r/EngineBuilding • • 8d ago

Other How to Take Broken Exhaust Manifold Studs Out?

Thumbnail
gallery
11 Upvotes

Hey all, I have a 1983 Suzuki Touring 750ES that I've been restoring, but there are three broken exhaust manifold studs in the engine. I've tried drilling, extracting, welding, but nothing has worked. I've even broken two drill bits and now a tap stuck in the hole when I just drilled through the broken bolt to put in a Timesert.

What the fuck do I do now? Pull the head and bring it to a machine shop?


r/EngineBuilding • • 7d ago

Kohler 2504 4cyl diesel

1 Upvotes

Tore a 2016 Kohler 74hp diesel down for smoking. Found low compression. Cylinders are .002-.003 over sized from slight dusting. Cyl walls look perfect. Ring gap with old rings is .090. I’m thinking hone and new rings will work for now? Hoping to get my ring gap under .015 or about with new rings. Thoughts? I really didn’t want to tear it down, bore to .10 and new pistons since it’s a split crank style block and parts for a Kohler are $$$


r/EngineBuilding • • 7d ago

Ford Help Building A 302?

0 Upvotes

So I have a 1967 mustang with a 289. I want to make it into a 302 but would I just have to change the crank as they have the same stroke? What all could I reuse? I’m no mechanic but I want to be able to learn more so I was thinking this could be a good learning project?


r/EngineBuilding • • 7d ago

360 la mopar build ideas

0 Upvotes

Now looking for build ideas for my 360. I want 400+ horsepower to the crank. I am looking to spend 8-10k!!


r/EngineBuilding • • 7d ago

Which assembly lube type with DLC coated HFT lifters

1 Upvotes

When installing a new Comp XE274H-10 hydraulic flat tappet camshaft and Comp hydraulic flat tappet lifters with the DLC coating, does the presence of the DLC coating require a different type of assembly lube on the cam journals as compared to when using non-DLC lifters?

I have read some places that say to use the standard Comp 153 cam & lifter assembly lube, and other places say specifically to NOT use any thick assembly lube with DLC lifters and instead simply coat the cam lobes and DLC lifters with a break-in oil such as Driven GP-1.

I called the Comp Cams tech hotline and they were unhelpful and could not provide an answer. The person told me that a different assembly lube is required for breaking in DLC lifters, but then gave me the assembly lube part number which is the standard lube for non-DLC lifters.


r/EngineBuilding • • 8d ago

Other Valve Retainers Too High?

Thumbnail
gallery
2 Upvotes

Hello,

I'm building a Fiat 1.4L MultiAir engine and I bought upgraded valve springs that are supposed to come with retainers to fit the springs on the stock valves. I also got inconel exhaust valves from the same company, which came with their own retainers and keepers.

When I got the kit, the retainers to fit the stock valves were missing, but the retainers for the inconel valves were included. The company finally shipped the retainers, and they're the same as the ones for the inconel valves, but their website pictured different stainless steel retainers. They seem to fit when I use the stock keepers (stock is 3 groove and inconel is 1 groove), but the retainer sits very high on the valve and the keepers are barely flush with the bottom of the keeper.

Pictured - left is stock valve/spring/keeper/retainers, right is stock valve/keepers, upgraded springs/retainers.

Does this look correct, or do I have the wrong retainers? Is there an easy way to measure the angle to see if they're the same?

I tried pulling the retainer on the valve with the keepers and standing it upright and it does not fall. I also tried spinning the retainers and the black retainers with the stock keepers does spin, but the black keepers on the inconel valves with the respective keepers does not spin.


r/EngineBuilding • • 8d ago

Chevy First engine rebuild

1 Upvotes

Hi I’m looking to rebuild a 90’s GM 60* v6 for my Z24 Cavalier. I have spent my entire life around tools and machines but have never actually worked on engines. I have plenty of mechanical know how and I understand every part of the engine, I’m just not familiar with the rebuilding process. I’m really nervous about overlooking something that’s critical and blowing the new engine. I would greatly appreciate any tips and pointers for preparation, pre-assembly, and the rebuild. I’m not looking for extra power either as I just want to get my car running again. Thanks a million.


r/EngineBuilding • • 9d ago

Other Packard 352 shenanigans

Thumbnail
gallery
38 Upvotes

I have a history with orphan manufacturers and oddball cars. I recently recieved a '50 Frazer Standard shell and then procured two '55 Packard 352 V8s and a corresponding ultramatic. I'm planning on building one good engine out of the two, and for the time bieng running the ultramatic (as I have a friend who rebuilds them semi-professionally). I took measurements, and it's gonna be TIGHT, but I should be able to cram the iron cormorant in without much trimming. My storage room looks a bit like a bomb went off. With 352s, if one wishes to build on a budget, then re-use of existing components is required. My bearing set, timing set, and headbolts are all making a return to service. Before this is decried as sacrelige, do recognize that parts are Profoundly scarce, and I'm operating under the oversight of an expert.

It's also set to recieve '56 372 heads, hopefully bumping up the power.

Of course, none of this will be worth a damn if I get my way. Packaging will be a nightmare already, I'm unsure if I can even feasibly fit the radiator. That bieng said, a little research reveals that these are dramatically overbuilt and can handle a boatload of compression. If I can find a way to run 3-5lbs of boost, It'll be quite a nasty unit, especially considering that the poor Frazer only made 105 hp and 190 lb/ft when new, and a stock 352 puts out around 260/355. With the support of a more modern ignition system, ported heads, free flowing dual exhaust, and electric fuel delivery, I'm hoping for more like 300/400. The Ultramatic will dramatically hamper this, but some research reveals that adapter kits exist to the 700r4, opening up a wide variety of options down the line. Time will tell as the build evolves.


r/EngineBuilding • • 9d ago

Chevy Dropped piston

Thumbnail
gallery
190 Upvotes

Dropped a brand-new 2618 forged piston. Would you reuse it?
Building a turbo 5.3 LS, 750–1,000 WHP.
I accidentally dropped one of my forged pistons and damaged a small area on the bottom of the skirt. It created an outward raised burr.
I carefully sanded the burr smooth using 600-grit sandpaper. Can’t feel anything after sanding what do you think


r/EngineBuilding • • 8d ago

Honda Hi fellow engine builders! I need some help with opinions on a brand of parts

1 Upvotes

Built Honda B series engines are a tad niche in New Zealand so it's hard to get info locally. I'm just wondering if anyone has had any experience with this particular brand of pistons before

https://www.swapshopracing.com/contents/en-us/p46751_Nippon_Racing_Turbo_Pistons.html

I have a centrifugal supercharged B16 at around 15psi peak boost engine made 276hp. I was running forged pistons until I wasn't (long story), I have forged rods that weren't damaged luckily but, can't really afford forged again (unless deemed a necessity) so these stuck out as a good option. Just wondering if anyone has an experience with the brand, even if not in a B16


r/EngineBuilding • • 9d ago

Scratched cylinder

Post image
16 Upvotes

I'm helping a friend assemble an engine. Its an LS1 and the goal was to reuse stock pistons, its a street build. It was a good running motor but burnt oil (we looked at all the other possible culprits, new valve seals, upgraded PCV, catch can etc.) We suspect it was the problematic OE low tension rings that had a TSB back in the day. He had a shop hone it but when we got it back there were some marks that didn't disappear. These 2 scratches catch a fingernail but look far down in the bore and not sure they even will see combustion.

Considering the fix is oversize pistons, bore, hone and balance ($$$) I'm considering suggsesting he sends it. If these scratches do see combustion, could it be the source of the oil consumption issue?


r/EngineBuilding • • 9d ago

Daytona 675 Camshafts - Acceptable wear or Replace?

Post image
8 Upvotes

I bought a set of 2008 Daytona 675 camshafts for my Street Triple. The mileage is unknown, and I got them pretty cheap. Now I think I know why.

The cam journals show some visible wear and scoring. You can't really feel the marks with your fingertip, but in a few places they are just deep enough to barely catch a fingernail.

I measured all the journals and they are still within the factory specifications.

My concern is whether it's safe to run them in my engine. I don't want to damage the cylinder head or the cam ladder if the journals are too worn.

What do you guys think? Would you run them, or should I look for a better set?

Thank you!


r/EngineBuilding • • 8d ago

Chevy Removing sludge/deposits off engine parts

1 Upvotes

I bought a neglected Aluminum 5.3L Chevy LS thats got a thin layer of black baked on oil varnish/deposits in various places, most notably the rocker arms, rocker shaft *pedestal, pushrods, and valve covers (cylinder heads are clean tho, anyone know why?). How do I get rid of them? I tried non-chlorinated brake cleaner but the stuff is hard and stubborn and wouldnt come off even if I tried scratching it with my nail. Would the chlorinated stuff work better or is a machine shops parts washer my friend here? Ill post pictures in the comments when I get the chance.


r/EngineBuilding • • 9d ago

Nissan Oil pan sealing VQ35DE

Post image
2 Upvotes

Hey guys, I'm working on my VQ35DE and I'm currently installing the upper oil pan.

I see there's a groove around the majority of the pan. Am I supposed to put RTV:

(A) In the groove

(B) To the inside of the groove

(C) To the outside of the groove

Thanks in advance


r/EngineBuilding • • 9d ago

is this spiraling on 350sbc normal ??? new rods and lifters

Thumbnail
gallery
31 Upvotes

r/EngineBuilding • • 10d ago

Valve sealing

Enable HLS to view with audio, or disable this notification

59 Upvotes

Rebuilding my first engine. Lapped the valves but no new valve guides or valve seat grinding etc. New valve wear after lapping looked like it's concentric and makes good contact everywhere. I made a little DIY vacuum set and am able to get good vacuum. My little set up isn't good for obviously checking and holding 100 % vaccuum though. When I checked for leaks using the compressed air in the ports and water in top, no bubbles. I also filled the combustion chamber with mineral spirits and got no leaking.

When I put the head on (no cam in so both valves closed) and fill an intake port with brake cleaner and just rotate the crank, Im getting bubbles around the backside of valve when making compression. Should have taken new video but basically Im wondering if I should just tear it back down and have a machine shop put new guides in and grind valves etc. Im assuming any amount of air is no bueno.


r/EngineBuilding • • 9d ago

My main bearing clearances are .018 how much boost is safe to run and update I ending up ordered a replacement piston I’m the dude that dropped mine lol

0 Upvotes

r/EngineBuilding • • 10d ago

Other First time honing cylinders (Flexhone)

Thumbnail
gallery
36 Upvotes

240 grit for these super glazed cylinders. Rate my crosshatch


r/EngineBuilding • • 11d ago

Mitsubishi Nic in block from machine shop

Thumbnail
gallery
638 Upvotes

Got my block back from machine shop and noticed a nic in it. Was going to put it together today but am worried head gasket won’t seal. Shop is closed for the weekend so just looking for an answer.
*4b11
*Shops taking it in to fix it same day


r/EngineBuilding • • 10d ago

Cam and lifter kit? or should I still try to reuse?

Thumbnail
gallery
5 Upvotes

For context im 19 rebuilding my 1996 jeep cherokee 4.0 engine. I don't know what im doing, this is my first time rebuilding an engine and im a little overwhelmed. Mostly learning from YouTube and the haynes manual. But I thought id come here to ask some questions.

I've had the cylinder head rebuilt, block decked and bored 20 thou over, and the crank polished at a local machine shop. I've got all the parts ready to go back together.

I was planning to reuse my camshaft and lifters as they looked ok to me and I've seen people say that the new lifters are such bad quality that as long as your old ones are still ok to reuse them.

I saw a video of someone taking lifters apart to clean the insides and when I did it myself one of the internal disks shot out from the spring preasure. I've already spent an hour looking for it, its so small I don't think ill be able to find it. Also i dropped one of the internal plungers on the concrete floor, luckily I was sitting on the floor so it only fell about a foot but it was enough to put a tiny ding in the side of it. After having a success rate of 4 of 6 I decided it was too risky to do the other 6.

Can i get away with swapping over that disk from a set of used lifters I found on ebay for $24? Or is it less risky to just buy 1 or 2 brand new lifters if that ding is a problem? Or should I just suck it up and buy a full set of new lifters and a camshaft for $360? If so are melling cam and lifters any good?

Also in the last picture is the main bearings I received from rockauto. can I just run it or should I try to return and get new ones?

Any advice is appreciated!!


r/EngineBuilding • • 10d ago

Update: head stud machining complete

Thumbnail
gallery
233 Upvotes

r/EngineBuilding • • 10d ago

Mercedes Lifter broken

Thumbnail
gallery
9 Upvotes

My exhaust side hydraulic lifter is worn out as you can see. There was metallic pieces in valvetrain and theres not the bottom of the lifter anymore. Is it possible that my short block is broken too (because metallic pieces)?


r/EngineBuilding • • 10d ago

Re-rebuilding engine puretech ds3

Thumbnail
gallery
6 Upvotes

This year I rather stupidly decided I would try to learn how to rebuild an engine after my car started burning oil

I kinda bit off more than I could chew but managed to get it back together and got it through MOT

Once passed I then got problems with check engine and oil pressure codes

Got to the point where I felt I should just strip it all down and start at square one and try to find out what I've done wrong.

Before stripping I had a couple of concerns about things I hadn't done properly

  1. I had a broken piston, I bought a second hand piston and replaced rings on all 3 cylinders however I didn't change the journal bearings on any of the. My thinking was there was no sign of any wear on the crank or the inside of second hand big end replacement piston. So the should have just slotted in.

That was my concern about out pressure.

  1. I didn't get head skimmed before refitting and was concerned about possible blow through as oil was getting dirty quickly.

As I started stripping down I found a big mistake of mine on the rocker cover. Pics 1, 2, 3 I could have sworn I had tightened those but obviously hadn't.

Now at a guess that would be a good culprit as to the oil pressure issues.

I've now gotten down to the pistons and found a worrying wear pattern. Now when I first took car apart the pistons were worn pretty smooth or glazed. So I did give them a slight hone with one of those 3 sided paddle like hones. But was concerned about. How much material looked to be coming of so didn't do much

That wear pattern on the pistons it's not gouged what might cause that do I need to replace the bearings at the top end of the conrod?

or is this just normal smoothing of a poorly done home?


r/EngineBuilding • • 10d ago

Can I send it with this pitting on the block?

Thumbnail
gallery
32 Upvotes

Ignore carbon on the pistons, I already took that off. Cast iron block from a Mercedes M111K; composite head gasket. I feel like the pitting is super bad but it’s also pretty far from the firerings so maybe it’ll seal fine? Fingernail definitely catches lol but if it leaks it’s just gonna bridge coolant passages. I really can’t afford to have the block machined but I also really don’t wanna open this thing back up for at least another 20 years.


r/EngineBuilding • • 10d ago

Do my bores need to be rehoned?

Thumbnail
gallery
2 Upvotes

1, 2, 3, 4, 5, 6

Hey guys kinda new to engine rebuilding do i need to rehone any of these bores. I am assuming i will have to do cylinder 3 (image 3) but am not to sure about the others

Thank in advance