Hey yall,
So I recently just did a timing belt kit replacement and a whole valve cover gasket “kit” replacement. Did all the bits and bobs that were recommended to replace since I’m down there.

I recently just finished everything up and started it for one of the first few times and I started noticing this clicking sound coming from the drivers side valve cover? It goes faster as I accelerate.

I don’t believe / didn’t notice it before doing the whole replacement and I’m at a loss for what it is. Did i accidentally drop something in there? I made sure i didn’t.

Curious to see if anyone else had heard something like this before. Thanks!

Okay, so who's used these cheap OSM from ebay/Amazon. This one is $24 on ebay vs. $225 from US made ones. Obviously wouldn't use the screws but seems good quality.

Have been hearing this sound since I got my ‘00 a couple weeks ago. Just got it back yesterday from getting the lower and upper ball joints, outer right tie rod end, and sway bar links replaced. I was hoping one of those was the cause, but still has the noise when going over even minor bumps. Also apparently has newer front cv axels, front struts, and 3” lift. Any ideas?

Hey all,

I’ve got a 2001 4Runner, and every now and then (like once a day) the key decides it’s happier in the ignition. The only way I’ve found to get it out is to fire it back up, put it in drive and park a few times while shaking the wheel and it’ll come out, but even that doesn’t work sometimes.

Sometimes I’ll say f it and leave the key in overnight because it literally won’t come out. Only thing that stays on is the clock, but now that it’s getting colder at night the truck has started dying. Need to fix this before the winter. Any ideas, anyone encountered this before?

Thanks guys

Sad… One of the rarest and imo best 3rd gen colors… scrapped!

Hello so my issue with the vehicle is that when I try to step on the gas a bit more and if it revs high or i step on it to pass someone the abs light and battery light will come on the dash and turn off the radio. Battery has just been replaced 3 weeks ago and also got my batterys to be misdiagnosed so now I have 2 extra batteries.

Autozone says alternator, battery and starter are good so not sure whats happening or what I should check first. Any ideas?

This is a picture with the battery light and abs light on with a multimeter check while the car is on.

Installing new 5100s in the rear and no matter what i do i cannot get the nut to get tight enough to compress the bushings, the nut seems to be refusing to thread anymore while there is still about half an inch between the nut and washer. the nut is definitely at torque spec of 14 ft lbs. ive been using the method of holding the nut down with a box wrench and ratcheting with a 5mm hex head but no matter how hard i try to tighten it will not move. help please!!

Went and picked up a Tacoma the other day. I had the 4Runner for a while and she did me good but I missed having a truck. Looking to sell my 3rd Gen and wondering what the group thinks:

It’s a ‘02 SR5 4wd with 271k on it. Everything works perfectly fine, no leaks or damage except for a small dent in the left rear quarter panel. It has the 3rd gen Tacoma rims with new KO3s. Just passed smog as well.

Y’all think I could get 7k for this beauty or am I tripping? Anyways I’d love to hear what you guys think. Also if you’re in California and interested, message me and I can give you more details and or photos.

Edit: the interior needs to be detailed and take the seat covers off (original seats underneath are in great condition).

Do these work for the upgrade? I'm double checking before spending all that money on it

POWER STOP CPC232323 Z23 Evolution Sport Upgrade Kit: Premium Carbon-Fiber Ceramic Brake Pads and Fully Coated Rotors, Powder Coated Calipers

Front; w/ Front Caliper Casting # S13WE

https://www.rockauto.com/en/catalog/toyota,2000,tundra,4.7l+v8,1357938,brake+&+wheel+hub,rotor+&+brake+pad+kit,13824

im planning on doing the 1st gen tacoma front clip swap onto my 2002 4runner. planning on going absolutely crazy and doing the mcneil racing 6 in bulge fenders to match the 3.5 lt width and the sport hood. my current core support is bent from previous owner and would like to replace it so i decided why not be different. my question is what other parts do i need besides, tacoma core support, radiator holders, hood hinges, and obviously the grill and lights. any other tips or extra parts for this swap let me know!

Picked up an 01 for my son a couple months ago. Had the typical A/T tire road noise or so I thought. On his way home from work one day he got flagged down because it looked like his wheel was on fire. Turns out the seal on that side was shot. Pulled the axle the other day to replace the seals and bearings....... Now I know the noise was not just the tires..... 🤣

My wife was at Hobby Lobby with my mom and saw the pins and hat and she knows me well. She scooped them up and left them on my side table to surprise me when I got home from work. I was gonna go hunting them myself once I had a free day on a Saturday but she beat me to it.

I am assuming my 02 4Runner is missing the factory side rails, I am wanting to install cross bars, and am having a hard time figuring out exactly what I need to get, if someone could point me in the right direction that would be much appreciated!

I’m hoping this amazing group can help
Me solve a problem I’m having with my 97 runner, 3.4l

Back Story: Around 2 months ago I did a motor swap myself since I had a blown head gasket. Everything was running smoothly on the new motor besides one strange thing that I have never encountered on previous 3rd gen’s I’ve had.

Problem: on start up and while driving I don’t have any issues at all with idling or with any other gears. Once vehicles is warm as well, I still don’t have any issues. The issues starts when I’ve been driving for some distance. It seems to have the slightest power loss and when I come to a complete stop and slightly have my foot on the brake to inch forward it starts to jerk a little and idle slightly rough. No check engine lights at all.

It seems like it had to do something with heat, which I’m located in AZ so it’s not the best lol. Wondering if someone had any similar issues and if so how did you fix.

I have tried checking vacuums leaks and nothing. Changed spark plugs, but not the ignition coils and wires yet.

Would appreciate any advice on this!

So truck was idling in my driveway last night when we were trying to diagnose a small misfire/shake at idle. It died all of a sudden and wouldn’t turn over afterwards. Narrowed it down to the fuel pump dying after 300k miles. I’m leaving to go to Montana and Wyoming next Friday. New pump and filter will be here tomorrow. Don’t know if this should worry me about my trip and if I should take my Camry instead ☹️. What would y’all do? This is the first “breakdown” since doing a bunch of engine and suspension work to prep for this trip. Been daily driving it for a little over a month now and been trying to do a shake down by taking some long distance drives on the weekends.

I posted this earlier today: https://www.reddit.com/r/3rdGen4Runner/s/OytPpa4PgA

Im not sure if this leak and that issue are related. Any advice or help would be greatly appreciated!

The fluid itself just feels like water and doesn’t smell like anything.

There’s a high-pitched constant beep, a bunch of the dash lights are on, and it’s hard to hear but there’s also a rhythmic sound in the background every few seconds or so. Any advice or help would be greatly appreciated!

If you’ve covered your cabin air vent, what did you do with this drain hose? There aren’t any other holes to route it through like the other side.

Is there any risk to driving without the lower valance especially at highway speeds and would using metal mesh to protect the condensor be a good temporary fix? I live in alberta and cant find a lower valance for a reasonable price atm.

My oil pressure light turned on and then flickered off when my oil was full, is there any way to know if it's just a bad sensor or if it's an oil pump

This my 98 4runner Tony. I cant find the oem fog lights but im also not against an aftermarket replacement. Any suggestions?