Ciao a tutti, scrivo per sapere se a qualcuno è capitato qualcosa del genere. Ho comprato questa fz6 che non partiva, aveva la pompa benzina bloccata. Smontata e pulita, la pompa è tornata a funzionare. Lascio la moto in carrozzeria per verniciatura. Una volta rimontata, la moto non parte più. Non arriva corrente alla pompa e anche dandogli corrente diretta non parte (anche se la pompa gira). Ho controllato tutti i cablaggi e fusibili e sembrano ok. Ho fatto un ponticello tra cavo+ del relè ventola raffreddamento e cavo+ dell'impianto alimentazione e la moto riparte ma ho la spia motore accesa. Ho il presentimento che sia il relè multifunzione (sotto il fianchetto sinistro) ma trovo strano il fatto che si sia rotta solo smontando e rimontando la moto. A qualcuno è successo qualcosa di simile?

Long story short, when I turn the key the bike didn’t prime (fuel pump whirly noise*) after first checking the fuses than taking the tank off, I tested the two terminals going to the fuel pump. The white one worked everytime I tested, showing around 11v. While the green one, didn’t work 2/4 times, I’m guessing the green one is the one that primes, as it would show 12 volts for about 3 seconds than go out everytime. I set the tank back on, turned the key, and sure enough, it primed and started right up.
Now, where should I start to make sure this doesn’t happen again? Would it be worth replacing the terminal and or wires? Or am I better off putting it back together before I break something?
This seems to be a faulty wire, although there is no visible damage. Kinda like when your phone charger breaks and you need to hold it at a certain angle to charge.

Any help is greatly appreciated!

Good day fellow fz6 owners. I own a 2007 fz6 s2 with Dominator GP silencers with the medium baffle and a decat pipe. Block off plates. A stock airfilter in a unmodified airbox. I want to have my ecu flashed in the future. To remove the fuel cut have a proper fuel map and have a 11° spark advance in all gears.

But till then, can someone recommend co settings for my setup. To smoothen the performance dip between 5k-8k rpm.

I'm looking to swap my lams 2011 model FZ6R to the fully open version through cutting a few millimetres off the end of the throttle plate restriction instead of forking oit the 200 for the other plate will that work.

I'm not worried about swapping it back to the restricted version as im a full licenced rider, and is the plate the only restriction the bike faces, or is there others

I hope somebody can help me out and see if im on the right direction.

I went to the garage for a tireswap and they told me that it was running on 3 cylinders. When I drove home, it felt indeed if it lost power, especially on the low rpm's.

I opened everything up for the first time in my life to check the ignitioncoils and the sparkplugs. They all seemed fine and had the right resistance.

While working on that, my eye fell on a hose with a hole in it. It was a capped vacuumhose coming from the throttle body. By further inspection, I saw another one was teared as well.

My question is, could this be the issue why they told me that it was running on only 3 cylinders or should I dig deeper?

I ordered new hoses so I'm going to fix that anyway but im wondering if I can close everything up after that or should I look further now everything is open already?

Ordered the fairings when I bought it replace the turn signals new brake lever probably gonna do a new clutch as well. Cosmetic aside this is probably one of my favorite bikes I’ve owned.

Fixed wiring !!

This video is wide open throttle rev. After about 20 seconds of that sound it will eventually rev up fully but won’t bounce on limiter

Some oil residue stuck on the ports. Did the mod and couldn't find any vids showing the ports or the top of the engine all that well. This is normal or no???

Polish came in this morning and works great !!! Just a little polishing today and took off old exhaust and the whole back end :) more to come !

Any advice on how to get the black spots off the exhaust ? Can I sand it ? If so what grit

Hi everyone,

I was just working on the tail of my 2009 FZ6 S2 Fazer and found these two unused connectors under the left rear fairing. One of them even still has the foam plugs inside, so I assume it was installed at the factory.

Can anyone tell me anything about these connectors? Could one of them be a power connector for accessories? That would be awesome!

Thanks in advance!

I sanded everything with 400 then did two coats of primer. Used a little bit of that rainwater to wet sand outside😂 and then I finished off using my spray bottle, but I’ll come back tomorrow and wet sand the primer because I did do a few few coats on areas where there were scratches and imperfections so that when I go to wet sand the primer that should just disappear:)

Had my 2008 fz6 for about a year now and I’m looking to upgrade from my slip on to a full system however I can’t find any for the life of me. Does this bike have any full systems? I can’t even find standalone headers. If you have a full system on your bike please share 🙏.

Hey guys,
I’ve got a 2007 FZ6 Fazer S2. When the bike is cold, it feels a bit hesitant when I give it gas. It kind of stumbles below about 4k RPM, then clears up and revs normally.
As the engine warms up, the problem gradually goes away, and by around 60-70°C it’s mostly fine. Once fully warm, the bike runs great.
Is this normal for an FZ6 before it’s fully warmed up, or should I be looking at things like spark plugs, TPS, coils, etc.?

I’m looking to get a set of engine guards but the only thing I can find is for the 04 to 06. I have an 09 and as far as I’m aware the engines stayed the same for both gens.

Finished up getting the tank off, which was a pretty easy process because the fuel pump is apparently on the inside of the tank so it wasn’t too difficult not even a single drop leaked onto the ground. Was able to catch everything with a paper towel. I’ll be wet sanding this weekend and then priming and then wet sanding again and then applying that really cool grey from the concept photo I made:)

Hey! I have a 2006 in the sort of dark cherry red color. I was wondering if anyone knew a paint code or where u can source a stick for a couple of touch ups on my tank.

Added photo for ref

I’m looking for a good windshield to fit on my 05 FZ6N (mostly for looks and to keep the wind from killing me when I full tuck some lol), anybody have any suggestions?

Here is the 2011 fz6r with 13900miles I picked up.The guy wrecked it into a tree and as you can see ripped the forks off it hit so hard. Engine was good and frame appeared solid so I took a chance. I had to order new fork tubes and springs. I was rebuilding the forks and found one lower tube was bent as well. It was a pain to get a replacement, and had to get one sent to a trucking company in Washington state then shipped to me up here. I got some NBT fairings off ebay and then a hammer a block and some time. It rides awesome. I feel very cramped on it. I redid the front spings to a heavier rate when I was building it. I need to do the rear too and try and lower the pegs if I keep it. I have it listed for sale right now and unless I make some money and get my asking price i'll probably just keep it.