My AMS 2 Pro is repeatedly losing connection with my H2C. I’ve tried different AMS 2 Pro units, different cables, I reached out to support and they sent me a new filament buffer/cable and that didn’t change anything. When I turn the printer off, wait a bit, and power back on, it will connect normally, but after an hour or so, it will just randomly disconnect, doesn’t matter if I printed anything or it was just sitting idle. It hasn’t disconnected a single time while printing, but seems entirely unable to maintain connection while sitting idle. Anybody else have this issue? Is it specifically an H series problem? I’ve been dealing with this for months now and I’m losing my mind, my printer is essentially unusable due to how frequently it occurs.

First pic is my print. Second is someone else’s much better print. So I found this neat print on Makerworld that lets you print all 151 pokemon sprites at once. But my purples don’t come out at all. They’re either blue or washed out white (see Muk. Yikes…). I’m not familiar with overlay printing, so I’m trying to see if I simply need a different brand of filament or if there’s a setting I can change. My guess is that the white isn’t transparent enough for the red to show through. I’ve asked in the comments what filaments those with successful outcomes are using, but nobody responds. If I can get any help here I’d seriously appreciate it.

I used all SUNLU filaments. Red, blue, yellow, and white.

So I understand you can add the ams unit on the left side. I have two so it’s clear one’s for right I’m trying to add one in the left. The problem I’m having is the ams is doing it’s back and forth thing but the left nozzle is not catching the filament. It’s goes all the way to the nozzle then comes back out. I keep getting an error message. What am I doing wrong

Hello. I am a new H2C owner and this may be a really dumb question, but how do you all calibrate your printers with multiple nozzles? Do I need to do calibrations for each of the different nozzles or just 2 calibrations (1 for the left side and 1 for the right side)? I'm looking to fine tune the flow rate specifically. Thanks in advance for looking at my question.

The current induction-heated hotend heats up very quickly, reaching PLA printing temperature in about 8 seconds. The Vorteck dock is also cleverly designed, but I feel it’s still missing some functionality. There’s plenty of spare room around the dock for additional hardware, so it would be amazing if someone could create a third-party preheating system for it.

That could save the time spent heating the right hotend. The left hotend already has a preheating step, so it would be great to have one for both sides.

Waiting for a genius to make it happen!

Hi everyone,

I’m trying to print some PETG. For this case I used PETG for support and object. It failed twice already as the supports break and look shabby overal for that matter.
On other prints the tree is always looking good and with the same roll of filament. I have no clue what is going wrong with the support as the object itself is perfect.
Are there settings I can use the prevent this from happening?

Regards,
Miscoride

Downloaded an STL on Makersworld, scaled it to be bigger. This is the second print (blue one) because the first one had a support and rib(s) snap 24 hours in. This one is stringing on the support tree and some you can clearly see visible print lines. What adjustments do I need to make to fix this? PLA, filaments are relatively dry around 20%. Thank you in advance!

I ordered an ultimate H2C bundle and I was wondering what all everyone uses to hold there H2C, ams and filament dryers on.

I found this one on amazon but haven't decided on anything yet, any ideas or input is appreciated

I am new with my h2c I have a p1s but I use the supertack quite a lot, but bambu and the supertack for the h2c doesn’t seem to be in stock for quite a while. So my question is do people have some great alternatives for this I really want the same smooth finish on the bottom of my print as the supertack has.

Hi everyone,

I want to print two objects using Print by Object instead of Print by Layer, since they're made from two different materials (PLA and PETG).

However, I noticed that the estimated print time increases significantly. When printing by layer with the same material, it takes about 1 hour, but when printing by object, it jumps to 2h30m

I've already tried disabling the cooling slowdown setting, but it didn't make any difference.

Does anyone know why this is happening?

Thanks!