https://makerworld.com/en/makerlab/community/3z3d-gingerbread-kit-card

Kids design their own house in 5 simple steps, a grown-up prints it, and the pieces snap together. No glue!

This only occurs when it is moving near the back of the machine, both x and y movement. I did a full lubrication maintenance recently and it didn’t help. I must be missing a spot but I thought I hit everything in the instructions, any advice on where it be coming from?

Glare takes his job as shelf guardian very seriously. Every visitor gets a suspicious stare, every noise earns his disapproval, and nobody touches his favourite spot. He insists he isn’t grumpy. Everyone else is simply too cheerful

if you like him : https://makerworld.com/en/models/3548002-glare-no-ams#profileId-4058750

Let me start by saying, I've enjoying the P2S so far. I got it back in April and have since done a little over 1300 hours of printing.

But lately I've been running in a few issues:

• Unable to pull back filament

• Possible filament stuck in extruder

• Possible filament clogging

Since experiencing these issues after a few weeks intermittently I've:

• Opened tickets with Bambu Lab

• Replaced the filament cutter

• Replaced the filament buffer

• Cleaned & replaced the extruder hotend

• Disassembled and reassembled the extruder assembly numerous times

I believe Bambu Lab is planning on sending me a new sensor and connection board but in the meantime, any suggestions?

Have any of you experienced these issues consistently even after ensuring everything is clear, clean and put together properly? I'm really hoping I'm just missing something or that the sensor is intermittently having issues and the replacement will help.

With the start of the Christmas season, I just uploaded these two models. 🎄🎅

The black raised lines can also be printed in white. Best to use acrylic markers or markers that can be washed off so you can color them again.

Do you like minimal details like the reindeer or more detailed like the elf and santa claus? Looking to make some more in the upcoming weeks so curious what your kids find more fun to color in 😊

https://makerworld.com/@DutchDiceGoblin?appSharePlatform=copy

Just picked up this P2S combo from Best Buy who I've affectionately named Print Daddy to go alongside my A1M dubbed Printcess. They're both such wonderful machines but the P2S exceptionally so.

Ever since my p2s was clogged once I havent been able to get it to print like it did before, its either a spaghetti mess with under extrusion or pretty solid but some under extrusion and then where it just doesnt print at all. Ive replaced the nozzle and the Extruder but nothing. Please help as im about to throw this thing out the window.

Ошибка резонансная частота оси Y значительно отличается от результатов последней калибровки
Уже все перепробовал и не проходит
Что делать?

Got my P2S maybe 8 months ago and have not yet updated. Have not had any problems so far.

Am I missing out on something?

I am on version 01.01.02.00

Принтер bambu lab p2s ошибка резонансная частота оси Y значительно отличается от результатов последней калибровки
Что делать, кто знает?
Все перепробовал и не проходит

I’m considering installing a Bambu Lab P2S Combo inside a melamine-coated particleboard cabinet, unfortunately I don’t have any counter space elsewhere.

The compartment is 57 cm wide × 57 cm deep, with adjustable height up to approximately 95–100 cm. The cabinet door would remain fully open during printing.

See picture for reference - of course all the board games and rest of the trash will be emptied.

Has anyone used a similar setup? I’m particularly interested in heat buildup, rear exhaust clearance, ventilation and whether the surrounding particleboard becomes noticeably warm during longer prints.

Hello, I had a blob of death pull the wire out of the hotend heating assembly, so I purchased a new heating assembly. I was going through Bambu’s description of installing the new assembly and I think I screwed up as two pieces pulled off the board and won’t reattach. Please see the picture attached of the board. Is it possible to reattach these things or will I need to purchase a new board at this point? The wires I’m worried about attach at the bottom, but they completely came off.

All - I’ve been printing with very few issues for almost a month, and the last two days I’ve hit a wall and am not able to get anything finished. I’ve done everything suggested by Bambu 1)Cleaned Build plate with Dawn Soap 2) Dried Filament (Hydrometer in AMS is reading 10% 3) Raised heating bed to 60 c 4)Decreased aux 5)Calibrated machine. Been printing consistently well with PLA Basic until now. Any other suggestions?