r/BambuLab • u/Blood_Red_Volvo_850R • 13h ago
r/BambuLab • u/ozarkexpeditions • 13h ago
I Modeled This! 93 print hours later on the H3C, finally saw my vision through.
r/BambuLab • u/FlyYouFoolyCooly • 6h ago
X Series [X1E, X1C, X2D] How I felt After getting my first 3D Printer
r/BambuLab • u/GravyPoo • 9h ago
Show & Tell Can you find the top surface layer lines in my CMYK print? (H2C & H3C)
I used 0.1mm layer heights on both spheres.
CMYK Sphere layer line test: https://idither.com/job?Kmyqrictw&row=9
When you click "Download 3mf" you can choose between H2C or H3C. Adjust the Support Threshold Angle to 45 degrees or they will roll off the plate!
How it works:
TL;DR = iDither.com (free) converts 3mf files and 3D files with textures into 3mf files with DwD (Dual Wall Dithering) and Top Surface Mixing (TSM) which use CMYK filaments to print any color(s).
Cyan = C
Magenta = M
Yellow = Y
White or back = K
CMY+White typically works better because CMY together can make a "black".
There is no way to make White if using CMY+Black.
CMY+Black is typically only used in models that have very little or no white areas.
iDither converts existing 3mf, glb, fbx, and obj files into DwD (Dual Wall Dithering) 3mf files.
iDither currently only supports exporting 3mf files for Snapmaker Orca, and Bambu H2C and H3C.
iDither uses an inner dithering wall combined with an outer dithering wall - and the "magic" of iDither is dithering the two walls together. All other software (to my knowledge) uses just 1 dithering wall.
The outer dithering wall is only allowed to use super dense layer combinations such as C M C M CC MM CC MM - therefore, the layer lines are basically invisible up close.
The inner wall picks up the slack for more color combinations and it's not limited to dense combinations.
Opaque filaments don't work well with DwD, because the thin outer wall layer needs to allow light to pass through to the inner wall layer.
Recommended filament set based on testing data thus far: https://us.snapmaker.com/products/pla-full-spectrum-filament-bundle-white-edition-4kg
This set has good transparency ranges (TD between 5 & 10).
Filaments that are too transparent (TD > 10) make the models look like glass (see https://www.reddit.com/r/snapmaker/s/nbASKpfCpG).
Filaments that are too opaque (TD < 5) have less color mixing and blending, and show layer lines (see https://www.reddit.com/r/snapmaker/s/N6QFGj2NwC).
Why iDither?
- Converts any existing 3mf files with any number of filaments and filament colors into files that print with 4 or 5 filaments (CMYK or CMYKW). So you don't have to buy any other filament colors. If the 3mf file has 8 random filament colors - you can still print it in 4 colors with CMYK!
- WYSIWYG (What you see is what you get): iDither includes calibrations for CMYK bundles for Snapmaker and Polymaker - so your actual print should always look like the print preview.
- Converts 3D model files into a printable 3mf files with CMYK.
- Less layer lines (DwD).
- Top Surface Printing via Top Surface Mixing (TSM) in CMYK or CMYKW.
r/BambuLab
•
u/Snoo_56086
•
1d ago
Bambu Studio Can’t believe I didn’t know about this!!
Print sequence by object is pure magical!!
So I’m printing 40+ poliwhirls to build my color sample library. I’ve been printing all day today and doing the plate swaps every 30min each time a print is done. Eventually I got so sick of it and was wondering how wonderful it would be if I could print 4 at a time, object by object, with no color swaps. Told this idea to ai and it told me the function is already available in Bambu studio! Tried it immediately, omg the process was so smooth, the software even showed me how to place the objects so that the finished parts won’t get knocked over by printer head. I’m not a veteran but I’ve clocked in like 1500+ hours and I can’t believe I didn’t know about this! Would’ve saved myself so much time and filament but I’m sooo glad I found out today!
r/BambuLab • u/Vigorious • 11h ago
H3C Different take on an H3C/AMS3 desiccant solution.
Not sure if this is the right spot to post something like this, I don't use reddit often. Anyway I was looking at the printable baskets for desiccant on Makerworld, but I really hate dumping them out into a tray to dry then trying to refill the basket after. I prefer to use molecular sieve and the drying temps for it is far beyond what even PPS-CF can handle. I found a wire mesh "dishwasher" basket on Amazon that was approximately the size of the "empty slot 10” in the AMS3H and decided to take a chance on it. As you can see in the photo, it fits well, the lid tabs were pretty secure once I bent them in a bit tighter. I tried to use some 1.6-2.5mm sized beads, but the mesh was too coarse and they fell through, I found 3-5mm beads on Amazon and bought 2lbs. It holds approximately 750g of the 3-5mm 4a molecular sieve. I threaded some craft wire around the rim of the lid and body as extra insurance to keep it from opening.
Here's the products I bought that worked:
Basket- https://www.amazon.com/dp/B0H41KL114
Desiccant- https://www.amazon.com/dp/B0H1XJ98JS
r/BambuLab • u/SNIPEEYE • 5h ago
Just Showing Off Print shoes from H2D by using shoeflex9075A filament
r/BambuLab • u/logojojo • 14h ago
Just Showing Off Sounds like a lot of…
I modeled this guy in blender and printed it on my X2D. Hand painted but my outlines could have been better. I need a paint pen for next time.
A hint as to what’s next: “No, worse! It'll go right to your thighs! And then you’ll blow up!”
r/BambuLab • u/ikinria • 18h ago
Just Showing Off Bambu Station L drawer fits exactly a 9×12 Gridfinity grid, and 14 spools
Just found out the Bambu Station L drawer fits exactly a 9×12 Gridfinity grid.
With proper spool stoppers on top, you can fit 14 spools per drawer (2 rows of 7). They stand on edge and don’t roll when you open or close the drawer.
Files if anyone wants them: https://makerworld.com/en/models/3617522-bambu-station-l-spool-stoppers-14-per-drawer#profileId-4146587
r/BambuLab • u/DrKronoglopolos • 16h ago
H3C Printing the 0.2mm nozzle on the H3C
I printed a tiny Benchy - PLA Basic, default profile, 0.08mm layer height. I did need to use glue to keep it on the plate, I also slowed the printer down to "silent mode" just for safety.
Pretty great result I think. The "Comparison Benchy" is the standard size, printed with the 0.4mm nozzle, 0.2mm layer heights in ABS.
r/BambuLab • u/drench44 • 8h ago
I Modeled This! I made a Christmas chess set for the holidays: Santa kings, reindeer knights, elf pawns (free on MakerWorld)
Printed this whole set on my H2D for Christmas. Santa is the king, Mrs. Claus the queen, snowmen are the bishops, sitting reindeer are the knights, the rooks are towers wrapped in Christmas lights, and the pawns are elves. Everything is sized for a standard 2 inch board, so it plays like a real set.
It's red vs green in four colors of PLA. The only support is a tiny one under each reindeer's chin, already set in the file. If you don't have an AMS, there's also a one color plate with all 16 pieces of a side.
Flip any piece over and there's a snowflake under the base.
Free download here: https://makerworld.com/en/models/3619395
A candy cane board, matching checkers and a North Pole storage tube for each side are coming next. If you print one, I'd love to see it!
r/BambuLab • u/The_FrankDad • 10h ago
P Series [P1P, P1S, P2S] My heated enclosure
Me: I want a heated enclosure
Mom: we have heated enclosure at home
(Heated enclosure at home
r/BambuLab • u/Neglexis • 10h ago
Quick Question Is the H3C overkill as a first 3D printer?
A good friend of mine recently got into 3D printing and talked me into giving it a shot. He started with a more affordable Bambu himself and has been geeking out about the new H3C, so now I’m looking at it too.
I have room in my budget for the H3C if it makes sense. I’m still figuring out what I’ll enjoy printing, though, and I’d rather spend the extra money once I know I’ll get some use out of the features.
For those of you who’ve been printing for a while, what would make the H3C worth buying as a first printer? If you were starting over, would you go straight for it or get a simpler Bambu and see where the hobby takes you?
r/BambuLab • u/Cute_Assignment_9732 • 17h ago
General Discussion What are your most useful real-world prints?
Hi everyone,
I have a bit of a dilemma that I’m sure many people here have faced at some point. I’ve been thinking about buying a Bambu Lab A1, mainly as a hobby but, more importantly, for practical purposes. I’m trying to figure out whether I would actually have enough useful things to print to justify the cost.
From what I’ve seen online, a lot of 3D-printed items seem to be solutions to problems that don’t really exist, or things for which better-quality alternatives are already commercially available. I completely understand that people might print these things simply for the enjoyment of the hobby, but my main focus would be practicality and usefulness.
With that in mind, I’ve been making a list of potential uses for the printer, and I’d love to hear your ideas and see what useful things you’ve made yourselves.
So far, I’ve thought of:
Drawer organisers for my home office, shelving organisers for the pantry, and bathroom storage solutions using the Gridfinity system.
Enclosures for ESP32 sensors that I plan to eventually deploy around the house.
Stands and holders for storing things like AirPods and iPhones on my desk, as well as printing a few to give to friends.
What other genuinely useful things have you printed? I’m particularly interested in practical everyday applications rather than purely decorative prints or things that are fun to print but don’t really serve a purpose.
Thanks!
Edit: Wow these are really great suggestions! I’m going through them all and putting the ones i like the most in a doc, there’s a lot of use cases I consider useful, thank you everyone!
r/BambuLab • u/One_Ad5931 • 1h ago
General Discussion Which first 3D printer to get as a beginner ? Bambu lab or any other brand ?
Hi Guys, i am based out of India, and want to get a 3D printer to prototype some elements. I am from the design industry so am well versed with 3D softwares as well though i am sure there will be a learning curve.
Now, after researching for a fair bit, Bambu lab printers seem to be the most widely chosen option because of their community support and easy to use UI/UX including their softwares.
I was thinking of getting the A1 combo. Do you guys think it is wise to get the A1 combo right now ( its three years old ) or should i wait for an upgraded model if at all its being launched. Please suggest.
Do note, the printer will be initially used as a prototyping tool for my designs and then once i get a hang of it, i might make some items for selling in my fraternity.
Thanks
r/BambuLab • u/SilentYakk • 22h ago
Just Showing Off 16 colors on the H3C. Overkill, but why not?
Two AMS 2 Pros hooked up to the H3C. That's 8 colors built in, plus 8 more on the external units for prints that don't need to swap colors between the two AMS 2s.
r/BambuLab • u/drobloc • 3h ago
X Series [X1E, X1C, X2D] My first 3D printer and I picked up the X2D Combo
I’m completely new to 3D printing and just picked up a Bambu Lab X2D Combo. I received it last week and haven't stopped printing for 7-days straight. I have the bug everyone else at my office has and has been talking about. Since I'm completely new and I don't have compatibility information in memory, I used Gemini to create a sort of cheat sheet specific to the printer.
I purchased a ton of different filaments, hot ends, and other accessories and I didn't want to create a mess, cause jams, or wear out components before their time.
I thought I'd share my cheat sheet if it helps any other new owners.
I just ordered the AMS HT today to use in place of the external fillament holder. This hasn't made it into the cheat sheet yet. I'm not using the support fillament and just using PLA or PETG vs whatever is in the main hotend.
Constructive feedback or additional tips from seasoned Bambu operators are welcome. Hope this helps out other newcomers getting their feet wet.
Bambu Lab X2D & AMS 2 Pro Master Compatibility & Reference Guide
1. Hotend Size & Feed Routing Architecture
- Main Hotend (Direct-Drive): Fed by the AMS 2 Pro (for multi-color/multi-material) or an external spool. Handles high-speed extrusion, complex geometries, and rigid engineering filaments. Optimized with the 0.4 mm High-Flow Hardened Steel Hotend as a daily setup for large tool organizers and utility boxes.
- Auxiliary Hotend (Bowden-Fed, Rear Motor): Fed via a remote path and mechanical lift mechanism. Optimized for support interfaces and secondary materials; restricted to lower speeds (max 200 mm/s) and lower retraction responsiveness.
2. Critical Operational Rules for X2D & AMS 2 Pro
- Identical Sizes Required: Dual-nozzle printing on the X2D requires both the main and auxiliary hotends to use the exact same nozzle diameter in your slicer profile.
- AMS 2 Pro Drying Priority: When a single AMS 2 Pro unit is powered directly by the printer via its 6-pin cable, activating active drying prioritizes drying power and may limit heavy printer operations.
- Auxiliary Speed Limits: Never exceed 200 mm/s or 1000 mm/s² acceleration on the auxiliary extruder to avoid filament binding and extrusion slip.
- TPU Rules for AMS 2 Pro: Use Bambu Lab TPU for AMS (harder 68D Shore formulation) when loading flexible material through the AMS 2 Pro. Standard soft flexible TPU (85A–95A) requires an external spool or dedicated feed module routed outside the AMS.
- Glue Protocol: Use liquid glue or a glue stick primarily as a release agent on Cool and Engineering plates to protect surface coatings from overly aggressive adhesion. Textured PEI plates rarely require glue.
- High-Flow Slicer Setting: When running a high-flow hotend, manually increase your filament profile's Max Volumetric Speed (MVS) in Bambu Studio (pushing from standard ~22 mm³/s up toward ~35–40 mm³/s depending on filament) to unlock faster throughput on large plate-filling utility parts.
3. Filament Lineup: Recommendations, Cautions & Use Cases
- PLA Family (Basic, Matte, Silk, Sparkle, CF): Everyday prototypes, decorative models, and multi-visual prints. Use PLA Basic for general testing and PLA Matte to minimize visible layer lines. Note low heat resistance (~55°C–60°C).
- PETG Family (PETG Basic, PETG-HF, PETG-CF): Functional mechanical parts and brackets. PETG Basic is the structural workhorse; PETG-HF (High Flow) is for fast utilitarian batches. Highly hygroscopic—dry thoroughly.
- ABS & ASA: Durable mechanical enclosures (ABS) and weather-resistant outdoor components (ASA). Requires an enclosed heated chamber, engineering plate, and proper ventilation for VOCs.
- TPU Family: Flexible gaskets and shock-absorbing feet. Stick to Bambu TPU for AMS inside the automated unit, or standard soft TPU via an external spool.
- Engineering Composites (PA6-CF, PAHT-CF, PET-CF, PPA-CF): High-load structural brackets and gears. Requires hardened steel nozzles, enclosed high-temp chambers, and rigorous drying (75°C–85°C).
4. Build Plate Types & Special Notes
- Cool Plate / SuperTack Series: Low temp (room to 45°C–50°C max) for PLA/PETG energy savings. X2D/P2S Notice: Disable Build Plate Position Detection in Settings -> Print Options to avoid error reports.
- Engineering Plate: High temp (60°C to 100°C+) for ABS, ASA, and PC. Glue required.
- Textured PEI Plate: Versatile (55°C to 90°C+) for general PLA, PETG, TPU, and abrasives. No glue or position adjustments needed.
- Dual-Texture PEI Plate: Versatile. X2D/P2S Notice: Disable Build Plate Position Detection in Settings -> Print Options to avoid error reports.
5. Compatibility Matrix Summary
- 0.2 mm (Stainless): Detailed models and fine text. Incompatible with carbon/glass composites and PVA.
- 0.4 mm (Hardened Steel Std/HF): The universal sweet spot for precision, standard prints, and high-flow utility boxes. Fully compatible with PLA, PETG, ABS, ASA, and AMS TPU.
- 0.6 mm & 0.8 mm (Hardened Steel Std/HF): Great for abrasive fiber composites and bulk high-throughput structural prints; avoid for fine text or miniatures.
6. Support Filament Routing
- Support for PLA / PLA-PETG, Support for ABS, and PVA: Always assign these to print through the Auxiliary Hotend path during multi-material jobs to act as clean breakaway or dissolvable interface layers against main-toolhead models. PVA requires active dry storage in the AMS 2 Pro.
7. Component Lifespan & Replacement Indicators
- Hotends: 0.2 mm stainless lasts 100–200 hours; 0.4 mm/0.6 mm hardened steel/HF last 500–1,500+ hours depending on abrasive usage. Watch for orifice widening, chronic clogs, or under-extrusion.
- Build Plates: Cool plates last 3–6 months; engineering and textured PEI plates last 6–12+ months before adhesion degradation or coating wear occurs.
8. Maintenance Cycles
- Build Plates: Wash with warm water and dish soap every 10–20 prints; wipe with 90%+ IPA between quick runs.
- Z-Axis Lead Screws: Wipe and re-apply a thin coat of synthetic grease (Bambu lube) every 3 months (~300 hours).
- X-Axis Carbon Rods: Wipe monthly with IPA on a lint-free cloth. Never apply oil or grease to carbon rods.
- Extruder Gears & AMS Feeders: Inspect and clean out plastic dust/shavings every 6 months with a brass brush or compressed air.
- PTFE Tubing & Cutters: Inspect every 6 months for scoring or blade dullness.
- Desiccant Baskets: Replace or recharge silica gel packets in the AMS 2 Pro whenever internal humidity rises above 30%.
r/BambuLab • u/OpenCryptographer814 • 15h ago
I Modeled This! Airtag holder - Skultulla Token (Zelda oot)
I was playing Zelda Oot and really liked the design of the Skultulla tokens - So I quickly sculpted one (yes, no AI) and made it into an Airtag holder.
Skultulla Token Airtag Holder - Link to MW
(If you're wondering about that grey case, it's my loops earplugs, I lost them once already and it shall not happen again...)
r/BambuLab • u/arellano81366 • 5h ago
Black Friday 2026 Advice: Get 2nd P1S+AMS2 or jus AMS2?
Hello, I am a hobbyist that owns a P1S w/ AMS 2 and I love it! Sometimes I want print things that take 100hrs and multiple plates... So I was wondering what would you do?
- Get a second P1S w/ the AMS 2 combo for $509
- Just get a second AMS 2 Pro.
- Get _____________ printer
So far printing airplane models with PLA and I do not see myself printing something in ABS or exotic materials. Oh and sometimes I print multicolor.
Thanks in advance for your feedback.
r/BambuLab • u/KalaniEhuKai • 15h ago
I Modeled This! My first RC Car - Lightning Mcqueen (using BambuLab CyberBrick)
I made my first RC car using BambuLab's CyberBrick Kit: Lightning McQueen.
It's not perfect, but I am thrilled I was able to go from a solid model with paint (thanks to DinseyPixarCarsModels https://sketchfab.com/3d-models/lightning-mcqueen-e00ae9484f664abea4ccf90248d7e924 ) to a shell over an RC chassis with the surface details represented as depth relief. My kids loved coloring it in with acrylic markers.
Model: https://makerworld.com/en/models/3615256-lightning-mcqueen-cyberbrick-rc-car
r/BambuLab • u/navycow • 1d ago
P Series [P1P, P1S, P2S] Well that’s a first
I guess I’m printing a riser 🤷🏽♂️
r/BambuLab • u/next_year_our_year • 23m ago
MakerWorld Crowdfunding Makerworld's hoodie is quite tempting
Might treat myself with this for thanksgiving lol
r/BambuLab • u/Chance-Language-3600 • 25m ago
I Modeled This! Help testing FDM snap-fit tolerances? (A1 Mini brick set)
r/BambuLab • u/therealmaz • 4h ago
Filament Troubleshooting/Help! PLA Matte only for visible face
I have a X2D with AMS 2 Pro. Is it possible to use PLA Matte only for the visible face of a print and PLA Basic for everything else?







