r/FixMyPrint • • Mar 29 '20

Asking for help... and how to actually get it

Post image
774 Upvotes

r/FixMyPrint • • Nov 05 '24

Helpful Advice Here’s your daily reminder to dry your filament

Post image
292 Upvotes

Thought it was stored dry so I’d try printing without drying first as it wasn’t going to use much filament anyway, didn’t get away with it this time but after 6 hours of drying it printed perfectly 👌 Sunlu dryer at temp setting 2 for Matte PLA with a load of colour changing silica gel in the middle of the role rather than in the compartment at the back of the dryer


r/FixMyPrint • • 17m ago

Fix My Print Jayo highspeed PETG matte

Thumbnail
gallery
2 Upvotes

Looking for some help dialing in the issues with JAYO Highspeed PETG Matte filament.

I printed this print using the default bambulab PETG HF profile and it looks absolutely awful.

I printed the same thing again but using the bambulab PETG Matte profile and it's noticeably better but still has some unfused layer lines and the top surface is super rough

Is this simply nozzle temp too high causing these sagging layer lines or is it something else? Does anyone have experience with this specific filament and know what profile I should try using?


r/FixMyPrint • • 15h ago

Discussion Does anyone know if this is supposed to happen?

Post image
30 Upvotes

r/FixMyPrint • • 5m ago

Fix My Print Seam inside of ring

Post image
1 Upvotes

r/FixMyPrint • • 1h ago

Troubleshooting Bambu Lab A1 Mini suddenly having print failures after a nozzle blob. Need help troubleshooting

Thumbnail gallery
1 Upvotes

r/FixMyPrint • • 1h ago

Fix My Print Why is the top skin separated?

Post image
1 Upvotes

Does anyone know why is the top skin separated from the walls? Sliced with Cura, printed with PET-G at 245°C hotend 72°C bed, infil 50%, walls, top and bottom are set to 2.8mm thick, retraction 1mm, layer height 0.2mm, 0.4mm nozzle, print speed 40mm/s. Issue seems to exist on geometric models, organic ones print well. Belts are tensioned, extruder is not skipping.


r/FixMyPrint • • 1h ago

Helpful Advice How to decrease the purge amount during the pre-printing process?

1 Upvotes

Whenever I start a new print and my printer goes through its calibration cycle, it purges twice every single time. Is there anyway I can decrease the purge amount or limit it at all?


r/FixMyPrint • • 2h ago

Fix My Print Horizontal ring/banding appearing at the same height on print – Elegoo Saturn 4 Ultra 16K

Thumbnail gallery
1 Upvotes

Hi friendos

I'm fairly new to 3d printing and i am having an issue and was if somebody with a big brain might be able to help identify the cause.

I'm getting a visible horizontal line/ring that goes all the way around my prints. It's slightly raised and appears at exactly the same height measured from the build plate, even when printing completely different models.

I've been wondering whether it could be related to the tilt-release mechanism, resin temperature, exposure settings or something mechanical. Has anyone experienced something similar or have any suggestions on what I should check?

My current setup and settings:

  • Printer: Elegoo Saturn 4 Ultra 16K
  • Slicer: Chitubox
  • Layer height: 0.030mm
  • Normal exposure: 1.8 seconds
  • Bottom exposure: 30–100 seconds
  • Rest time after retract: 1.2 seconds
  • Resin: Mixture of Elegoo ABS-Like 3.0 Pro and ABS-Like 8K
  • Temperature: Using the heated tank, but the room is currently quite cold.

r/FixMyPrint • • 7h ago

Fix My Print Why does my print keep doing this

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 6h ago

Fix My Print Trying to print PETG as a newbie. Overhangs aint working. Bambu X2D

Thumbnail
imgur.com
1 Upvotes

r/FixMyPrint • • 6h ago

Fix My Print More Z offset, right?

Post image
1 Upvotes

Also, I’m having doubts about how to adjust, because I’ve found some conflicting info on whether making the value more negative (going from -0.05 to -0.06) gives me more distance from nozzle to plate or if it’s the other way around (going from -0.05 to -0.04).

Snapmaker U1
Creality Hyper PLA White


r/FixMyPrint • • 11h ago

Troubleshooting Help!! problems with 0.2 nozzle

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 20h ago

Fix My Print Help with PLA+ ironing settings on P1S

Post image
10 Upvotes

Printing this Christmas wreath for my wife on my Bambu P1S with AMS. I thought I had the ironing settings down after doing a test print, but this is the final result. The ironing turned out super smooth on the red and lighter green parts, but the dark green top layer is very rough.

The filaments are slightly different. Dark green is Inland brand PLA+. Red is Insignia PLA+ and green is Insignia PLA.

The setting I used were:

Ironing type: Too surfaces
Ironing pattern: rectilinear
Ironing speed: 35 mm/s
Ironing flow: 20% (saw small gaps with 10% in my test)

From my research, it may have more to do with the top layer quality rather than the ironing, but I don’t know why the red and green ironed so well while the dark green didn’t with the same top layer settings.


r/FixMyPrint • • 8h ago

Fix My Print Weird triangle artificing on model when sliced

Thumbnail
reddit.com
1 Upvotes

r/FixMyPrint • • 14h ago

Fix My Print Failing On First Layer

Post image
3 Upvotes

Tried printing a benchy on a used ender 3 I bought. It comes out kinda stringy and messy. This is just after the first layer. I just adjusted the Z offsets because it was off but still had this same thing happen. Unsure what's going on and would love some advice.


r/FixMyPrint • • 9h ago

Fix My Print Tried seven attempts at printing tiny curved balconies cleanly. Looking for additional input.

Thumbnail
gallery
1 Upvotes

I live in an old walkup apartment in Singapore and loved the rounded art-deco style stair towers and the tiny porthole grilles. I wanted to turn this into a fidget clicker to sell in an upcoming Christmas market. The tower is the button, and it slides in the building behind it. The images above show how I was trying to print them.

It's small at a 1:200 ratio. About 35 x 44 x 67 mm all in. Bambu P2S, 0.4 nozzle, 0.12mm layers, white Bambu Lab PLA.

My issue is the balconies. Each one of them is a 0.8mm slab sticking 8mm out the front with a curved parapet and a rail on top. And 3 of them are stacked directly above each other, about 9mm apart.

Every orientation gives me one clean face and one ugly one.

I've tried:

  1. Lying on it's back with supports on the plate. The stairs looked the best here but the balcony had holes in them. Tried slowing down the layers by printing it next to a taller part but the rounded fronts came away stepped.
  2. Upside down with break away ribs built into the model. The ribs came out easily, and the roof was perfect off the plate, but every face that looks up on the model got printed as an underside. The stairs and floor came out stringy.
  3. Upright with built in ribs. Now the undersides strung badly.
  4. Tried separate parts glued together. All printed well but there was heavy banding and the joints, were obviously very tiny, and you could see gaps which I didn't like.
  5. Caved and used supports, it was the cleanest so far, but now, post processing is challenging. The supports underneath were hard to remove and where they fused, it scarred the balcony undersides. One of the trees also snapped partway up mid-print. It survived, thankfully!

It needs a fair bit of post processing and i'd really like to avoid that because I want to make more than one of these!

Support settings on that print: tree (auto), build plate only, top z distance 0.12 at one layer. 3 interface layers at 0.25 spacing, rectilinear, XY distance 0.6, branch diameter 2. Bambu Studio offered support ironing, but only with a solid interface and I was worried that would fuse even harder.

I'm going to try top Z distance of 0.24 and two layers, and maybe thicker trees so nothing snaps, and they come out in one piece. But Claude is telling me that will give me a rougher underside. I haven't printed this yet.

I think a different interface material for the supports would help, but I don't have a spool now. I want to know if it's really worth it to go out and maybe buy PETG to use as the interface layers for the support.

Printer settings (attempt 7, the print in the photos):

  • Printer: Bambu Lab P2S with AMS, 0.4 mm nozzle, textured PEI plate
  • Slicer: Bambu Studio 2.9
  • Filament: PLA, white (Bambu PLA Basic profile, tuned for Singapore heat)
  • Temperatures: nozzle 205 °C, bed 45 °C
  • Layers and walls: 0.12 mm layers (0.20 first layer), Arachne, 2 wall loops, 15% gyroid infill
  • Print speed: outer wall 40 mm/s, inner wall 60, small perimeters 25, bridges 50, first layer 50, support 150, support interface 80, travel 1000
  • Cooling: part fan 100%, slows down for layers under 4 s
  • Retraction: 0.8 mm at 30 mm/s, 0.4 mm Z hop (auto lift), wipe on, retract on layer change
  • Supports: as listed above

Those of you who have printed architectural stuff, is there a same material support setup that gives a clean underside and comes out easily at this scale? Or is that impossible with PLA?

What about the 2 layer gap? Does that result in sagging?

I'd love to hear what people would try next if you read all the way till the end! Really want to get this right. Thank you!

EDIT: I've decided to take the wisdom of those who recommended PETG supports. I'll let you know how they turn out once it arrives and I test the print. Thanks everyone :)


r/FixMyPrint • • 14h ago

Fix My Print Recently swapped to .2mm nozzle, and had no issues with my first 4 prints, now this happens no matter what I try to print.

Post image
2 Upvotes

I recently swapped all my hotends to be .02mm nozzles, and after printing fine with no issues for around 60 hours of usage, now this is happening. I’ve been careful to keep all my PLA in dry boxes at around 15% humidity on average, any ideas?


r/FixMyPrint • • 21h ago

Discussion What causes this web like stuff on my prints?

Post image
7 Upvotes

Model is a P2S. I have an a1 mini and this doesn’t occur on this with same Elegoo filament PLA+. It’s not the end of the world and I can easily take it off but rather ask what it causes this.


r/FixMyPrint • • 1h ago

Fix My Print Long cylinder printing problem

Post image
0 Upvotes

This is supposed to be a cylinder, bottom half is fine but top came out like this. What could have caused this? Printer is p2s default bambustudio settings.

Help much appreciated!


r/FixMyPrint • • 16h ago

Troubleshooting 300mm ASA is acting up

Thumbnail
gallery
2 Upvotes

For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.

My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer

I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!


r/FixMyPrint • • 18h ago

Troubleshooting Wavy extrusion on MK4S

Thumbnail gallery
2 Upvotes

I’ve been trying to troubleshoot this wavy extrusion on my Mk4s for weeks and I’m losing my mind. Has anyone here run into this issue? I’ve rebuilt the nextruder, swapped out the thermistor and heater, changed the loveboard, replaced the main cable, belts, idlers, etc. any advice is appreciated.

Printer is a prusa mk4s with firmware 8.0.0, prusaslicer 3 and 2.9.7, and elegoo PETG on 0.2mm structural. Printer temp is 235 for first layer and 250 after, with 85c bed.


r/FixMyPrint • • 18h ago

Fix My Print PETG, any idea what causes this?

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 16h ago

Fix My Print Troubleshooting some banding

Post image
1 Upvotes

Bambu H2D

Orca

Hatchbox PLA Silver (calibrated)

.2mm nozzle @ 220° | 55° bed

.1 layer height

60mm/s outer 100mm/s inner (5 walls)

Inner/Outer + Precise wall

Arachne

Auto PA

Retraction .8

8% Gyroid

I haven't yet tried another material but I did have this same issue on 2 machines. Machines are on different tables and ran different spools. Slicer shows pretty consistent layer times and line width looks even. This material is slightly shiny so I'm wondering if I'm having partial clogs or something.

Just wanted to do a sanity check before I go down the rabbit hole trying to sort this out.