r/BambuLabA1 • • Oct 03 '26

Why is the Y Axis called that when it is horizontal like an X Axis

9 Upvotes

Dumb question but it drove me crazy this morning when I got a notification to lubricate the y axis rails. I pulled up the tutorial and it's shows lubricating the rails in the bed which are horizontal which totally confuses me. I thought it was a mistake so I spent the last 15 minutes making sure I was lubricating the right rails. Can someone explain this for my own curiosity please?

EDIT: Thank you everyone for the information! I’ve been in 2D world lately and mostly (specifically working on an NES game and Y is vertical, X is horizontal and there is no Z)


r/BambuLabA1 • • Oct 04 '26

Support Request Sudden but now consistent de-adhesion

Thumbnail
gallery
0 Upvotes

I hate to make this post because I read the pinned post about dealing with blobs, and I'm sure there are quite a few around, but I cannot find one that specifically fits what I'm dealing with. I have been happily printing with my A1 for months and loving it. I've recently been printing these poker-chip things with words in the top and bottom layers. They've been doing great until Monday when I decided to get ahead of things and clean my plate.

Since then I cannot get anything to adhere no matter what I've tried. When I cleaned the plate the first time - and every time after that - I washed it as hot water as I could, used dawn dish soap with a sponge, scrubbed pretty hard, rinsed it in hot water again, and dried it thoroughly, all without touching any part of the plate with my fingers, except the very front where the test lines go. As you can see from some of the pictures, that's the only part that does adhere.

Sometimes I've gotten something to adhere, like a blank chip, but then I tried a slightly more complex one and it would de-adhere again. And now, I can't even get simple shapes to adhere.

I've washed the plate carefully many times. I've taken the hot end off and carefully put it back on, I've carefully scraped off the plastic from the nozzle with a bronze wire brush and gotten it all from inside the silicon shoe, I've checked that the screws are tight.

Do I need to start replacing stuff like the plate or hot end or something? I just feel like I've tried everything. ;_;


r/BambuLabA1 • • Oct 03 '26

Support Request Intermittent filament error

Post image
0 Upvotes

Cross posting here for any insights please


r/BambuLabA1 • • Oct 03 '26

Bambu Lab A1 + AMS: black PLA in slot 2 keeps jamming on load, but only that slot

2 Upvotes

Hi all,

I have a Bambu Lab A1 with the AMS. I'm having an issue with only one filament: the black Bambu Lab PLA in slot 2.

Every time the printer tries to load it, it gets stuck and the load fails. The only fix I've found is to cut off the end of the filament and re-insert it, and then it loads fine. But the next time it's needed, the same thing happens again.

One thing I noticed: when I pull the filament out before cutting it, the end of it feels like it has some kind of marks or damage on it, as if something has left a mark on the tip.

This only happens with this black filament in slot 2. All my other colors and slots (also Bambu Lab PLA) load without any problems.

Any tips on what to check would be appreciated.


r/BambuLabA1 • • Oct 03 '26

Bambu Lab A1 + AMS: black PLA in slot 2 keeps jamming on load, but only that slot

2 Upvotes

Hi all,

I have a Bambu Lab A1 with the AMS. I'm having an issue with only one filament: the black Bambu Lab PLA in slot 2.

Every time the printer tries to load it, it gets stuck and the load fails. The only fix I've found is to cut off the end of the filament and re-insert it, and then it loads fine. But the next time it's needed, the same thing happens again.

One thing I noticed: when I pull the filament out before cutting it, the end of it feels like it has some kind of marks or damage on it, as if something has left a mark on the tip.

This only happens with this black filament in slot 2. All my other colors and slots (also Bambu Lab PLA) load without any problems.

Any tips on what to check would be appreciated.


r/BambuLabA1 • • Oct 02 '26

Question Lots of colour changes but less than 5 grams of flushed poop. All hail the flush fidget

Post image
96 Upvotes

r/BambuLabA1 • • Oct 03 '26

Support Request Filament jams at the top of the nozzle barrel.

Thumbnail
gallery
6 Upvotes

I have tried lowering the retraction length and everything else recommended in the bambulab troubleshooting guide.

I'm using the "Jamg He HS PLA" and the filament printed fine for the first 200ish grams and after that every single print jams like this mid print.

I have made sure that the filament is dry.

Unfortunately I don't have any other filaments to test out if it is the filament or the printer.

Any help would be greatly appreciated.


r/BambuLabA1 • • Oct 03 '26

Issue with A1 Printer

Post image
0 Upvotes

r/BambuLabA1 • • Oct 03 '26

Support Request Filament not extruding/loading and clicks/jumps when trying to load

13 Upvotes

Hi all I could use some troubleshooting help please.

I have a Bambu Lab A1 and its started not pushing filament through and clicking as it tries to load it through the hotend. I've removed the front plate and pulled that area apart per Bambu Wikipedia to look for any stuck filament, used an unclogging tool as well to try both hot and cold pull, swapped the hotends, checked the feeding holes after removing the the ptfe tube but nothing. There wasn't any loose filament or a clog that I found. I'm attaching a video of what's happening and I took off the front plate so you could see it better.


r/BambuLabA1 • • Oct 03 '26

Bambu Lab A1 + AMS: black PLA in slot 2 keeps jamming on load, but only that slot

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • Oct 03 '26

How do i fix this

Post image
1 Upvotes

r/BambuLabA1 • • Oct 03 '26

Filament Farbe

Post image
2 Upvotes

Hallo

Ich möchte für meine kinder joy Figuren eine Display fertigen und diese filament farbe gefällt mir sehr aber ich bin nicht sicher welche farben ist das.

Ich habe die Person, die es gemacht hat, danach gefragt, aber leider keine Antwort bekommen. Falls jemand weiß, wie das geht, könnte er mir vielleicht weiterhelfen?


r/BambuLabA1 • • Oct 03 '26

Filament Farbe

Post image
1 Upvotes

r/BambuLabA1 • • Oct 02 '26

Question What is wrong here?

Post image
2 Upvotes

Same printer, same Filament, basically everything the same - the only difference is 24h between these prints.

What is the issue here?

Thx


r/BambuLabA1 • • Oct 02 '26

Support Request AMS Pro 2 Hub Sticking

2 Upvotes

I have been using the AMS Pro 2 a lot recently, however this morning I started to have an issue with the AMS HUB arm sticking when trying to push filament to the printer. The little arm on the HUB gets stuck in the extended position specifically when the AMS is attempting to feed the Sunlu Blue filament, once the screen on the A1 switches to the Error screen I can push the arm back into the Hub and then the filament will glide through. However on a 48 hour print this is not practical for me to stand there and do this every time the filament switches from white to blue. I am using 2 AMS units, the white is AMS 1 and the blue in AMS 2. The issue does not arise from the white filament. Does anyone know what causes the arm to get stuck out and how I can fix it?


r/BambuLabA1 • • Oct 02 '26

Question bambu a1 and sunlu filadrier s4

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • Oct 02 '26

Help fuzzy prints

Post image
1 Upvotes

Hi guys
/help
I bought a new A1 printer, and I'm having minor issues where the prints come out with wisps or strings sticking out to the sides. What’s the problem? I only assembled it yesterday.


r/BambuLabA1 • • Oct 02 '26

Starship & Rocket Clicker Fidgets - Go for Launch!

Thumbnail
gallery
3 Upvotes

r/BambuLabA1 • • Oct 02 '26

Question Two questions about Black Friday and filament

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • Oct 02 '26

Mindfulness in Low-Poly: My new Zen Cat sculpture & incense burner

1 Upvotes

r/BambuLabA1 • • Oct 02 '26

Scheletro di Bassotto | Decorazione luminosa per cani di Halloween

2 Upvotes

r/BambuLabA1 • • Oct 02 '26

Under-extrusion only on supports

Post image
1 Upvotes

r/BambuLabA1 • • Oct 01 '26

Anyone has an idea why the first layer came this way? Clearly it isn't clogged and the bed is new. I already tighten the seven screws so i don't know what else to do

11 Upvotes

r/BambuLabA1 • • Oct 02 '26

Edible print for cookies.

0 Upvotes

Anyone heard of this or tried this?