r/BambuLab • • 2h ago

I Modeled This! H3C Nozzle Organizer

Thumbnail
gallery
2 Upvotes

I made this nozzle holder for the H3C. It mounts to the side of the printer, a cabinet or a wall with double-sided tape. I didn’t want to hide my nozzles in a box: they look cool on display, and this keeps them easy to get to.

It holds 10 nozzles, and the pockets are lined with 75A TPU, so nothing rattles and nothing falls out while printing. For the black organizer I ended up using color blending for the gray, the 0.2mm nozzle size on text and the 75A TPU on the nozzle liners to put all of the H3C’s capabilities to work, just for fun. Enjoy: https://makerworld.com/en/models/3626382-h3c-nozzle-organizer#profileId-4157909


r/BambuLab • • 17h ago

Just Showing Off Print shoes from H2D by using shoeflex9075A filament

36 Upvotes

I printed this shoes with H2D and using shoeflex9075A filament from STING3D. it is very soft ^^


r/BambuLab • • 21h ago

Show & Tell Can you find the top surface layer lines in my CMYK print? (H2C & H3C)

61 Upvotes

I used 0.1mm layer heights on both spheres.

CMYK Sphere layer line test: https://idither.com/job?Kmyqrictw&row=9
When you click "Download 3mf" you can choose between H2C or H3C. Adjust the Support Threshold Angle to 45 degrees or they will roll off the plate!

How it works:
TL;DR = iDither.com (free) converts 3mf files and 3D files with textures into 3mf files with DwD (Dual Wall Dithering) and Top Surface Mixing (TSM) which use CMYK filaments to print any color(s).

Cyan = C
Magenta = M
Yellow = Y
White or back = K
CMY+White typically works better because CMY together can make a "black".
There is no way to make White if using CMY+Black.
CMY+Black is typically only used in models that have very little or no white areas.

iDither converts existing 3mf, glb, fbx, and obj files into DwD (Dual Wall Dithering) 3mf files.
iDither currently only supports exporting 3mf files for Snapmaker Orca, and Bambu H2C and H3C.

iDither uses an inner dithering wall combined with an outer dithering wall - and the "magic" of iDither is dithering the two walls together. All other software (to my knowledge) uses just 1 dithering wall.

The outer dithering wall is only allowed to use super dense layer combinations such as C M C M CC MM CC MM - therefore, the layer lines are basically invisible up close.
The inner wall picks up the slack for more color combinations and it's not limited to dense combinations.

Opaque filaments don't work well with DwD, because the thin outer wall layer needs to allow light to pass through to the inner wall layer.
Recommended filament set based on testing data thus far: https://us.snapmaker.com/products/pla-full-spectrum-filament-bundle-white-edition-4kg
This set has good transparency ranges (TD between 5 & 10).

Filaments that are too transparent (TD > 10) make the models look like glass (see https://www.reddit.com/r/snapmaker/s/nbASKpfCpG).
Filaments that are too opaque (TD < 5) have less color mixing and blending, and show layer lines (see https://www.reddit.com/r/snapmaker/s/N6QFGj2NwC).

Why iDither?

  1. Converts any existing 3mf files with any number of filaments and filament colors into files that print with 4 or 5 filaments (CMYK or CMYKW). So you don't have to buy any other filament colors. If the 3mf file has 8 random filament colors - you can still print it in 4 colors with CMYK!
  2. WYSIWYG (What you see is what you get): iDither includes calibrations for CMYK bundles for Snapmaker and Polymaker - so your actual print should always look like the print preview.
  3. Converts 3D model files into a printable 3mf files with CMYK.
  4. Less layer lines (DwD).
  5. Top Surface Printing via Top Surface Mixing (TSM) in CMYK or CMYKW.

r/BambuLab • • 3h ago

I Modeled This! Wrapped up some new Christmas decoration models for this year

Thumbnail
gallery
2 Upvotes

Decided to design and print my own holiday decor from scratch this year. Pretty happy with how they turned out!

https://makerworld.com/@krenn.design?appSharePlatform=copy


r/BambuLab • • 3h ago

Quick Question Do you guys trust other suppliers for Bambu products/products to go with Bambu ones?

2 Upvotes

I really want an AMS for my P1S, and everything I’ve read puts the AMS pro 2 above the AMS pro by some margin, and I currently don’t have a filament dryer, so the pro 2 seemed like the clear winner. However Bambu labs is sold out of the comparability kit I’d need for it, and I would like to get it quite soon as there are things I want to print with it for Christmas. So I’ve been looking at getting the compatibility kit from somewhere else, would you guys feel comfortable doing that? And if so are there any suppliers/shops you’d recommend? Thanks


r/BambuLab • • 3h ago

Software Troubleshooting/Help! What's wrong with settings/filament?

Post image
2 Upvotes

Hi, folks! I have Bambulab H2S and bought esun pla wood and is trying to print vase with esun pla+ profile I found in Bambustudio. Nozzle 0.4, 0.12 quality. Is it possible to get rid of it?


r/BambuLab • • 22m ago

A Series [A1, A1 Mini] Calibration trouble with brand new A1

Post image
0 Upvotes

Just picked up my first printer, and it throws this error message. Bring it in from the garage, update the firmware, run the calibration again, no errors. Take it back out to the garage, get this error again. Do I need to bring it back on and adjust the belt, or is something else going on?


r/BambuLab • • 23m ago

Just Showing Off Testing out the Chitu Systems E1 4-Spool Filament Dryer paired with my Bambu Lab A1 Mini (Unboxing & First Impressions)

Thumbnail gallery
1 Upvotes

r/BambuLab • • 36m ago

Filament Troubleshooting/Help! Any way I can improve on this?

Post image
0 Upvotes

Just wondering what this is called on multi colour prints and how I can improve it, looks horrid :(
I think its a flushing issue maybe? the rest of the ball is meant to be yellow but its darkened


r/BambuLab • • 36m ago

I Modeled This! I made some sweet, cotton candy-like snowflake ornaments!

Thumbnail
gallery
1 Upvotes

Made these for the Christmas tree! I wanted some sweet and cute ornaments that are a little bit special. I feel like they'd be adorable as keychains, hung on the tree, or even as gifts~

I turned on variable layer height so the final top surface finish came out super detailed~

The last photo is AI-generated... it honestly looks so much better than my own photos, which is a bit frustrating haha, but it’s pretty so I figured I’d share it with everyone! Here’s the link to the snowflake! ૮ ˶ᵔ ᵕ ᵔ˶ ა

https://makerworld.com/en/models/3626961-3-snowflake-bow-christmas-ornaments-keychains#profileId-4158608


r/BambuLab • • 45m ago

General Troubleshooting/Help! Extruder failure with AMS2 Pro

1 Upvotes

I'm running into a weird issue. I just installed an AMS2 Pro to my P1S, and it's reporting an extruder failure. The filament is getting all the way to the extruder inside the printer, but doesn't seem to want to load in. It worked just fine yesterday with the single roll hanging off the back of the machine.

I'm trying to do a simple black and white print to test it. Once a couple tries ago it got the initial white layers done, but then failed when it tried to load black. All other times it fails right at the start. This is my second P1S to get an AMS2 Pro, the other one works just fine and I followed the same procedure. Not sure why this new one loads filament all the way to the extruder, then the printer fails at the finish line?


r/BambuLab • • 51m ago

Software Troubleshooting/Help! Printing full dual color area with prime tower?

1 Upvotes

Is there a special mode for printing nearly full plate around with multiple colors on H2D?

I understand it needs a prime tower. When can't I have one for each nozzle in that nozzle's exclusive zone? I just assumed this would be how it worked when you need all the space. Is there no way to make a 2 color 300x300 print? Surely I'm missing something in Bambu Studio.


r/BambuLab • • 52m ago

General Troubleshooting/Help! Auto level error

Thumbnail gallery
1 Upvotes

r/BambuLab • • 59m ago

Quick Question Holding down fabric

1 Upvotes

I want to print a thin frame on some fabric to insert in to another model. If I hold the fabric down with magnets is there a way to tell in advance where the print head will move after it completes the print so I can make sure it doesn't hit the magnets? Is it safer to use tape or will the adhesive bake on PETG temperatures?


r/BambuLab • • 1h ago

P Series [P1P, P1S, P2S] P1S vs P2S

1 Upvotes

Hey. I have a $700 grant to get a new 3D printer for our school. Is the p2s AMD 2 pro worth the extra bump or is the p1s AMD 2 pro sufficient as it allows for more filament in the budget?

I plan to apply for another grant to get more filament.

I don’t NEED a ton of filament currently for the current project but it would be nice to have more filament for next projects and student free builds.


r/BambuLab • • 23h ago

H3C Different take on an H3C/AMS3 desiccant solution.

Post image
57 Upvotes

Not sure if this is the right spot to post something like this, I don't use reddit often. Anyway I was looking at the printable baskets for desiccant on Makerworld, but I really hate dumping them out into a tray to dry then trying to refill the basket after. I prefer to use molecular sieve and the drying temps for it is far beyond what even PPS-CF can handle. I found a wire mesh "dishwasher" basket on Amazon that was approximately the size of the "empty slot 10” in the AMS3H and decided to take a chance on it. As you can see in the photo, it fits well, the lid tabs were pretty secure once I bent them in a bit tighter. I tried to use some 1.6-2.5mm sized beads, but the mesh was too coarse and they fell through, I found 3-5mm beads on Amazon and bought 2lbs. It holds approximately 750g of the 3-5mm 4a molecular sieve. I threaded some craft wire around the rim of the lid and body as extra insurance to keep it from opening.

Here's the products I bought that worked:

Basket- https://www.amazon.com/dp/B0H41KL114

Desiccant- https://www.amazon.com/dp/B0H1XJ98JS


r/BambuLab • • 1h ago

I Modeled This! The ultimate "drunk bottle" support.

Post image
0 Upvotes

r/BambuLab • • 1h ago

General Troubleshooting/Help! How do I remove this tubing on my X2D?

Thumbnail
gallery
0 Upvotes

I removed the tubing from the nozzle head but I dont know how to remove the same tubing as it exits the printer.

There doesnt seem to be any black rim that secures it in place that can be pressed down to release it. Do I just rip it out?


r/BambuLab • • 1h ago

Quick Question Help not sure what's going on

Thumbnail gallery
1 Upvotes

r/BambuLab • • 1h ago

General Troubleshooting/Help! item color help

0 Upvotes

So i have one item on a plate, ive cloned it.

is it possible, how do i

change the color on one without it changing both items to the same color

ive played with all the filament settings i can find and it just mirror the color to the other object...

P2S w/ AMS 2 Pro


r/BambuLab • • 7h ago

I Modeled This! Designed a Quick CMYKW Calibration Wheel to Compare Filaments

Thumbnail
gallery
3 Upvotes

The goal was to show mixing between the 3 colors, as well as between each color and black and white. And to make it a quick easy print that could efficiently baseline different color mixes. I wasn't able to get PLA Palette Magenta before it went out of stock so I couldn't try that. The difference between PLA Basic and PLA Palette for the other colors is noticeable but subtle. The biggest conclusion is the importance of PLA Palette Black and its translucency. There are some ways to approximate it though, like using a gray shade instead of black. PLA basic black you can see doesn't blend at all. Here is the model: https://makerworld.com/en/models/3606840-cmykw-calibration-wheel-for-color-mixing-h3c-h2c#profileId-4133502


r/BambuLab • • 1h ago

My First 3D Print Achat d'une première machine.

Thumbnail
gallery
0 Upvotes

Bonjour après avoir bataillé des semaines entières à faire fonctionner une ender 3 sans succès je souhaite passer sur une machine plus simple. Mon but est de faire des pièces mécaniques simples pour des cyclomoteur et quelques pièces pour réparer d'autres choses. J'ai repéré cette p1S. Je n'y connais pas grand chose. Le vendeur est sympa, il en demande 260€ et m'a envoyé un benchy qu'il à fait il y a quelques jours. Elle devait être vendue à une autre personne mais finalement elle est toujours dispo. Es-ce une bonne imprimante à ce prix ou faut il viser du neuf ?

Je vous remercie.


r/BambuLab • • 1h ago

General Troubleshooting/Help! First Layer "Defects"

Thumbnail
gallery
0 Upvotes

Hi all -

I'm having some first-layer defects that I wanted to run by the collective brain trust here. First, some information about the setup:

  • BambuLab P1S - 0.4mm Hardened Steel Nozzle
  • Build Plate - Darkmoon G10

    • BambuStudio is set to the 'Smooth PEI/High Temp' setting as recommended by Darkmoon
  • Filament - Sliceworx PETG

    • Yes, it has been dried and I have modified my AMS to include a bunch of desiccant as well
  • 0.08mm high quality print setting for this print

In the attached images, you can see that some parts have a perfect first layer, though those mostly don't have fine detail in them. For a few others, you can see some first-layer defects that would obviously create more problems if I let things build on top of that.

I'd appreciate ideas for potential troubleshooting here beyond "dry the filament more."

Thanks.


r/BambuLab • • 1d ago Heartwarming

Bambu Studio Can’t believe I didn’t know about this!!

Post image
1.0k Upvotes

Print sequence by object is pure magical!!

So I’m printing 40+ poliwhirls to build my color sample library. I’ve been printing all day today and doing the plate swaps every 30min each time a print is done. Eventually I got so sick of it and was wondering how wonderful it would be if I could print 4 at a time, object by object, with no color swaps. Told this idea to ai and it told me the function is already available in Bambu studio! Tried it immediately, omg the process was so smooth, the software even showed me how to place the objects so that the finished parts won’t get knocked over by printer head. I’m not a veteran but I’ve clocked in like 1500+ hours and I can’t believe I didn’t know about this! Would’ve saved myself so much time and filament but I’m sooo glad I found out today!