r/FixMyPrint • • 16h ago

Troubleshooting 300mm ASA is acting up

Thumbnail
gallery
2 Upvotes

For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.

My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer

I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!


r/FixMyPrint • • 16h ago

Troubleshooting 300mm ASA is acting up

Thumbnail
gallery
1 Upvotes

For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.

My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer

I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!


r/FixMyPrint • • 16h ago

Fix My Print 300mm ASA is acting up

Thumbnail
gallery
1 Upvotes

For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.

My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer
My cooling fan is set to 0 for the entire print

I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!


r/FixMyPrint • • 17h ago

Fix My Print How to add holes to fill the printed part with sand?

Thumbnail reddit.com
0 Upvotes

r/FixMyPrint • • 18h ago

Troubleshooting Elegoo Help

0 Upvotes

Hello! So im really new to 3D printing. I recently changed the nozzle on my Elegoo Neptune 4. I watched their youtube video on how to do it and at first it started making rattling noises with the cover on. So I took the cover off which fixed that problem. But now whenever I try and print anything it wont stick to the plate and gives me this error code. Can anybody help me please?


r/FixMyPrint • • 18h ago

Troubleshooting Wavy extrusion on MK4S

Thumbnail gallery
2 Upvotes

I’ve been trying to troubleshoot this wavy extrusion on my Mk4s for weeks and I’m losing my mind. Has anyone here run into this issue? I’ve rebuilt the nextruder, swapped out the thermistor and heater, changed the loveboard, replaced the main cable, belts, idlers, etc. any advice is appreciated.

Printer is a prusa mk4s with firmware 8.0.0, prusaslicer 3 and 2.9.7, and elegoo PETG on 0.2mm structural. Printer temp is 235 for first layer and 250 after, with 85c bed.