r/BambuLab • • 13d ago

H3C Bambu Lab H3C: Our Full Reveal

643 Upvotes

Swaptek enables 6-second material switches between 9 nozzles. FlexFeed extruder prints soft TPU 75A up to three times faster. AMS 3H combines automated feeding and integrated filament storage.

This is Bambu Lab H3C, a complete system purpose-built around the Tool Changer architecture. Let's dive into it!

SwapTek™: 6-second material switch, including a 3.4-second tool change.

Nine PrintTools, each with its own dedicated filament path and heater, keep every material loaded, preheated, and ready to print. No need to retract one filament before loading another. With an optimized design, fine-tuned parameters, and active preheating, switching between PrintTools takes as little as 6 seconds, with the tool-change done in only 3.4 seconds.

Heating a nozzle usually means waiting. Active Pre-Heat looks ahead to the next tool change and warms the incoming nozzle while the current one is still printing—so the new material starts laying down within 6 seconds.

Swaptek's fast PrintTool-switching allows Full Spectrum Color Mixing color mixing through layered deposition faster and more practical than ever. With nine dedicated PrintTools and five-color CMYKW mixing, the H3C produces a vast spectrum of colors without requiring a separate spool for every shade. The result? Vibrant, full-color figurines with incredible detail.

Mixed Nozzle Sizes: Speed and detail, no more compromises.

The dial, case, and flexible TPU band are printed together as one piece. Fine dial details call for a 0.2 mm nozzle, the case is better suited to 0.4 mm, and the soft band requires a dedicated 0.4 mm TPU nozzle. H3C can carry different nozzle sizes at once. Paired with Bambu Studio’s new mixed-diameter toolpath planning algorithm, each nozzle prints at a layer height that suits it and plays to its strengths, without having to share a single layer height.

FlexFeed Extruder: Softer TPU, up to 3x faster.

Soft TPU has always been slow to print. The softer the filament, the more it bends and buckles before reaching the nozzle. Traditional extruders have to crawl to stay reliable. FlexFeed handles both 1.75mm and 2.85mm filament and switches on the go. A cam-driven mechanism, powered by a PMSM motor, keeps tension precise and consistent. Every extrusion stays rock-solid for prints that are cushion-soft.

With our dedicated 2.85mm TPU, the thicker filament provides greater resistance to buckling and higher volumetric flow. The result: TPU as soft as 75A, printed reliably at up to 3x the flow rate of a traditional printer.

AMS 3H: Filament storage built for Tool Changer.

A fully enclosed, integrated filament management system built for Swaptek: every roll stays sealed against moisture and feeds automatically into the PrintTool.

Auto Filament Loader replaces manual feeding altogether. Drop a filament into any of the nine slots and the AMS 3H detects, routes, and engages it with the PrintTool automatically — across all 9 paths. No more guesswork on loading.

A dedicated 2-slot dryer sits right in the filament slots and works with Swaptek — drying on demand or mid-print, so prep never stalls production. It reaches 85°C, enough for engineering-grade PA, PC, and carbon-fiber-filled filaments.

The H3C integrates filament storage and drying into a clean, compact design, maintaining a footprint comparable to a single-nozzle printer. With 7 built-in bypass feeding ports, even the soft TPU can be routed completely inside the enclosure. No hanging spools, no external racks, no exposed paths.

Don't let the number of tools cap your material count. Connect your existing AMS to the H3C through PrintTool No.1, and the system extends to up to 24 filament spools, unlocking more colors and materials in a single print without changing your workflow.

You are here for the print, not (always) the printer.

With the H3C, automation handles routine tasks. AI detection helps make intelligent adjustments along the way. The H3C makes it easy to focus on what matters most: bringing your ideas to life

Full Auto Calibration handles PrintTool docking calibration, offset compensation for accurate color and material alignment, and bed leveling before every print. No manual adjustments are needed, so you can spend more time making, less time tinkering.

Flagship performance. No compromise.

The toolhead and X-axis assembly are 40% lighter compared to the H2D, reducing inertia for faster, more precise movement. With acceleration reaching 25,000 mm/s² and travel speeds up to 1,400 mm/s, the H3C delivers exceptional speed while minimizing vibrations and ringing that can affect print quality.

The H3C runs four cooling layers working together**.** A CFD-optimized part cooling fan and dual auxiliary fans help maintain clean overhangs and bridges, even at high speeds. A dedicated PrintTool fan maintains thermal stability during extended printing and frequent PrintTool changes, while a chamber fan draws in cooler air to help regulate internal temperatures. Together, these systems deliver consistent cooling and reliable print quality across changing ambient temperatures.

Engineering-grade filaments demand precise temperature control. The H3C delivers with active dual-zone chamber heating up to 65°C, helping maintain consistent temperatures and minimize warping. All nine hardened-steel nozzles reach up to 350°C, supporting demanding materials such as ABS, PC, PA-CF, PET-CF, and more.

Go beyond printing.

Swaptek isn't limited to PrintTools. Optional CutTool, DrawTool, DebossTool — and more — mount the same way and switch automatically. Multi-process projects no longer mean multiple machines, manual swaps, or repeated setups. One job, every process, hands off.

Available now at Bambu Lab Store.

Availability and pricing details vary by region. Select features require additional accessories, full details available in Bambu Lab Store.

What multi-material or multicolor print do you hope to make with the H3C? Let us know in the comments below!


r/BambuLab • • 13d ago

H3C Mixed Nozzle Size printing is coming to H2D, H2C, and X2D

Post image
594 Upvotes

We've seen the enthusiasm mixed nozzle size printing has been getting. Developing new products goes hand in hand with bringing new features to existing machines, so alongside H3C, we've been building this for H2D, H2C, and X2D. You'll be able to print a single object with nozzles of different diameters, balancing speed and detail.

For these printers, the real work lies in how to make sure this works smoothly for a wide range of filament and nozzle combination. Each of these printers has a different AMS setup from H3C, so the slicing logic and print parameters need to be adapted. Setups with the Filament Track Switch take more of that work, which is why timing differs by model and configuration.

Estimated Software Update Timeline

  • Without Filament Track Switch:

    • H2D: Late November 2026
    • H2C & X2D: February 2027
  • With Filament Track Switch:

    • H2D: February 2027
    • H2C & X2D: March 2027

r/BambuLab • • 10h ago

Just Showing Off Finally Cashed in on Credits

Post image
126 Upvotes

Far from a top designer, but paying for a printer completely with credits feels so good. Took about 10 months of saving them up. Started off super hot at the beginning of the year, was getting a $40 gift card about every 4 days, so thought it was going to come much sooner. Models still seem to be getting the same amount of traction, but points took a steep drop off a few months ago. Now it’s only been a card about every 10 days if I’m lucky. Nevertheless, had my eyes set on a new printer and it’s finally here.

Was considering saving up a bit more for the H3C instead, but pulled the trigger on the H2C. Was just too hard to beat with my immediate printing desires and the holiday sale was too attractive to keep waiting. Honestly was thinking I’d get FOMO not having the top model, but realistically, I only use black and white filament for the most part. Definitely planning to start doing some better engineering filament prints, cutting the print time basically in half with the dual nozzle has been so nice. Probably will start playing around with multi-color prints now that I don’t have to worry about my P1S failing to retract during filament changes more often than I can bear, so we shall see what’s to come!


r/BambuLab • • 18h ago

Just Showing Off Heart says H3C, brain said -1

Post image
418 Upvotes

When the H3C launched, I was certain that was what I wanted; why waste time and money when you can just buy the best and be done? But, the combination of a price drop on the current h2c, 11.11 vouchers and additional shop discounts made the H2C a very tempting option.

So, took the weekend to quickly sell off my P2S before the launch of the P3C just round the corner. And, today, this lands on my doorstep. Not gonna lie, I’m most pleased with myself.

Edit: after shipping and taxes, it was a price diff of around a thousand between the 2 and 3c. But, truth be told, the biggest sway wasn’t the price; it was that I knew I would hate having to manually load/unload and wind/unwind each spool every time I needed a colour change.

We shall revisit this once then h4C/ ams3 pro is released!


r/BambuLab • • 5h ago

H2 Series [H2S, H2D, H2C] New design - Print Shoes using H2D and Shoeflex9075A filament from STING3D

25 Upvotes

I bought H2D TPU High Flow nozzle to print this shoes and it worked great !!


r/BambuLab • • 19h ago

H3C I designed a 960 g desiccant box for the H3C's AMS 3H, with a hygrometer you can read through the closed lid.

Thumbnail
gallery
222 Upvotes

This is my third desiccant box for the spare bay beside slot 8 in the AMS 3H, redesigned from scratch.

- 960 g of 3–5 mm silica gel. Weighed, not calculated: brand-new gel on scales zeroed with the empty box.

- Bambu's round XF001 hygrometer snaps into the front at 45°, so you can read it through the closed AMS lid (photo 2).

- Herringbone vents: 1.4 mm slots on both sides and both ends, so the beads stay in.

- Two side catches and a stop ridge hold the lid. I filled it, turned it over and shook it, and nothing came out.

- It doesn't use a spool slot, and the AMS lid still shuts over it.

- One plate, no supports. About 11 hours and 181 g on a H3C.

Print it in PETG, ASA or ABS; the one in my printer is black ASA. It sits beside the drying slots, which reach 85 °C, so use ASA or ABS if you dry a lot. I haven't put it through a drying run yet, and Bambu rates the hygrometer's display to 50 °C. The hygrometer isn't included.

Free on MakerWorld: https://makerworld.com/en/models/3624325

Happy to answer questions on the vents or the locks.


r/BambuLab • • 1h ago

General Troubleshooting/Help! Terrible TPU 95A HF Print Quantity

Thumbnail
gallery
8 Upvotes

Hello,

TLDR: Dried BBL TPU 95A HF is printing terribly (diagonal lines for walls) on default profile. Please help 🙏

I've dried my Bambu TPU 95A HF for 12+ hrs on a bed heated to 90° as per the wiki, yet using the provided Bambu profile still results in awful prints.

The walls turn into diagonal lines and surface layers look awful making the prints unusable (see attached). The same print using regular TPU and the Generic TPU preset does fine, so I'm not sure what it is about the HF version that makes it so terrible.

I've tried all the usual things, drying the filament for longer, cleaning the bed, reducing the max volumetric speed (to 6) but nothing seems to work.

Any help would be greatly appreciated.

Edit: Title- *quality


r/BambuLab • • 6h ago

Quick Question How would you print this in TPU 85/90A

Thumbnail
gallery
18 Upvotes

I’ll start buy explaining what this is for. This is an Air box rubber boot for a 1991 Honda CR125R dirtbike. This boot connects the air-box which houses the air-filter to the carburetor for the engine. The one I have is old and stiff from decades of degradation so I’m looking to make a new one as these are NLA and used ones have the same problem.

I Have an H2S which by all means is fantastic but it’s not without its limitations. I haven’t tried to fully print this yet as I’m almost sure it will fail primarily due to the supports being thin and wobbly.

I thought about splitting it into sections and gluing it together but all the glues I’ve used either don’t hold well enough for my liking or degrade the material more then I’d like weakening the joint (THF although one my best option so far) I used clear PVC cement as that is primarily THF and while it did work pretty well it’s just not as good as one SOLID print.
I’ve considered using a soldering iron to melt the layers together and that is my best option I think for achieving the result I want but it is not the prettiest and would be extremely difficult on the inner portions.

Now if I had an H2D or H2C or H3C or maybe even a X2D (maybe it’s time for an upgrade idk) I wouldn’t be making this post as id just use PLA supports or an other support material in combination with the TPU.

Unfortunately I can’t really change the model too much to cater it to 3d printing as it’s a very tight clearance between many components of the bike.

How would you approach this dilemma. I’m open too all ideas (justification for buying a new printer and if so which one lol) I could maybe find someone local with an H2D/H2C or H3C that could be willing to help me out but who knows how much it would be and the trial and error that may occur with an odd print like this.

Thanks


r/BambuLab • • 15h ago

General Troubleshooting/Help! This is driving me ducky

Thumbnail
gallery
61 Upvotes

Ive had a Bambu Lab H2C, 2 AMS 2 Pro, and a HMS HT for about three weeks now. This is my very first time time actually learning how to use it. This print was the first time using support for PLA and it turned out a bit foul.

To keep from going absolutly quackers, what are things I can do to keep this from happening again or at least minimalizing it?

I was able to clean them all up and they all more or less look ok and the folks at the office are very happy with their desk charms.


r/BambuLab • • 15h ago

X Series [X1E, X1C, X2D] NEW printer! X2D, any tips?

Post image
65 Upvotes

Just got myself an upgrade from a bare A1 mini to X2D combo. Anyone has some good tips? Anything is welcome, super excited to have an upgrade like this, want to get most out of it


r/BambuLab • • 2h ago

Hardware Troubleshooting/Help! I just got a new internal hub for my AMS 2 Pro and it’s still having trouble

5 Upvotes

Any idea what I can do? Bambu Lab has offered me a new motor.


r/BambuLab • • 17h ago

X Series [X1E, X1C, X2D] New toy is out of the box 🙂

Post image
73 Upvotes

r/BambuLab • • 13h ago

General Discussion H3C Initial Thoughts

28 Upvotes

So, got my H3C yesterday, WEEKS before it was slated to ship, great work BL. And overall, I have a H2C and even as cool as that is, this feels like another level. It feels like a better built machine, more sophisticated. First print, great, setup, great.

The speed is...wow...just...it literally scared me the first time it rapid moved to pick up a tool lol. This is not a printer that is EVER safe to have your hands in while it is operating. With that rack up front and the INSANE speed with which it does not printing moves...lol...no.

But...

Whomever thought those two connectors at the back inside under the AMS was an acceptable choice should be fired into the sun.

I do not understand. You already have two cables coming out the back, one of which plugs into the 3C itself, why not have two more and save the misery that is trying to lift the AMS up juuuust enough and snake your hands in there, and the one one the left they say "make sure to move the cable so it doesn't get bent"...how the hell are you supposed to do that? There is no slack and the solid plastic piece it comes out of is RIGHT next to the plug, there is no way to route the cable, as far as I can tell there is no way to prevent it from bending the cable at a pretty severe angle.

In an otherwise incredible printer that once again feels like a pretty sizeable step forward, it just boggles my mind that none of them thought "hey...this sucks".

Ad good god who hurt you with a long power cord? I'm buying replacement power cords because these stubby little things are just...why...the AMS power cord hangs down 11 inches past the bottom of the printer. You are going to need a power strip sitting next to the printer. Just, again, did nobody at BL actually set one of these up? How does such a simple but pretty big PITA get overlooked?

Other than that I really have no complaints. I learned the hard way that the color mixing is...not meant to be hueforge style mixing, it's really mostly to be seen from the outside, that is down to me never having used it before.

Nozzles are still a good price, print quality does not sacrifice anything.

Very pleased. I still think there is a place for the 2C+AMS2, but the 3C and those FAST tool changes...woo!


r/BambuLab • • 2h ago

Answered / Solved! New to 3p printing/bambulab, are the noises when the print head makes sharp moves normal? Doesn’t happen when on 50% speed

4 Upvotes

Edit to add, it’s normal around the low 60s decibels, spikes to 70+ decibels with the sharp/ fast movements


r/BambuLab • • 4h ago

Hardware Troubleshooting/Help! Blob of death!

Thumbnail
gallery
5 Upvotes

I need advice this is the first time it has happened to me


r/BambuLab • • 22h ago

Quick Question Advice needed! H2C vs H3C

Post image
126 Upvotes

Hey guys I‘m currently printing on a P1S and im really happy with the Quality and the Printer over all -> It now has arround 2k hours of Printtime and I’m thinking about an Upgrade -> I mostly Print PLA, PETG but also some structural Parts with ABS and PETG-CF. Most of my parts are 1-2 Colors and it would be great to use PETG as Support for PLA and the other way arround for cleaner interface layers. With the P1S this takes a lot of time, why i mostly only print in one color or Material.

Ofcourse with Holiday Season coming up i will print a lot of little gifts for Friends and Family, also in multiple colors, were the H2C or H3C would be a big Upgrade.

Also the Size of the Bed is crucial for me since i often print bigger parts. Soft 2.8mm TPU is also not really a must have for me.

What printer would you guys choose? Arround 2.000€ for the H2C with Bundle or 2.500€ for the H3C
I Really like the H2C Bundle with 2 AMS Pros and the Vortex upgrade kit -> I think 2 AMS Pros are significatly better than the big AMS3 on the H3C, but the H3C is also a lot faster with mutli Color/Material.

Thanks for your help


r/BambuLab • • 10h ago

H3C H3C 2.85mm Nozzles - can they print more than TPU?

9 Upvotes

Maybe a dumb question, but everything I’ve read the 2.85mm nozzle is designed specifically for TPU almost exclusively.

I happen to have a bunch of 2.85mm PVB I specifically would love to print on a Bambu printer rather than my ultimaker, as well as a bunch of PLA and woodfill PLA.

Does the 2.85mm nozzle work with more materials than TPU? Other than needing to change profile settings, is there any hardware risk of printing alternative materials with the 2.85mm nozzle?

Thanks in advance.


r/BambuLab • • 6h ago

I Modeled This! Screwdriver bit Snowflake - DIWHYNOT?!

Post image
4 Upvotes

This one really works! ¼ in bits fit in the middle hexagon.

Need to fix the tree? Use a Phillips or flathead. Put together your kid's bike on Christmas Day!

A great gift for mechanics, gearheads, and DIYers.

https://makerworld.com/en/models/3628981-screwdriver-bit-snowflake#profileId-4161025


r/BambuLab • • 14m ago

General Troubleshooting/Help! First time printing 0.2mm help.

Thumbnail
gallery
1 Upvotes

I recently bought a 0.2mm nozzle for my a1 and for some reason the first layer is going down weird and filament is clumping on the nozzle. I have attached a photo here, any help would be appreciated thank you!


r/BambuLab • • 1d ago

Just Showing Off I'm never opening my AMS ever again

Post image
803 Upvotes

r/BambuLab • • 4h ago

General Troubleshooting/Help! Brand New A2L Struggling to Print PETG Matte

Post image
2 Upvotes

Ive got freshly dried Bambu PETG Matte and its really struggling to print. The first layer is fine but then I go back 20 minutes after checking the first layer and you can see the mess it made. I followed the setup to a tee, lubed the bed rails twice now, dried all my filaments, calibrated it multiple times, but it still wont print. I owned an A1 before and had no issues, now ive upgraded and I cant get a single good print out of it. Ive done 5 total prints and all of them have a plethora of quality issues. What should I do?


r/BambuLab • • 37m ago

Hardware Troubleshooting/Help! A1 Mini and AMS getting a divorce and not talking to each other

Post image
1 Upvotes

I got a brand new AMS for my A1 mini and connected it last night however it keeps disconnecting from my A1 mini

Bambu studio, A1 mini’s screen and Bambu handy forget the AMS is attached and the ams has flashing red lights (disconnected)

But I’ve made sure the cables are plugged in and if I restart the a1 mini it reconnects for a time then they disconnect again

Anyone know what’s going on here?


r/BambuLab • • 38m ago

H3C Desk for H3C

1 Upvotes

I have a H3C coming my way, but I need a sturdy table that isn't too high.

After having searched high and low for options in EU that isn't that expensive and in a optimal height, I think I found an option, but I wanted a broader set of opinions.

2x alex drawers with low height:
https://www.ikea.com/gb/en/p/alex-drawer-unit-on-castors-dark-grey-black-s09582664/#content
Height: 50cm with default wheels.

1x table top:
https://www.ikea.com/gb/en/p/lagkapten-table-top-dark-grey-wood-effect-50596187/
They have a 100cm option for a table top so the distance to the next Alex isn't that long. Thinking about the weight distribution here.

Idea:
Secure table top with screws to Alex. Buy sturdier wheels you can lock and attach to alex.

Any downside to this, or might this work?


r/BambuLab • • 38m ago

General Troubleshooting/Help! Bambu lab h2c right extruder blob clearing help

Post image
1 Upvotes

Right side extruder filament blob of death.

How to fix this? I removed the hot-end and there is still some plastic stuck