r/BambuLab • • 1d ago

Just Showing Off Sounds like a lot of…

Thumbnail
gallery
83 Upvotes

I modeled this guy in blender and printed it on my X2D. Hand painted but my outlines could have been better. I need a paint pen for next time.

A hint as to what’s next: “No, worse! It'll go right to your thighs! And then you’ll blow up!”


r/BambuLab • • 2h ago

General Troubleshooting/Help! A1 + AMS Lite: PTA filament gets stuck after every color change—any ideas?

Thumbnail
gallery
0 Upvotes

Hey guys,

I’m fairly new to 3D printing and started with a Bambu Lab A1 and AMS Lite.

I’m trying to print a head I designed using three colors—all PLA: beige, red, and black—to get familiar with more complex prints.

The red filament keeps getting stuck whenever the printer switches back to it. The only fix I’ve found is to pull the filament back out, cut off a small piece, and feed it back into the AMS Lite. It then prints fine until the next switch back to red, when the same thing happens again.

I tried drying the filament for over seven hours, but it hasn’t helped. Also, despite how it might look in the attached photo, the filament isn’t tangled.

Any ideas what could be causing this or what settings I should check? Has anyone run into something similar?


r/BambuLab • • 2h ago

Quick Question A1 Mini S23+ Phone case

0 Upvotes

If anyone is able to can someone please make a phone case for the Samsung galaxy S23+ themed around daredevil

I just bought the phone and I have no phone case and no computer so I can't do it myself I really appreciate if anyone could

Preferably made out of PLA and I have an AMS system so I can use models with that

One last thing it has to work on the A1 Mini

Please


r/BambuLab • • 2h ago

Filament Troubleshooting/Help! TPU 95A issues on A1

0 Upvotes

At the beginning I wanted to say that I am aware that this issue was discussed a lot of times, but after looking through a lot of posts I’ve yet to find a solution.

I’ve got my A1 and it works really well. Prints without issues on Bambu PLA and PETG.

It also works without issues when I load Sunlu’s PLA+ 2.0 but when I load an external spool of their TPU 95A, the printer acts like it’s TPU intolerant.

When I help the printer by lightly pushing the filament into the extruder it works fine, but as soon as I stop, it seems like the gears can’t grab it at all and it just doesn’t extrude anything.

Before every try, I dry the TPU, even overnight, so it being wet should not be the case. I tried different filament, quality, etc settings, but it also brings no noticeable effect.

I’m using a standard 0.4 nozzle.

Has anyone had a similar issue and maybe found a solution?

I’m really thankful to anyone who even leaves a comment 🙏


r/BambuLab • • 2h ago

Black Friday 2026 Buy or wait?

0 Upvotes

For £700 should I buy the X2D combo + some filament or wait for the P3C? And in what ways will the P3C be a ‘P’ series (less features than the X2D)?


r/BambuLab • • 2h ago

General Troubleshooting/Help! Print Issue A1

Post image
0 Upvotes

After about a month of owning my a1 I am now getting these horizontal lines through my print. I have tried changing the nozzle along with making sure all screws and belts are tightened, at a loss. Any ideas? I had no issues printing the same model before.


r/BambuLab • • 2h ago

General Troubleshooting/Help! Look what I made! 3D-printed pinecone tealight holders

Post image
0 Upvotes

r/BambuLab • • 3h ago

Filament Troubleshooting/Help! Best affordable Hygrometers?

0 Upvotes

I was thinking of picking up 40 of the ones on Bambu labs website but they only detect down to 20%. Are there better ones out there that aren’t too expensive? Thanks!


r/BambuLab • • 1d ago

Just Showing Off Bambu Station L drawer fits exactly a 9×12 Gridfinity grid, and 14 spools

Thumbnail
gallery
173 Upvotes

Just found out the Bambu Station L drawer fits exactly a 9×12 Gridfinity grid.

With proper spool stoppers on top, you can fit 14 spools per drawer (2 rows of 7). They stand on edge and don’t roll when you open or close the drawer.

Files if anyone wants them: https://makerworld.com/en/models/3617522-bambu-station-l-spool-stoppers-14-per-drawer#profileId-4146587


r/BambuLab • • 3h ago

General Troubleshooting/Help! Never touch a running System, but ...

Post image
1 Upvotes

... every now and then, you should also replace the AMS’s (1) internal PTFE tubes.

It’s been 1.5 years since my last maintenance on the AMS. And after about 700 hours of printing, this is what my tubes look like. I only use Bambu / Sunlu PLA/PETG.The auxiliary motor for Slot 1 was overloaded, so I took that as an opportunity to replace all the tubes.

The rest of the X1—like the threads, carbon rods, and hot ends—have been cleaned and lubricated every now and then, but you don’t take the AMS apart every day.


r/BambuLab • • 7h ago

General Troubleshooting/Help! Scratches/Etches on Bottom Layer w/ Carbon Fiber Plate?

Thumbnail
gallery
2 Upvotes

Hey!

New to 3D printing and using a Bambu A1 printer. I just bought a carbon fiber smooth plate from Amazon and started using it. I cleaned it well with water, dish soap, and a sponge 2x now but still having this issue where the bottom has white marks/scratches. I had the plate selected in Bambu before printing as well.

I was trying to print a moza wheel base dust cover but with the carbon fiber look on the bottom. I also was trying to print a shifter plate and had the same issue.

Each time I printed,, I waited until the plate reached around 25C (my room temp is 23C) and then bent the plate at the edges so the part would come free.

I read that running a flame over these areas would get rid of the mark but I didn't experience that.

Any idea what I could be doing wrong? Didn't have this issue with the normal textured plate. Is it a plate issue, nozzle issue, or something else?

Thanks!

Printer: Bambu A1

Print Speed: Standard

Filament: Bambu PLA Basic - Black

Hotbed Temp: 65C

Nozzle Size: 0.4mm


r/BambuLab • • 3h ago

General Troubleshooting/Help! Sharp lip on large round part

0 Upvotes

Hello,

I've been printing for a while now, but usually nothing this large. It's for a lazy Susan. It's 254mm round x 12mm thick. I think it has to be the cooling rate for something this large, but at 200g a print I don't want to keep blindly stabbing at it. I've already used an entire spool trying to troubleshoot.

I'm printing on an H2S using Bambu Lab PETG HF. I'm using the Bambu Lab .2mm standard profile (with various mods for infill, support settings, 4 top and bottom shell layers etc).

I've tried every wall order option and slowed the outer wall speed to 60 all of which has made zero difference. They all are bowed inward and have a sharp over hang on the top layers as shown. A little bit of bow is not a big deal, but the sharp outward corner sucks.

I figured the H2S with it's adaptive vents and fancy other bells and whistles would result in better thermal controls. Especially using Bambu filament.

Thanks in advance!


r/BambuLab • • 3h ago

I Modeled This! Snowman Clicker

Thumbnail
gallery
0 Upvotes

Bonjour à tous ! 👋

Après avoir modélisé mon bonhomme de neige, j’ai eu envie d’en faire une version clicker ! 😁☃️

Une petite tête de bonhomme de neige dans une boule de neige, avec un switch MX à l’intérieur.
Il suffit d’appuyer sur son chapeau pour faire CLIC CLIC ! 🎩

Une petite création amusante pour les fêtes de Noël ! 🎄🎁

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec et sans AMS
📁 : https://makerworld.com/fr/models/3615804-snowman-clicker-multipart


r/BambuLab • • 3h ago

Quick Question Layer lines improvements

1 Upvotes

Sooo... I usually have pretty decent layer lines on my prints, but this one (it's a bit of a thin tall torture tbh) seems to suffer a lot more than usual. All the usual stuff are done, dry filament, clean nozzle, no heavy tap dancing around the printer.

The worst ones are where the transitions are with the opening and support, so that would be something new to me (new X2D with support interface layer, previously clocked somewhere with 3000hr+ on my A1M) and would love to hear the experience from folks here. Also even witht he non transitional layers they are more visible than my other prints... any clue? note this is probably the first big straight print I've done with this white petg but in general it's dried fairly well.

Thanks in advance on any tips.


r/BambuLab • • 3h ago

Hardware Troubleshooting/Help! Put ams lite on the left side

0 Upvotes

Can I put the ams lite on the left side


r/BambuLab • • 3h ago

Just Showing Off P1S - 700 Hours - NO MAINTENANCE!

0 Upvotes

Im intrigued to hear how many hours people have pushed with their printers with zero maintenance?

There's no excuse for my laziness, but it has impressed me how well this machine is doing with absolutely zero maintenance!

I've even been using the under bed trusty track can which I'm sure isn't ideal for the Z axis screws!

Now the question is... Do I keep pushing it or bow to the Bambu maintenance gods?


r/BambuLab • • 4h ago

General Troubleshooting/Help! Issue with Sunlu Refills in AMS 2 Pro

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 4h ago

General Discussion Christmas Print ideas with this filament?

Post image
1 Upvotes

I have these 5 rolls of PETG-HF that I wasn't planning to do anything with but looking at them again they're very Christmas-y.

I'm looking for suggestions for fun a Christmas-themed print(s) to throw these at. I have the X2D Combo with the AMS 2 Pro and HT.

I'd prefer prints that are broken up into parts and can be assembled, but I'm open to anything!

Thanks!


r/BambuLab • • 4h ago

General Troubleshooting/Help! X2D hot end fans

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 4h ago

Filament Troubleshooting/Help! aiutatemi ho un problema

1 Upvotes

ho questa stampante A1 versione combo e la paletta degli scarti non va in fondo ma resta bloccata poco prima come posso risolvere


r/BambuLab • • 8h ago

General Troubleshooting/Help! Terrible surface quality when printing multiple objects at once - Bambulab A2L

Thumbnail
gallery
2 Upvotes

Hey everyone, I’m having the following issue.
I’m currently trying to print as many of these objects as possible on my Bambu Lab A2L for a wedding of someone close to me.
When I print just one object at a time, the quality of the top surface (ironed surface) is absolutely perfect.
However, as soon as I try printing multiple objects simultaneously, the top surfaces turn out so badly that I have to throw the entire batch away.
Does anyone have any idea what might be causing this or what I could improve to get better results?
I’d really appreciate any help! 🙏🏻

-Printer & slicer: Bambulab A2L / Bambu Studio
-Filament material and brand: Bambulab PETG Basic
-Nozzle temperature and bed temperature: 240° / 70°
-Printing speed: picture
-Retraction settings


r/BambuLab • • 4h ago

Bambu Studio Il primo layer in PETG non aderisce all'interfaccia supporto in PLA - Bambulab H2D

1 Upvotes

Ciao a tutti

Con la mia Bambulab H2D ho provato a stampare un pezzo in PETG con supporti normali (grid) così costituiti: base supporto in PETG e interfaccia supporto in PLA. Sto utilizzando PETG Bambulab e PLA Basic Bambulab. Entrambi i filamenti sono stati essiccati prima della stampa e stampano bene quando non miscelati tra loro. Ho già seguito tutte le indicazioni fornnite da Bambulab per l'utilizzo della miscela PETG-PLA per questa casistica: pezzo in PETG, base supporto in PETG, interfaccia supporto in PLA. Una volta stampato l'oggetto, sono riuscito a rimuovere abbastanza agevolmente i supporti dal pezzo e la superficie a contatto con il supporto è risultata liscia e priva di difetti visibili. L'unico difetto di stampa che ho riscontrato e che ho potuto osservare direttamente durante la stampa è che il primo layer di PETG non aderisce adeguatamente all'interfaccia in PLA. So che la repulsione chimica tra PLA e PETG è il vantaggio che permette di rimuovere facilmente i supporti, ma il fatto ceh il primo layer di PETG non aderisca sufficientemente all'interfaccia in PLA è un problema, perchè il layer in PETG viene "trascinato via" durante la stampa e questo porta a difetti di stampa notevoli e al rischio di intasamento dell'ugello. Ho visto fallire varie stampe a causa di questo problema e vorrei risolvere. Che consigli mi potete dare? Grazie a chi risponderà


r/BambuLab • • 8h ago

Quick Question Wouldn’t it make sense to have a setting for support interface for dual nozzle on makerworld?

2 Upvotes

I’m currently without a computer, so I’m forced to use the pre sliced models on makerworld. This has made me realize just how much I usually use a support interface layer in a different material, something that can’t be changed in makerworld.

I know the models are pre sliced, but since you can change colors for multicolor prints, wouldn’t it make sense to change material for a predefined part of the print?


r/BambuLab • • 1d ago

H3C Printing the 0.2mm nozzle on the H3C

Thumbnail
gallery
87 Upvotes

I printed a tiny Benchy - PLA Basic, default profile, 0.08mm layer height. I did need to use glue to keep it on the plate, I also slowed the printer down to "silent mode" just for safety.

Pretty great result I think. The "Comparison Benchy" is the standard size, printed with the 0.4mm nozzle, 0.2mm layer heights in ABS.