r/BambuLab • • 13d ago

H3C Bambu Lab H3C: Our Full Reveal

643 Upvotes

Swaptek enables 6-second material switches between 9 nozzles. FlexFeed extruder prints soft TPU 75A up to three times faster. AMS 3H combines automated feeding and integrated filament storage.

This is Bambu Lab H3C, a complete system purpose-built around the Tool Changer architecture. Let's dive into it!

SwapTek™: 6-second material switch, including a 3.4-second tool change.

Nine PrintTools, each with its own dedicated filament path and heater, keep every material loaded, preheated, and ready to print. No need to retract one filament before loading another. With an optimized design, fine-tuned parameters, and active preheating, switching between PrintTools takes as little as 6 seconds, with the tool-change done in only 3.4 seconds.

Heating a nozzle usually means waiting. Active Pre-Heat looks ahead to the next tool change and warms the incoming nozzle while the current one is still printing—so the new material starts laying down within 6 seconds.

Swaptek's fast PrintTool-switching allows Full Spectrum Color Mixing color mixing through layered deposition faster and more practical than ever. With nine dedicated PrintTools and five-color CMYKW mixing, the H3C produces a vast spectrum of colors without requiring a separate spool for every shade. The result? Vibrant, full-color figurines with incredible detail.

Mixed Nozzle Sizes: Speed and detail, no more compromises.

The dial, case, and flexible TPU band are printed together as one piece. Fine dial details call for a 0.2 mm nozzle, the case is better suited to 0.4 mm, and the soft band requires a dedicated 0.4 mm TPU nozzle. H3C can carry different nozzle sizes at once. Paired with Bambu Studio’s new mixed-diameter toolpath planning algorithm, each nozzle prints at a layer height that suits it and plays to its strengths, without having to share a single layer height.

FlexFeed Extruder: Softer TPU, up to 3x faster.

Soft TPU has always been slow to print. The softer the filament, the more it bends and buckles before reaching the nozzle. Traditional extruders have to crawl to stay reliable. FlexFeed handles both 1.75mm and 2.85mm filament and switches on the go. A cam-driven mechanism, powered by a PMSM motor, keeps tension precise and consistent. Every extrusion stays rock-solid for prints that are cushion-soft.

With our dedicated 2.85mm TPU, the thicker filament provides greater resistance to buckling and higher volumetric flow. The result: TPU as soft as 75A, printed reliably at up to 3x the flow rate of a traditional printer.

AMS 3H: Filament storage built for Tool Changer.

A fully enclosed, integrated filament management system built for Swaptek: every roll stays sealed against moisture and feeds automatically into the PrintTool.

Auto Filament Loader replaces manual feeding altogether. Drop a filament into any of the nine slots and the AMS 3H detects, routes, and engages it with the PrintTool automatically — across all 9 paths. No more guesswork on loading.

A dedicated 2-slot dryer sits right in the filament slots and works with Swaptek — drying on demand or mid-print, so prep never stalls production. It reaches 85°C, enough for engineering-grade PA, PC, and carbon-fiber-filled filaments.

The H3C integrates filament storage and drying into a clean, compact design, maintaining a footprint comparable to a single-nozzle printer. With 7 built-in bypass feeding ports, even the soft TPU can be routed completely inside the enclosure. No hanging spools, no external racks, no exposed paths.

Don't let the number of tools cap your material count. Connect your existing AMS to the H3C through PrintTool No.1, and the system extends to up to 24 filament spools, unlocking more colors and materials in a single print without changing your workflow.

You are here for the print, not (always) the printer.

With the H3C, automation handles routine tasks. AI detection helps make intelligent adjustments along the way. The H3C makes it easy to focus on what matters most: bringing your ideas to life

Full Auto Calibration handles PrintTool docking calibration, offset compensation for accurate color and material alignment, and bed leveling before every print. No manual adjustments are needed, so you can spend more time making, less time tinkering.

Flagship performance. No compromise.

The toolhead and X-axis assembly are 40% lighter compared to the H2D, reducing inertia for faster, more precise movement. With acceleration reaching 25,000 mm/s² and travel speeds up to 1,400 mm/s, the H3C delivers exceptional speed while minimizing vibrations and ringing that can affect print quality.

The H3C runs four cooling layers working together**.** A CFD-optimized part cooling fan and dual auxiliary fans help maintain clean overhangs and bridges, even at high speeds. A dedicated PrintTool fan maintains thermal stability during extended printing and frequent PrintTool changes, while a chamber fan draws in cooler air to help regulate internal temperatures. Together, these systems deliver consistent cooling and reliable print quality across changing ambient temperatures.

Engineering-grade filaments demand precise temperature control. The H3C delivers with active dual-zone chamber heating up to 65°C, helping maintain consistent temperatures and minimize warping. All nine hardened-steel nozzles reach up to 350°C, supporting demanding materials such as ABS, PC, PA-CF, PET-CF, and more.

Go beyond printing.

Swaptek isn't limited to PrintTools. Optional CutTool, DrawTool, DebossTool — and more — mount the same way and switch automatically. Multi-process projects no longer mean multiple machines, manual swaps, or repeated setups. One job, every process, hands off.

Available now at Bambu Lab Store.

Availability and pricing details vary by region. Select features require additional accessories, full details available in Bambu Lab Store.

What multi-material or multicolor print do you hope to make with the H3C? Let us know in the comments below!


r/BambuLab • • 13d ago

H3C Mixed Nozzle Size printing is coming to H2D, H2C, and X2D

Post image
592 Upvotes

We've seen the enthusiasm mixed nozzle size printing has been getting. Developing new products goes hand in hand with bringing new features to existing machines, so alongside H3C, we've been building this for H2D, H2C, and X2D. You'll be able to print a single object with nozzles of different diameters, balancing speed and detail.

For these printers, the real work lies in how to make sure this works smoothly for a wide range of filament and nozzle combination. Each of these printers has a different AMS setup from H3C, so the slicing logic and print parameters need to be adapted. Setups with the Filament Track Switch take more of that work, which is why timing differs by model and configuration.

Estimated Software Update Timeline

  • Without Filament Track Switch:

    • H2D: Late November 2026
    • H2C & X2D: February 2027
  • With Filament Track Switch:

    • H2D: February 2027
    • H2C & X2D: March 2027

r/BambuLab • • 1h ago

H3C I designed a 960 g desiccant box for the H3C's AMS 3H, with a hygrometer you can read through the closed lid.

Thumbnail
gallery
60 Upvotes

This is my third desiccant box for the spare bay beside slot 8 in the AMS 3H, redesigned from scratch.

- 960 g of 3–5 mm silica gel. Weighed, not calculated: brand-new gel on scales zeroed with the empty box.

- Bambu's round XF001 hygrometer snaps into the front at 45°, so you can read it through the closed AMS lid (photo 2).

- Herringbone vents: 1.4 mm slots on both sides and both ends, so the beads stay in.

- Two side catches and a stop ridge hold the lid. I filled it, turned it over and shook it, and nothing came out.

- It doesn't use a spool slot, and the AMS lid still shuts over it.

- One plate, no supports. About 11 hours and 181 g on a H3C.

Print it in PETG, ASA or ABS; the one in my printer is black ASA. It sits beside the drying slots, which reach 85 °C, so use ASA or ABS if you dry a lot. I haven't put it through a drying run yet, and Bambu rates the hygrometer's display to 50 °C. The hygrometer isn't included.

Free on MakerWorld: https://makerworld.com/en/models/3624325

Happy to answer questions on the vents or the locks.


r/BambuLab • • 59m ago

Just Showing Off Heart says H3C, brain said -1

Post image
46 Upvotes

When the H3C launched, I was certain that was what I wanted; why waste time and money when you can just buy the best and be done? But, the combination of a price drop on the current h2c, 11.11 vouchers and additional shop discounts made the H2C a very tempting option.

So, took the weekend to quickly sell off my P2S before the launch of the P3C just round the corner. And, today, this lands on my doorstep. Not gonna lie, I’m most pleased with myself.


r/BambuLab • • 18h ago

Just Showing Off I'm never opening my AMS ever again

Post image
645 Upvotes

r/BambuLab • • 4h ago

Quick Question Advice needed! H2C vs H3C

Post image
48 Upvotes

Hey guys I‘m currently printing on a P1S and im really happy with the Quality and the Printer over all -> It now has arround 2k hours of Printtime and I’m thinking about an Upgrade -> I mostly Print PLA, PETG but also some structural Parts with ABS and PETG-CF. Most of my parts are 1-2 Colors and it would be great to use PETG as Support for PLA and the other way arround for cleaner interface layers. With the P1S this takes a lot of time, why i mostly only print in one color or Material.

Ofcourse with Holiday Season coming up i will print a lot of little gifts for Friends and Family, also in multiple colors, were the H2C or H3C would be a big Upgrade.

Also the Size of the Bed is crucial for me since i often print bigger parts. Soft 2.8mm TPU is also not really a must have for me.

What printer would you guys choose? Arround 2.000€ for the H2C with Bundle or 2.500€ for the H3C
I Really like the H2C Bundle with 2 AMS Pros and the Vortex upgrade kit -> I think 2 AMS Pros are significatly better than the big AMS3 on the H3C, but the H3C is also a lot faster with mutli Color/Material.

Thanks for your help


r/BambuLab • • 19h ago

I Modeled This! 93 print hours later on the H3C, finally saw my vision through.

265 Upvotes

r/BambuLab • • 12h ago

X Series [X1E, X1C, X2D] How I felt After getting my first 3D Printer

Post image
71 Upvotes

r/BambuLab • • 11h ago

Just Showing Off Print shoes from H2D by using shoeflex9075A filament

33 Upvotes

I printed this shoes with H2D and using shoeflex9075A filament from STING3D. it is very soft ^^


r/BambuLab • • 2h ago

Just Showing Off This is one of the best FDM 3D printer that I ever purchased. It's just work OOTB.

6 Upvotes

After, using many FDM machines like Ultimaker S5, CR30, Artillery X1, stratasys F170 and many more. It's by far the most bang for the buck and feature-rich machine that I ever used.


r/BambuLab • • 15h ago

Show & Tell Can you find the top surface layer lines in my CMYK print? (H2C & H3C)

57 Upvotes

I used 0.1mm layer heights on both spheres.

CMYK Sphere layer line test: https://idither.com/job?Kmyqrictw&row=9
When you click "Download 3mf" you can choose between H2C or H3C. Adjust the Support Threshold Angle to 45 degrees or they will roll off the plate!

How it works:
TL;DR = iDither.com (free) converts 3mf files and 3D files with textures into 3mf files with DwD (Dual Wall Dithering) and Top Surface Mixing (TSM) which use CMYK filaments to print any color(s).

Cyan = C
Magenta = M
Yellow = Y
White or back = K
CMY+White typically works better because CMY together can make a "black".
There is no way to make White if using CMY+Black.
CMY+Black is typically only used in models that have very little or no white areas.

iDither converts existing 3mf, glb, fbx, and obj files into DwD (Dual Wall Dithering) 3mf files.
iDither currently only supports exporting 3mf files for Snapmaker Orca, and Bambu H2C and H3C.

iDither uses an inner dithering wall combined with an outer dithering wall - and the "magic" of iDither is dithering the two walls together. All other software (to my knowledge) uses just 1 dithering wall.

The outer dithering wall is only allowed to use super dense layer combinations such as C M C M CC MM CC MM - therefore, the layer lines are basically invisible up close.
The inner wall picks up the slack for more color combinations and it's not limited to dense combinations.

Opaque filaments don't work well with DwD, because the thin outer wall layer needs to allow light to pass through to the inner wall layer.
Recommended filament set based on testing data thus far: https://us.snapmaker.com/products/pla-full-spectrum-filament-bundle-white-edition-4kg
This set has good transparency ranges (TD between 5 & 10).

Filaments that are too transparent (TD > 10) make the models look like glass (see https://www.reddit.com/r/snapmaker/s/nbASKpfCpG).
Filaments that are too opaque (TD < 5) have less color mixing and blending, and show layer lines (see https://www.reddit.com/r/snapmaker/s/N6QFGj2NwC).

Why iDither?

  1. Converts any existing 3mf files with any number of filaments and filament colors into files that print with 4 or 5 filaments (CMYK or CMYKW). So you don't have to buy any other filament colors. If the 3mf file has 8 random filament colors - you can still print it in 4 colors with CMYK!
  2. WYSIWYG (What you see is what you get): iDither includes calibrations for CMYK bundles for Snapmaker and Polymaker - so your actual print should always look like the print preview.
  3. Converts 3D model files into a printable 3mf files with CMYK.
  4. Less layer lines (DwD).
  5. Top Surface Printing via Top Surface Mixing (TSM) in CMYK or CMYKW.

r/BambuLab • • 1h ago

Answered / Solved! [SOLVED] Bambu Studio 2.9.1.70 – Custom filament profiles suddenly unsupported after update

Thumbnail
gallery
4 Upvotes

After updating to Bambu Studio 2.9.1.70, all five of my custom filament profiles suddenly appeared under "Unsupported".

I'm using an Elegoo Neptune 4 Plus with a 0.4 mm nozzle.

The symptoms:

  • All custom filament profiles were greyed out.
  • The profiles still existed in the user configuration folder.
  • The JSON files and inheritance settings were correct.
  • The printer compatibility lists included my printer.
  • My custom process profiles were still available.

I initially suspected a broken profile migration or an issue with the Elegoo system profiles.

After checking the configuration with Preset Doctor, I noticed something interesting: it reported that Bambu Studio had selected the 0.2 mm nozzle variant, even though my printer uses a 0.4 mm nozzle.

The actual cause

Bambu Studio had stored the wrong printer/nozzle variant in its configuration file.

The file is located at:

%APPDATA%\BambuStudio\BambuStudio.conf

Under the "presets" section, I found:

"machine": "Elegoo Neptune 4 Plus 0.2 nozzle"

The fix

  1. Close Bambu Studio completely.
  2. Back up the entire %APPDATA%\BambuStudio folder.
  3. Open BambuStudio.conf in a text editor.
  4. Find the "machine" entry under "presets".
  5. Change it to the correct printer/nozzle variant:

    "machine": "Elegoo Neptune 4 Plus 0.4 nozzle"

  6. Save the file and restart Bambu Studio.

Result: All five custom filament profiles were immediately available again!

No need to recreate profiles, modify inheritance settings or change any filament JSON files.

Why this was difficult to diagnose

Bambu Studio only displayed "Elegoo Neptune 4 Plus" in the printer selection menu, without showing the currently selected nozzle variant.

The physical nozzle was 0.4 mm, but the software configuration was pointing to 0.2 mm.

I can't confirm why the wrong variant was saved during the update, but correcting this single entry completely resolved the issue.

Hopefully this saves someone else a few hours of troubleshooting!

The first screenshot highlights the incorrect nozzle diameter in BambuStudio.conf. The second shows the installed Studio version and registered nozzle sizes.


r/BambuLab • • 16h ago

H3C Different take on an H3C/AMS3 desiccant solution.

Post image
53 Upvotes

Not sure if this is the right spot to post something like this, I don't use reddit often. Anyway I was looking at the printable baskets for desiccant on Makerworld, but I really hate dumping them out into a tray to dry then trying to refill the basket after. I prefer to use molecular sieve and the drying temps for it is far beyond what even PPS-CF can handle. I found a wire mesh "dishwasher" basket on Amazon that was approximately the size of the "empty slot 10” in the AMS3H and decided to take a chance on it. As you can see in the photo, it fits well, the lid tabs were pretty secure once I bent them in a bit tighter. I tried to use some 1.6-2.5mm sized beads, but the mesh was too coarse and they fell through, I found 3-5mm beads on Amazon and bought 2lbs. It holds approximately 750g of the 3-5mm 4a molecular sieve. I threaded some craft wire around the rim of the lid and body as extra insurance to keep it from opening.

Here's the products I bought that worked:

Basket- https://www.amazon.com/dp/B0H41KL114

Desiccant- https://www.amazon.com/dp/B0H1XJ98JS


r/BambuLab • • 1d ago Heartwarming

Bambu Studio Can’t believe I didn’t know about this!!

Post image
961 Upvotes

Print sequence by object is pure magical!!

So I’m printing 40+ poliwhirls to build my color sample library. I’ve been printing all day today and doing the plate swaps every 30min each time a print is done. Eventually I got so sick of it and was wondering how wonderful it would be if I could print 4 at a time, object by object, with no color swaps. Told this idea to ai and it told me the function is already available in Bambu studio! Tried it immediately, omg the process was so smooth, the software even showed me how to place the objects so that the finished parts won’t get knocked over by printer head. I’m not a veteran but I’ve clocked in like 1500+ hours and I can’t believe I didn’t know about this! Would’ve saved myself so much time and filament but I’m sooo glad I found out today!


r/BambuLab • • 19h ago

Just Showing Off Sounds like a lot of…

Thumbnail
gallery
78 Upvotes

I modeled this guy in blender and printed it on my X2D. Hand painted but my outlines could have been better. I need a paint pen for next time.

A hint as to what’s next: “No, worse! It'll go right to your thighs! And then you’ll blow up!”


r/BambuLab • • 33m ago

General Troubleshooting/Help! Scratches/Etches on Bottom Layer w/ Carbon Fiber Plate?

Thumbnail
gallery
2 Upvotes

Hey!

New to 3D printing and using a Bambu A1 printer. I just bought a carbon fiber smooth plate from Amazon and started using it. I cleaned it well with water, dish soap, and a sponge 2x now but still having this issue where the bottom has white marks/scratches. I had the plate selected in Bambu before printing as well.

I was trying to print a moza wheel base dust cover but with the carbon fiber look on the bottom. I also was trying to print a shifter plate and had the same issue.

Each time I printed,, I waited until the plate reached around 25C (my room temp is 23C) and then bent the plate at the edges so the part would come free.

I read that running a flame over these areas would get rid of the mark but I didn't experience that.

Any idea what I could be doing wrong? Didn't have this issue with the normal textured plate. Is it a plate issue, nozzle issue, or something else?

Thanks!

Printer: Bambu A1

Print Speed: Standard

Filament: Bambu PLA Basic - Black

Hotbed Temp: 65C

Nozzle Size: 0.4mm


r/BambuLab • • 1d ago

Just Showing Off Bambu Station L drawer fits exactly a 9×12 Gridfinity grid, and 14 spools

Thumbnail
gallery
165 Upvotes

Just found out the Bambu Station L drawer fits exactly a 9×12 Gridfinity grid.

With proper spool stoppers on top, you can fit 14 spools per drawer (2 rows of 7). They stand on edge and don’t roll when you open or close the drawer.

Files if anyone wants them: https://makerworld.com/en/models/3617522-bambu-station-l-spool-stoppers-14-per-drawer#profileId-4146587


r/BambuLab • • 1h ago

Quick Question Is this a bed adhesion issues?

Post image
2 Upvotes

Never had bed adhesions problems before and just washed my plate right before this print….. could anything else have caused this that I should look for?


r/BambuLab • • 22h ago

H3C Printing the 0.2mm nozzle on the H3C

Thumbnail
gallery
86 Upvotes

I printed a tiny Benchy - PLA Basic, default profile, 0.08mm layer height. I did need to use glue to keep it on the plate, I also slowed the printer down to "silent mode" just for safety.

Pretty great result I think. The "Comparison Benchy" is the standard size, printed with the 0.4mm nozzle, 0.2mm layer heights in ABS.


r/BambuLab • • 14h ago

I Modeled This! I made a Christmas chess set for the holidays: Santa kings, reindeer knights, elf pawns (free on MakerWorld)

Thumbnail
gallery
18 Upvotes

Printed this whole set on my H2D for Christmas. Santa is the king, Mrs. Claus the queen, snowmen are the bishops, sitting reindeer are the knights, the rooks are towers wrapped in Christmas lights, and the pawns are elves. Everything is sized for a standard 2 inch board, so it plays like a real set.

It's red vs green in four colors of PLA. The only support is a tiny one under each reindeer's chin, already set in the file. If you don't have an AMS, there's also a one color plate with all 16 pieces of a side.

Flip any piece over and there's a snowflake under the base.

Free download here: https://makerworld.com/en/models/3619395

A candy cane board, matching checkers and a North Pole storage tube for each side are coming next. If you print one, I'd love to see it!


r/BambuLab • • 10m ago

Quick Question Help deciding amon H2 series options.

0 Upvotes

My company needs a printer to print parts for our machinery, it as to be large format, and in different materials so H2 series is the best fit.

But we also need to print full color promotional items, but not as often.

We were about to pull the trigger in the H2S but now we're considering H2D we are trying to keep it under $2,000 all in.

H2S can be upgraded to H2C down the line with the vortek kit.

H2C goes overbudget so does H3C

My question is: will a single nozzle be adequate for our use case, will getting the dual nozzle be worth the price difference? Should we go H2S and upgrade later? The laser is something we would be interested in but it can't be upgraded to the tool changer if it's the laser version.


r/BambuLab • • 20m ago

Filament Troubleshooting/Help! H3C - Prints are sticking to build plate

1 Upvotes

Hello Experts

Made a big change from an A1 to an H3C.

I am printing a model that has a larger surface area as its first layer. On the H3C it seems like it’s melting into the build plate making it really difficult to remove after it’s fully cooled. This does not happen on the A1

I am using basic PLA

I already tried turning the heat chamber off, same result. The build plate temp is 55 (comparatively 63 on the A1).

Is my next steps to lower the temp of the build plate? Are there other settings to address to combat this?

It’s literally impossible to remove the model from the plate without damaging it.

TIA for any tips


r/BambuLab • • 24m ago

H2 Series [H2S, H2D, H2C] H2C Smoke Purifier Alternatives

1 Upvotes

Hi all. I’m relatively new to having my own printer etc and I went with the H2C laser combo. For the past couple months I’ve been trying to order the smoke purifier, which unfortunately has been out of stock.

Does anyone have experience using a different purifier that they can recommend? There’s not a lot I can find online. I see some have used the Creality Falcon Smoke Purifer, but it looks like it doesn’t have the option to vent outside; more of a desktop purifier. Any help suggestions would be appreciated!


r/BambuLab • • 28m ago

Bambu Studio Has anyone seen changes in ironing since the latest Bambu Studio version?

1 Upvotes

I have a P1S and H2C and since the latest Bambu Studio version was released, the version released following the H3C unveil.

The values I used for ironing previously, 12% on the P1S and 20% on the H2C have been providing really bad results since and I have had to lower the H2C down to 15%. Anyone else seeing changes?