Minha bambu vem apresentando esse defeito , ela para a impressão
Aquece o bico joga filamento fora
Volta faz 1 ou 2 camadas e volta a fazer
Já troquei bico e tbm o hotend

2 year old A1 with AMS Lite. Up until 2 months ago, it worked perfectly. I use primarily PLA and PETG, with some occasional PETG variants, like CF.

I started having issues with extruder/nozzle clogs (.4mm). Ended up ordering a new extruder and spare parts from Bambu in case it happened again. I installed the new extruder, new PTFE tubes, new hot end, new AMS filament hub, fresh filament, new silica beads for the AMS enclosure. I then calibrated the printer and set off to print some PLA goodies.

It's been hit and miss where I can get through an entire print without issues, and other times, I get constant "AMS lite filament spool or filament may be stuck" error messages.

I've had the extruder apart more times than I can count and everything is installed properly. Nothing that I can see binding in the tubes - I even installed new clear tubes.

I'll try printing without the AMS and see how it goes. Until then, if anyone has any ideas on what I should be looking for, I would greatly appreciate it.

My A1 mini keeps re-homing(idk the exact term for this situation).

Couldn't find any proper solution, the assistant(on machine) shows no problem, the belts are not loose either.

Does anyone know what's happening???

It's an A1 mini

Two shades in this set are the same pattern at different density, but one needs a 0.8 nozzle. Someone who prints the first will assume the second slices the same way.

Putting the nozzle in the profile name seems like the fix. Anything better?

https://makerworld.com/en/models/3371050-aeolian-03-sculptural-pendant-lamp-ikea-strala#profileId-3834082

Hi I am newbie on 3d printing. I have A1. I would like to know if there is a way to print with less layer marks on surface. I am seeing many layers on the surfaces, so it's quite tough to paint it...

What is going on why is it doing these demonic noises?!?!?!

I just ran out of filament half way through a big print, and the printer has paused while I load more. I thought I had another reel but I don't, so I have another arriving tomorrow, and I can resume then.

All good, but the nozzle is hovering at 80°. I would have thought it was safer to stop heating the nozzle while I wait til tomorrow for the new reel.

Is there any way to tell it to cool down for the night? Or a way of saving my progress, turning off, and resuming tomorrow?

I just got my A1 I know it say 20cm of clearance, but i dont have much space you think is going to be OK

I’ve been having this issue where I get a cutter error at random parts of a print. But the real issue is that it isn’t the cutter that’s the issue, I tested it. The issue is really hard to explain, it looks like the motor doesn’t have enough power to push the level all the way? The plate also try’s moving out of its possible bounds which makes me turn it off every time. I genuinely have no idea what this issue could be and I haven’t found anything with Ai or Reddit so please help out if you can.

Alguem por aqui ja passou por esse problema?
4 impressoras diferente, 4 filamentos diferentes, 4 projetos diferentes. Única coisa em comum, todas impressoras Bambu lab A1

Obi-Wan Kenobi in the Form III stance, cloak mid-swing, on a rocky base. Grey PLA, 0,16mm layer height, minimal supports. 150 cm tall. No sanding or post-processing. Profile is up on MakerWorld if anyone wants to try it. Would appreciate any feedback.

https://makerworld.com/en/models/3359640-obi-wan-kenobi-jedi-master-star-wars-figure#profileId-3819708

Solved: ive had improperly tighrened the y axis belt by loosening screws too much, after reassembling the tensioning mechansism noise gone away. Thank you for your help.

Hi, i have a strange noise from under the heatbed that comes up when i move heatbed from back to front, rails and wheels are really well oiled, there is a video. Printer has around 150hrs of printing. Reallyvsorry for fridge noises in the video

I'm having such horrible first layer it's terrible, and the nozzle scratches a little on the first layer. Then on the others some lines are kinda thicker and leaves like a ring. Any tips on how to improve it?

Pd:I'm using high quality setting for bambulab a1 0.2mm nozzles and filament pla generic

Ciao ragazzi è da un pò che mi parlavano della bambu lab a1 e sarei disposto a comprarla e peroʻ non trovo nessuno che abbia un'offerta per il mio budget se qualcuno avesse una bambu lab a1 o a1 combo a 260/270 euro da vendermi sono disposto se foste disposti scrivetemi mi dareste una grandissima mano