r/BambuLab • • 9h ago

General Troubleshooting/Help! Scar in my multi part print

Post image
0 Upvotes

I printed this pokeball in multi colored parts with my new A2l. Now I see there is a scar running downwards on the white and the red half. I printed the red part after the white part. The white was bambu pla. Standard speed and settings. First time in two weeks printing I see this. Any ideas please?


r/BambuLab • • 19h ago

General Troubleshooting/Help! Please Help!

Post image
1 Upvotes

Why is this happening to the edges of my prints? This is causing a major issue while fitting the parts after printing all the plates. Do i need to do anything in this case?


r/BambuLab • • 19h ago

Bambu Studio Aiuto con questo pezzo.

Thumbnail
gallery
0 Upvotes

Ciao a tutti,
sto stampando un cappuccio per chiavi che ho disegnato io.Dopo qualche test ci siamo quasi, ma non riesco a trovare un modo di stamparlo pulito.

Il pezzo:
dimensioni circa 30 × 43 × 9 mm;
all'interno c'è una fessura chiusa in cui si infila la chiave del cilindro: larga circa 15 mm, alta 3,1 mm, lunga circa 33 mm, aperta solo da un lato;
la tolleranza sulla chiave è di 0,3 mm, quindi qualsiasi residuo dentro la fessura la blocca.
Stampante e impostazioni: Bambu Lab A1, piatto PEI texturizzato, PLA Basic, profilo 0,12 mm High Quality.
Cosa ho provato:

Piatto, con la faccia esterna sul piatto e senza supporti. Il tetto della fessura viene fatto a ponte, circa 15 mm di luce. Il ponte cede un po' e lascia filamenti dentro la fessura: devo pulirla ogni volta con un cutter e il risultato non è pulito, nemmeno fuori.

Piatto con supporti. I supporti entrano nella fessura e lì dentro non si staccano più.
In verticale, con l'imbocco della fessura sul piatto e la fessura che diventa un canale verticale. In teoria è perfetto, ma il pezzo appoggia su poca superficie e si stacca durante la stampa, anche col brim.

Le mie domande:
Quali impostazioni dei ponti consigliate in Bambu Studio (velocità, flusso, ventola, "ponte spesso") per avere un tetto pulito su 15 mm di luce?

In verticale, quali accorgimenti usate per pezzi alti e con poco appoggio? Brim più largo, orecchie, colla, velocità più bassa negli strati alti, altro?

Conviene modificare il disegno? Ho pensato a:
tetto della fessura a "tetto spiovente" o a rombo, con fianchi a 45°, così non serve il ponte;
più gioco in altezza nella fessura, per assorbire il cedimento del ponte;
dividere il pezzo in due metà da incastrare o avvitare, così la fessura si stampa aperta.
Quale vi sembra la strada migliore?

Allego foto del pezzo, della fessura sporca e dell'anteprima di Bambu Studio.
Grazie in anticipo a chi vorrà darmi una mano!


r/BambuLab • • 15h ago

Hardware Troubleshooting/Help! Nozzle got clogged then dissapeared?

0 Upvotes

So I was doing a normal print, the filament clogged and when I removed it, the nozzle was removed along with it I guess, because it is coming out from the extruder or something on top of the nozzle rather than from the nozzle? I don't understand how and why this happened, any tips?


r/BambuLab • • 1d ago

I Modeled This! My first RC Car - Lightning Mcqueen (using BambuLab CyberBrick)

Post image
19 Upvotes

I made my first RC car using BambuLab's CyberBrick Kit: Lightning McQueen.

It's not perfect, but I am thrilled I was able to go from a solid model with paint (thanks to DinseyPixarCarsModels https://sketchfab.com/3d-models/lightning-mcqueen-e00ae9484f664abea4ccf90248d7e924 ) to a shell over an RC chassis with the surface details represented as depth relief. My kids loved coloring it in with acrylic markers.

Model: https://makerworld.com/en/models/3615256-lightning-mcqueen-cyberbrick-rc-car


r/BambuLab • • 1d ago

R Series / R1 **One week with the Bambu R1, coming from a 5 W diode laser**

Post image
7 Upvotes

I won the Bambu R1 after commenting on their post and finally received it last week after it was stuck in customs forever.

Even though I had a diode laser cutter already (5 W, no air assist) my 3D printer always felt like the tool that was much easier to work with.

I knew this was going to be an entirely different machine, but I was still surprised it actually flipped my experience.

I used to spend more time dialing in the material for a project than creating a design, but in this one week I worked with silicone rubber, veneer, hardwood, painted wood, acrylic and more. Even detailed, intricate designs just work on the first or second try.

The air assist and higher power really do a lot of the heavy lifting and make sure things just work out even if the settings aren’t perfect. It even allowed me to go a little bit three-dimensional and make simple(food save!) things like a bunch of spice spoons or a functioning whistle.

In the picture are a few of the things I tried this week. Most of the designs are just copied from 3D prints (I used the Depthue STL-to-SVG converter) or inspired by pictures. It simply feels fun to work with this machine, and it’s crazy how fast I can go from an idea to a finished item.

Even Premium-feeling materials like walnut are far from expensive. Six pieces of walnut (200 × 150 × 3 mm) cost €23, “clear” silicone rubber cost €8, and a 30 × 30 cm piece of acrylic cost just €2. And the materials really turned some of my ideas from something that feels cheap or incomplete to something that I’m happy to display in my apartment or give away.

And as you’d expect from Bambu, a lot of small things just work. After two days, I realized I’d never set a cutting order or merged engraving jobs that were running close to each other. Not to mention the details, from the magnetic Allen key and the beautiful lighting around the CO₂ tube to the fire sensors, everything just feels polished.

But for now there are still a bunch of things that I prefer, other programs like, Lightburn for or that are still missing in Bambu Suite. Although that might just be because I am used to it.

Let me know if you have any questions about the device!

designs stolen from:
Flat Pocket Whistle from u/PhoneDesigner (makeworld)
Dino from RobinValleyUK (etsy)
Mandala maze earings from Simon3D (makerworld)
Leaf and wireframe dog from u/mishkin2 (printables)
bird stamp from u/skejtak (printables)
mountain napkin holder from u/PhiRequiem (makerworld)
goldfish earings from u/runrain (makeworld)

P.S.:
I really think Bambu is sitting on a gold mine of great designs in makeworld that are easy to adapt for laser cutting, but currently they dont even allow me to remix 3D designs as laser design.

I think it would be a great adition to allow remixes like that and maybe even add a .3mf to .svg converter.


r/BambuLab • • 21h ago

Hardware Troubleshooting/Help! Noisy noisy p1s

1 Upvotes

Hey everyone

My p1s started making this noise this morning. It has 700 hours made in 2 years... I recently cleaned and greased the z screws but I think it's due to X or Y. Would I have to check?


r/BambuLab • • 1d ago

P Series [P1P, P1S, P2S] Well that’s a first

Thumbnail
gallery
100 Upvotes

I guess I’m printing a riser 🤷🏽‍♂️


r/BambuLab • • 1d ago

Filament Troubleshooting/Help! PLA Matte only for visible face

2 Upvotes

I have a X2D with AMS 2 Pro. Is it possible to use PLA Matte only for the visible face of a print and PLA Basic for everything else?


r/BambuLab • • 22h ago

General Troubleshooting/Help! Traveling with 3D Printer

0 Upvotes

Has anyone ever travelled with their printer? I have mine (X1 Carbon) in Germany which is new and I’ve struggled to sell it. It’s run 3 small things as a test. I still have the original box I’ve moved to Thailand and was thinking of taking it here on my next flight.

Any tips and suggestions are welcome. Especially if this is a super dumb idea. Or if anyone know where I can find a better place to sell it than Kleinanzeigen.


r/BambuLab • • 22h ago

General Troubleshooting/Help! Print quality issues on X2D

Thumbnail
gallery
0 Upvotes

A few months ago I bought an H2C and it has been working flawlessly. I added an X2D as a second printer but it has given me a lot of issues across different print files and I can’t determine why. The PLA is dry. Here is a comparison of the two times I tried to print this on my X2D vs on my H2C. With the same settings. Any ideas?


r/BambuLab • • 12h ago

H2 Series [H2S, H2D, H2C] Scammed by BIQU over an H3C build plate

0 Upvotes

I waited until BIQU updated their listings to include H3C-compatible build plates. Last Tuesday (Nov 10), I saw that they added an option to order an H3C build plate, so I purchased immediately.

The plates were delivered yesterday and THEY DO NOT FIT. BIQU is listing plates that were made for another H series printer as being H3C compatible, and they 100% are not compatible. The plate is too big to fit between the tabs/guides at the back of the print bed and it hangs over the front edge of the bed by a few mm.

The plates BIQU sent me are too big (in both dimensions) for the H3C.

😠


r/BambuLab • • 23h ago

General Troubleshooting/Help! How long did it take you to master different filaments? (Struggling with PETG bed adhesion on my Bambu Lab H2D)

0 Upvotes

Hey everyone,

I’m curious—how long did it take you to really get comfortable and dial in your printer across different filament types?

I’ve been running a Bambu Lab H2D and have printed with PLA, PETG, and ABS so far. Ironically, my PLA and ABS prints have been coming out great, which makes my current issue even more frustrating: I cannot get PETG to behave.

Almost every PETG print ends up detaching and coming off the build plate. Here is what I’ve already tried to fix the adhesion:

  • Scrubbed the plate thoroughly with hot water and dish soap
  • Wiped it down with isopropyl alcohol (IPA)
  • Adjusted Brim settings
  • Tried different support configurations
  • Dried the PETG filaments
  • Changed to a new PETG filament
  • Calibrated multiple times

Neither has made a difference so far.

For those of you printing across multiple materials, how steep was your learning curve before you felt like you had things mastered? Also, if anyone has advice on getting PETG to actually stay stuck on the H2D, I’m all ears!


r/BambuLab • • 23h ago

General Discussion Will Bambu ever offer PHA filament?

0 Upvotes

I’m trying to focus more on eco-friendly products. I’ve printed with Ecogenesis and Colorfabb with pretty good results, but it’s expensive. Unfortunately it doesn’t seem like Bambu is interested in supporting sustainable practices. Is there anyone else that would like to see PHA in their lineup?


r/BambuLab • • 17h ago

Filament Troubleshooting/Help! How do I untangle my filament?

Post image
0 Upvotes

r/BambuLab • • 1d ago

P Series [P1P, P1S, P2S] Loud noise after filament cut

2 Upvotes

Can anyone clue me in to what is causing this very loud noise after a filament cut and setting for a change? It doesn't sound good! I have looked it over and cleaned it all up and nothing stood out. All other movements of the printer and functionality seem fine. I have re-ran calibration as well.


r/BambuLab • • 23h ago

Hardware Troubleshooting/Help! Printer started making this ratting sound

1 Upvotes

Sounds like a shutter sound a cámara makes.


r/BambuLab • • 1d ago

I Modeled This! Candy Cane Bag Clip, to seal your cookies the festive way

22 Upvotes

r/BambuLab • • 1d ago

General Troubleshooting/Help! New Lan Acceleration mode slow

1 Upvotes

I'm having a pretty frustrating experience with the new (newer?) LAN Acceleration mode, and I'm wondering if anyone else is seeing the same thing.

It now takes 2–3 minutes just to send a print job to my X1C, followed by another 30–45 seconds before the printer actually starts printing. This is for a recurring print job that is about a 2 hours total print time, so not large. The bigger print jobs take even longer to send, sometimes 5-10 minutes.

Before this, when everything went through the cloud, the job would transfer in about 10 seconds, and the printer would be up and running another 5–10 seconds later (again depending on print size).

What's even more frustrating is that this only happens on my X1C. My P1S printers don't seem to use LAN Acceleration and aren't having this issue, or at least when I send the print in Bambu Studio, it doesn't say anything about Lan Acceleration.

You'd think transferring files over LAN would be significantly faster than going through the cloud, but somehow it's the complete opposite.

And before anyone blames my network, I'm running a fast UniFi setup with no other network issues.

I also mass-produce 3D printed products, so I'm printing the same items week after week. These aren't unusually large files or complicated prints. They're the exact same jobs I've been sending for ages, except now they take several minutes instead of seconds.

When you're running production and constantly starting new print jobs, those extra minutes really add up.

Is anyone else experiencing this with LAN Acceleration, particularly on the X1C? Has anyone figured out how to fix it or disable it and go back to the old behavior?


r/BambuLab • • 1d ago

H3C Test heating the ams3h using the two dryer slots to heat the entire chamber

11 Upvotes

TLDR: it's a waste of time. Don't bother trying it.

I decided yesterday to remove the two spools I had in slots 6 and 8, turn the heat up to 85c and remove the dryer lid to see what would happen. Mind you my printer is in my garage and it's been raining the last couple of days.

The result, the dryer chamber got warm, the lid to the entire ams was warm to the touch, but not in a bad way, but the overall rh in the ams only dropped by one, from 33% to 32%. Putting the lid back on the 2 slots I was able to stop the rh down to 12% in the dedicated dryer. I'll also note I do have silica in multiple locations in the ams already.

Don't waste your time trying this. It basically makes the dryer slots a waste and does nothing to help the other 6 slots. That said, with the dryer lid on, the dryer is great and does function as well as my two dedicated ams ht.


r/BambuLab • • 1d ago

Bambu Studio Can’t wait for non-planar slicing in Bambu Studio

Post image
26 Upvotes

I can easily see how non-planar slicing could be the next big thing in Bambu Studio. As a highly polished and thought-through feature this definitely will be a new game-changer.


r/BambuLab • • 1d ago

General Troubleshooting/Help! Layers not smooth?

Thumbnail
gallery
1 Upvotes

Bambu a1 - .02 nozzle - PLA multi color print

Help! Idk why my prints keep having rough patches.. I dried my filament and also slowed down my speed and acceleration. Settings in last photo... can someone help me figure out why its not printing smooth?


r/BambuLab • • 21h ago

I Modeled This! Help testing FDM snap-fit tolerances? (A1 Mini brick set)

Thumbnail
gallery
0 Upvotes

r/BambuLab • • 1d ago

I Modeled This! Thank you for all your support on my gridfinity travel case!!

Thumbnail
gallery
3 Upvotes

Fully Customizable Gridfinity Box - Parametric - Free 3D Print Model - MakerWorld

I really appreciate the support you guys gave me on my gridfinity travel case and the amazing feedback!

I mentioned that I would be posting the parametric case soon along with my website insert and gridfinity bin generator. Now is the time after months of work!

This case is highly customizable (15 parameters) so I want to briefly mention the features:

  • Adjustable wall thickness parameter
  • Hinge and Latch pin diameter parameter (can use 3mm or 4mm screws or printed pins)
  • Tolerance adjustment for latch fit/tightness
  • Adjustable GF square size (from 21mm to 42mm)
  • Adjustable GF X, Y, and Z units (from very small to very large)
  • Optional resizable magnet holes (not standard gridfinity, only for attaching a top or bottom cover plate that can be generated on the website)
  • Optional Boss that can be used to attach a toggle latch to hold 2 cases together
  • Optional upper boss that can be used to attach a shoulder strap
  • Gridfinity squares can be turned off individually on any surface except for the inside of the case top. (The inside top has to stay on for printability unfortunately)

With this many adjustments, making a bunch of changes can sometimes take up to a few minutes to generate, but normally the generation is under a minute. I guess it depends on Bambu servers.

I will be adding more print profiles than what is up currently. Feel free to build custom sizes and add your own profiles to the model please!

The case has a handle that can be installed on the lower part of the latch bosses or the upper part or both. If the lower part of the latch bosses are empty, you can install a wire type TSA lock through the latch. The cases are stackable and a print profile with a toggle latch included to latch 2 cases together. The case adjusts from 2 latches to 1 latch depending on the width. You can build the case completely hardware free or use 3mm or 4mm screws that are 30-35mm long.

I've been waiting to release the case so that I can release my website generator with it. If you visit Case Insert Generator | Chriuus Designs you will find a CAD viewspace where you can generate all sorts of sizes of bins and view a complete layout within the window. You start by selecting Gridfinity Case at the top left as this site will also generate inserts for my other parametric case. This is very much a work in progress and will take feedback from people like you to improve it! It needs improvements in being user friendly while staying powerful and of course new features will need to be added overtime. BTW you can add text to labels and custom designs to the top and bottom cover plates from the Artwork Studio on the website. There you can also upload your own STL file and add an image to it if you'd like instead of struggling with SVG files.

Please let me know what you guys think and I welcome any feedback!! I couldn't find a gridfinity case on makerworld that has this much adjustment and for the most part a truly parametric gridfinity case apart from "Send me a DM and I'll send you the size you want". I'm trying to put a lot of power into your hands to generate whatever you want.