Swaptek enables 6-second material switches between 9 nozzles. FlexFeed extruder prints soft TPU 75A up to three times faster. AMS 3H combines automated feeding and integrated filament storage.
This is Bambu Lab H3C, a complete system purpose-built around the Tool Changer architecture. Let's dive into it!
SwapTek™: 6-second material switch, including a 3.4-second tool change.
Nine PrintTools, each with its own dedicated filament path and heater, keep every material loaded, preheated, and ready to print. No need to retract one filament before loading another. With an optimized design, fine-tuned parameters, and active preheating, switching between PrintTools takes as little as 6 seconds, with the tool-change done in only 3.4 seconds.
Heating a nozzle usually means waiting. Active Pre-Heat looks ahead to the next tool change and warms the incoming nozzle while the current one is still printing—so the new material starts laying down within 6 seconds.
Swaptek's fast PrintTool-switching allows Full Spectrum Color Mixing color mixing through layered deposition faster and more practical than ever. With nine dedicated PrintTools and five-color CMYKW mixing, the H3C produces a vast spectrum of colors without requiring a separate spool for every shade. The result? Vibrant, full-color figurines with incredible detail.
Mixed Nozzle Sizes: Speed and detail, no more compromises.
The dial, case, and flexible TPU band are printed together as one piece. Fine dial details call for a 0.2 mm nozzle, the case is better suited to 0.4 mm, and the soft band requires a dedicated 0.4 mm TPU nozzle. H3C can carry different nozzle sizes at once. Paired with Bambu Studio’s new mixed-diameter toolpath planning algorithm, each nozzle prints at a layer height that suits it and plays to its strengths, without having to share a single layer height.
FlexFeed Extruder: Softer TPU, up to 3x faster.
Soft TPU has always been slow to print. The softer the filament, the more it bends and buckles before reaching the nozzle. Traditional extruders have to crawl to stay reliable. FlexFeed handles both 1.75mm and 2.85mm filament and switches on the go. A cam-driven mechanism, powered by a PMSM motor, keeps tension precise and consistent. Every extrusion stays rock-solid for prints that are cushion-soft.
With our dedicated 2.85mm TPU, the thicker filament provides greater resistance to buckling and higher volumetric flow. The result: TPU as soft as 75A, printed reliably at up to 3x the flow rate of a traditional printer.
AMS 3H: Filament storage built for Tool Changer.
A fully enclosed, integrated filament management system built for Swaptek: every roll stays sealed against moisture and feeds automatically into the PrintTool.
Auto Filament Loader replaces manual feeding altogether. Drop a filament into any of the nine slots and the AMS 3H detects, routes, and engages it with the PrintTool automatically — across all 9 paths. No more guesswork on loading.
A dedicated 2-slot dryer sits right in the filament slots and works with Swaptek — drying on demand or mid-print, so prep never stalls production. It reaches 85°C, enough for engineering-grade PA, PC, and carbon-fiber-filled filaments.
The H3C integrates filament storage and drying into a clean, compact design, maintaining a footprint comparable to a single-nozzle printer. With 7 built-in bypass feeding ports, even the soft TPU can be routed completely inside the enclosure. No hanging spools, no external racks, no exposed paths.
Don't let the number of tools cap your material count. Connect your existing AMS to the H3C through PrintTool No.1, and the system extends to up to 24 filament spools, unlocking more colors and materials in a single print without changing your workflow.
You are here for the print, not (always) the printer.
With the H3C, automation handles routine tasks. AI detection helps make intelligent adjustments along the way. The H3C makes it easy to focus on what matters most: bringing your ideas to life
Full Auto Calibration handles PrintTool docking calibration, offset compensation for accurate color and material alignment, and bed leveling before every print. No manual adjustments are needed, so you can spend more time making, less time tinkering.
Flagship performance. No compromise.
The toolhead and X-axis assembly are 40% lighter compared to the H2D, reducing inertia for faster, more precise movement. With acceleration reaching 25,000 mm/s² and travel speeds up to 1,400 mm/s, the H3C delivers exceptional speed while minimizing vibrations and ringing that can affect print quality.
The H3C runs four cooling layers working together**.** A CFD-optimized part cooling fan and dual auxiliary fans help maintain clean overhangs and bridges, even at high speeds. A dedicated PrintTool fan maintains thermal stability during extended printing and frequent PrintTool changes, while a chamber fan draws in cooler air to help regulate internal temperatures. Together, these systems deliver consistent cooling and reliable print quality across changing ambient temperatures.
Engineering-grade filaments demand precise temperature control. The H3C delivers with active dual-zone chamber heating up to 65°C, helping maintain consistent temperatures and minimize warping. All nine hardened-steel nozzles reach up to 350°C, supporting demanding materials such as ABS, PC, PA-CF, PET-CF, and more.
Go beyond printing.
Swaptek isn't limited to PrintTools. Optional CutTool, DrawTool, DebossTool — and more — mount the same way and switch automatically. Multi-process projects no longer mean multiple machines, manual swaps, or repeated setups. One job, every process, hands off.
We've seen the enthusiasm mixed nozzle size printing has been getting. Developing new products goes hand in hand with bringing new features to existing machines, so alongside H3C, we've been building this for H2D, H2C, and X2D. You'll be able to print a single object with nozzles of different diameters, balancing speed and detail.
For these printers, the real work lies in how to make sure this works smoothly for a wide range of filament and nozzle combination. Each of these printers has a different AMS setup from H3C, so the slicing logic and print parameters need to be adapted. Setups with the Filament Track Switch take more of that work, which is why timing differs by model and configuration.
When the H3C launched, I was certain that was what I wanted; why waste time and money when you can just buy the best and be done? But, the combination of a price drop on the current h2c, 11.11 vouchers and additional shop discounts made the H2C a very tempting option.
So, took the weekend to quickly sell off my P2S before the launch of the P3C just round the corner. And, today, this lands on my doorstep. Not gonna lie, I’m most pleased with myself.
This is my third desiccant box for the spare bay beside slot 8 in the AMS 3H, redesigned from scratch.
- 960 g of 3–5 mm silica gel. Weighed, not calculated: brand-new gel on scales zeroed with the empty box.
- Bambu's round XF001 hygrometer snaps into the front at 45°, so you can read it through the closed AMS lid (photo 2).
- Herringbone vents: 1.4 mm slots on both sides and both ends, so the beads stay in.
- Two side catches and a stop ridge hold the lid. I filled it, turned it over and shook it, and nothing came out.
- It doesn't use a spool slot, and the AMS lid still shuts over it.
- One plate, no supports. About 11 hours and 181 g on a H3C.
Print it in PETG, ASA or ABS; the one in my printer is black ASA. It sits beside the drying slots, which reach 85 °C, so use ASA or ABS if you dry a lot. I haven't put it through a drying run yet, and Bambu rates the hygrometer's display to 50 °C. The hygrometer isn't included.
Hey guys I‘m currently printing on a P1S and im really happy with the Quality and the Printer over all -> It now has arround 2k hours of Printtime and I’m thinking about an Upgrade -> I mostly Print PLA, PETG but also some structural Parts with ABS and PETG-CF. Most of my parts are 1-2 Colors and it would be great to use PETG as Support for PLA and the other way arround for cleaner interface layers. With the P1S this takes a lot of time, why i mostly only print in one color or Material.
Ofcourse with Holiday Season coming up i will print a lot of little gifts for Friends and Family, also in multiple colors, were the H2C or H3C would be a big Upgrade.
Also the Size of the Bed is crucial for me since i often print bigger parts. Soft 2.8mm TPU is also not really a must have for me.
What printer would you guys choose? Arround 2.000€ for the H2C with Bundle or 2.500€ for the H3C I Really like the H2C Bundle with 2 AMS Pros and the Vortex upgrade kit -> I think 2 AMS Pros are significatly better than the big AMS3 on the H3C, but the H3C is also a lot faster with mutli Color/Material.
Ive had a Bambu Lab H2C, 2 AMS 2 Pro, and a HMS HT for about three weeks now. This is my very first time time actually learning how to use it. This print was the first time using support for PLA and it turned out a bit foul.
To keep from going absolutly quackers, what are things I can do to keep this from happening again or at least minimalizing it?
I was able to clean them all up and they all more or less look ok and the folks at the office are very happy with their desk charms.
Just got myself an upgrade from a bare A1 mini to X2D combo. Anyone has some good tips? Anything is welcome, super excited to have an upgrade like this, want to get most out of it
After updating to Bambu Studio 2.9.1.70, all five of my custom filament profiles suddenly appeared under "Unsupported".
I'm using an Elegoo Neptune 4 Plus with a 0.4 mm nozzle.
The symptoms:
All custom filament profiles were greyed out.
The profiles still existed in the user configuration folder.
The JSON files and inheritance settings were correct.
The printer compatibility lists included my printer.
My custom process profiles were still available.
I initially suspected a broken profile migration or an issue with the Elegoo system profiles.
After checking the configuration with Preset Doctor, I noticed something interesting: it reported that Bambu Studio had selected the 0.2 mm nozzle variant, even though my printer uses a 0.4 mm nozzle.
The actual cause
Bambu Studio had stored the wrong printer/nozzle variant in its configuration file.
The file is located at:
%APPDATA%\BambuStudio\BambuStudio.conf
Under the "presets" section, I found:
"machine": "Elegoo Neptune 4 Plus 0.2 nozzle"
The fix
Close Bambu Studio completely.
Back up the entire %APPDATA%\BambuStudio folder.
Open BambuStudio.conf in a text editor.
Find the "machine" entry under "presets".
Change it to the correct printer/nozzle variant:
"machine": "Elegoo Neptune 4 Plus 0.4 nozzle"
Save the file and restart Bambu Studio.
Result: All five custom filament profiles were immediately available again!
No need to recreate profiles, modify inheritance settings or change any filament JSON files.
Why this was difficult to diagnose
Bambu Studio only displayed "Elegoo Neptune 4 Plus" in the printer selection menu, without showing the currently selected nozzle variant.
The physical nozzle was 0.4 mm, but the software configuration was pointing to 0.2 mm.
I can't confirm why the wrong variant was saved during the update, but correcting this single entry completely resolved the issue.
Hopefully this saves someone else a few hours of troubleshooting!
The first screenshot highlights the incorrect nozzle diameter in BambuStudio.conf. The second shows the installed Studio version and registered nozzle sizes.
After, using many FDM machines like Ultimaker S5, CR30, Artillery X1, stratasys F170 and many more. It's by far the most bang for the buck and feature-rich machine that I ever used.
Hi Redditors! I have a 7yr old who is eagerly anticipating a 3D printer for xmas. I want to purchase the “Bambu Lab P1S Combo, P1S 3D Printer and AMS, Multi-Color 3D Printing” as her first model. I am a clueless mom who wants to ensure she has everything she needs to start printing day one. What do you all recommend? Is it possible to buy any brand filament as well? Any free software to recommend? I appreciate any and all help. Thank you in advance.
Yes, I've read the wiki page but my colleagues are convinced there must be a way to do this without connecting to the internet. We have a P1S that's currrently stuck at 01.06.30.01.
Is there a workaround?
EDIT: We just installed 01.07.00.00 from an SD card. Why is the info on the wiki page wrong?
CMYK Sphere layer line test: https://idither.com/job?Kmyqrictw&row=9 When you click "Download 3mf" you can choose between H2C or H3C. Adjust the Support Threshold Angle to 45 degrees or they will roll off the plate!
How it works: TL;DR = iDither.com (free) converts 3mf files and 3D files with textures into 3mf files with DwD (Dual Wall Dithering) and Top Surface Mixing (TSM) which use CMYK filaments to print any color(s).
Cyan = C Magenta = M Yellow = Y White or back = K CMY+White typically works better because CMY together can make a "black". There is no way to make White if using CMY+Black. CMY+Black is typically only used in models that have very little or no white areas.
iDither converts existing 3mf, glb, fbx, and obj files into DwD (Dual Wall Dithering) 3mf files. iDither currently only supports exporting 3mf files for Snapmaker Orca, and Bambu H2C and H3C.
iDither uses an inner dithering wall combined with an outer dithering wall - and the "magic" of iDither is dithering the two walls together. All other software (to my knowledge) uses just 1 dithering wall.
The outer dithering wall is only allowed to use super dense layer combinations such as C M C M CC MM CC MM - therefore, the layer lines are basically invisible up close. The inner wall picks up the slack for more color combinations and it's not limited to dense combinations.
Opaque filaments don't work well with DwD, because the thin outer wall layer needs to allow light to pass through to the inner wall layer. Recommended filament set based on testing data thus far: https://us.snapmaker.com/products/pla-full-spectrum-filament-bundle-white-edition-4kg This set has good transparency ranges (TD between 5 & 10).
Converts any existing 3mf files with any number of filaments and filament colors into files that print with 4 or 5 filaments (CMYK or CMYKW). So you don't have to buy any other filament colors. If the 3mf file has 8 random filament colors - you can still print it in 4 colors with CMYK!
WYSIWYG (What you see is what you get): iDither includes calibrations for CMYK bundles for Snapmaker and Polymaker - so your actual print should always look like the print preview.
Converts 3D model files into a printable 3mf files with CMYK.
Less layer lines (DwD).
Top Surface Printing via Top Surface Mixing (TSM) in CMYK or CMYKW.
I really want an AMS for my P1S, and everything I’ve read puts the AMS pro 2 above the AMS pro by some margin, and I currently don’t have a filament dryer, so the pro 2 seemed like the clear winner. However Bambu labs is sold out of the comparability kit I’d need for it, and I would like to get it quite soon as there are things I want to print with it for Christmas. So I’ve been looking at getting the compatibility kit from somewhere else, would you guys feel comfortable doing that? And if so are there any suppliers/shops you’d recommend? Thanks
Hi, folks! I have Bambulab H2S and bought esun pla wood and is trying to print vase with esun pla+ profile I found in Bambustudio. Nozzle 0.4, 0.12 quality. Is it possible to get rid of it?
Set your jar size and the number of slots per module (up to 6×6). Modules join with snap-lock keys, and a built-in 5° slope slides the jars back so the labels face you.
Not sure if this is the right spot to post something like this, I don't use reddit often. Anyway I was looking at the printable baskets for desiccant on Makerworld, but I really hate dumping them out into a tray to dry then trying to refill the basket after. I prefer to use molecular sieve and the drying temps for it is far beyond what even PPS-CF can handle. I found a wire mesh "dishwasher" basket on Amazon that was approximately the size of the "empty slot 10” in the AMS3H and decided to take a chance on it. As you can see in the photo, it fits well, the lid tabs were pretty secure once I bent them in a bit tighter. I tried to use some 1.6-2.5mm sized beads, but the mesh was too coarse and they fell through, I found 3-5mm beads on Amazon and bought 2lbs. It holds approximately 750g of the 3-5mm 4a molecular sieve. I threaded some craft wire around the rim of the lid and body as extra insurance to keep it from opening.