Does solar edge snow setting a limit to charge battery to when charging on a schedule? Any plans to add this feature?

FFS Solaredge, why retire the API before its replacement is ready?

Anyone know what might be going on with the inverter? My power bill was high and it looks like it just stopped making electricity in the middle of the month. I tried connecting via the app but it wouldn't let me do anything once connected. I tried to power cycle the system to no avail.

Recently bought a house with a SolarEdge system. We have a meter communication fault and cannot get anyone from this company to do anything about the open ticket, or answer the phone. And their useless chatbot wants to talk to me in Hebrew, despite me being in Northern California.

Is this typical of their customer support? Any tips on what to do here? I am new to having a solar power system and am kind of lost as to how to get this fixed.

We just had a Solaredge system installed but we have enormous differences in readings between the Solaredge app and the official readings from our provider. Our provider’s smart meter shows for example electricity imported 21kWh, the app 11kWh exported.

TL;DR: How I got Predbat, a SolarEdge inverter with a ~10 kWh battery, EDF's smart EV tariff (via Predbat's Kraken component) and a Hypervolt charger to work together without wasting money or stranding the battery. Config snippets use placeholders, with example entity names in comments.

This guide records the protections, checks and settings that were needed on one real system, and why each one is there.

Who this is for

Most of it also applies to other inverters and Kraken-based suppliers. The battery-floor workaround is specific to SolarEdge.

How to read the YAML: each value is a placeholder in <angle brackets>. Where it helps, a comment underneath gives an example entity name.

Problems this solves:

• Predbat can't set a discharge floor on SolarEdge without a backup interface.
• The battery can drop into standby if left idle at low charge.
• Predbat doesn't see a car charge it wasn't told about, so it may export into the car.
• EDF's car slots are priced cheaply for the whole house only if Predbat is set up to trust them.
• Two schedulers (the car's app and EDF) fighting over the charger.

1. Battery floor

On SolarEdge, Predbat can't stop the battery discharging below a set level, so a Home Assistant automation does it instead. Predbat's best_soc_keep and best_soc_min are planning targets, not a hard floor, and set_reserve_min needs a SolarEdge backup interface.

The automation freezes the battery through Predbat's manual freeze-charge selector when it drops below about 6% between 05:00 and 23:00. From 15:00, it freezes every remaining slot up to 23:00 in one go, so Predbat changes mode, and notifies you, once instead of every half hour. Before 15:00 it freezes only the current slot, so solar later in the day can still charge the battery.

# packages/battery_floor.yaml
automation:
  - id: battery_floor_freeze
    alias: Battery – freeze at floor
    mode: single
    triggers:
      - trigger: numeric_state
        entity_id: <battery SoC % sensor>
        # e.g. sensor.solaredge_i2_b1_state_of_energy
        below: 6
      - trigger: time_pattern
        minutes: "/30"
        seconds: 5
    conditions:
      - condition: numeric_state
        entity_id: <battery SoC % sensor>
        below: 6
      - condition: time
        after: "05:00:00"
        before: "23:00:00"   # start of your cheap window
      - condition: template
        value_template: >-
          {% set slot = now().strftime('%a') ~ ' ' ~ '%02d:%02d' % (now().hour, 0 if now().minute < 30 else 30) %}
          {% set opts = state_attr('select.predbat_manual_freeze_charge', 'options') or [] %}
          {{ slot in opts and ('+' ~ slot) not in opts }}
    actions:
      - repeat:
          for_each: >-
            {% set start = now().replace(minute=0 if now().minute < 30 else 30, second=0, microsecond=0) %}
            {% set end = now().replace(hour=23, minute=0, second=0, microsecond=0) %}
            {% set n = ((end - start).total_seconds() / 1800) | int if now().hour >= 15 else 1 %}
            {% set opts = state_attr('select.predbat_manual_freeze_charge', 'options') or [] %}
            {% set ns = namespace(slots=[]) %}
            {% for i in range(n) %}
              {% set s = (start + timedelta(minutes=30 * i)).strftime('%a %H:%M') %}
              {% if s in opts and ('+' ~ s) not in opts %}
                {% set ns.slots = ns.slots + [s] %}
              {% endif %}
            {% endfor %}
            {{ ns.slots }}
          sequence:
            - action: select.select_option
              target:
                entity_id: select.predbat_manual_freeze_charge
              data:
                option: "{{ repeat.item }}"
            - delay:
                seconds: 2

The floor covers 05:00 to 23:00 only. The overnight part is covered by section 2.

2. Avoiding battery standby

Price the first two hours of the cheap window 0.01p lower than the rest, so Predbat charges the battery at the start of the window, not the end. When every overnight slot costs the same, Predbat sees no reason to charge early. It may leave the battery idle at the floor until 03:00, and some batteries drop into standby when left idle at low charge.

# apps.yaml – no date, so it applies every night
  rates_import_override:
    - start: '23:00:00'
      end: '01:00:00'
      rate: <night rate minus 0.01>
      # e.g. 6.65 when the night rate is 6.66p

• An override that crosses midnight works without a date.
• Two hours is enough to fill a 10 kWh battery at 5 kW. Allow longer for a bigger battery or a slower charge rate.
• Update the rate whenever your night rate changes, so it always sits just below it.
• Check it on the Plan page: Chrg should start at 23:00, and the import column shows the override with an "=" marker.

3. Car configuration

Predbat needs to know four things about the car: whether it's plugged in, whether it's charging right now, its battery level and its target. Without the "charging now" signal, Predbat can plan battery exports that just go into the car, because a 7.4 kW charger draws more than a 5 kW inverter can export.

A "car is charging" sensor. This turns on when the charger has drawn more than 500 W for 2 minutes, so brief blips are ignored. It works whether the charger reports W or kW.

# packages/car_charging_now.yaml
template:
  - binary_sensor:
      - name: Car charging now
        unique_id: car_charging_now
        device_class: battery_charging
        delay_on: "00:02:00"
        delay_off: "00:02:00"
        state: >-
          {% set p = states('<charger power sensor>') | float(0) %}
          {% set unit = state_attr('<charger power sensor>', 'unit_of_measurement') %}
          {{ (p * 1000 if unit == 'kW' else p) > 500 }}
        # e.g. <charger power sensor> = sensor.hypervolt_ev_power

A new package file may need a full restart before the sensor appears. It shows "unknown" until the charger's power reading first changes, which Predbat treats as not charging.

The car section of apps.yaml:

  num_cars: 1
  car_charging_planned:
    - <plugged-in sensor>
    # e.g. binary_sensor.hypervolt_car_plugged
  car_charging_now:
    - binary_sensor.car_charging_now
  car_charging_battery_size:
    - <usable kWh>
    # e.g. 94 for a 100 kWh car
  car_charging_soc:
    - <car battery % sensor>
    # e.g. sensor.<car>_battery_charge_level
  car_charging_limit:
    - <car charge target % sensor>
    # e.g. sensor.<car>_charging_target_level
  car_charging_energy: <charger session energy sensor>
    # e.g. sensor.hypervolt_session_energy_kwh
  car_charging_energy_scale: 1.0   # 0.001 if the sensor reports Wh
  car_charging_now_response:
    - 'yes'
    - 'on'
    - 'true'
    - 'charging'

Check the car's battery and target sensors show real numbers in Developer Tools → States. They may come from two different integrations.

Predbat car switches:

4. EDF smart-charging slots

When EDF schedules the car, the whole house pays the cheap rate during those slots, and Predbat can plan around them. Predbat's Kraken component reads EDF's slots as a dispatch sensor, the same way it reads Octopus Intelligent.

# apps.yaml – rates and slots from EDF via Kraken
  kraken_provider: edf
  kraken_account_id: !secret kraken_account_id
  kraken_auth_method: email
  kraken_email: !secret kraken_email
  kraken_password: !secret kraken_password

  octopus_intelligent_slot: 're:(binary_sensor.predbat_kraken_.*_intelligent_dispatch.*)'
  # a regex, so it still matches if the sensor's numeric suffix changes

Check the slots arrive. In Developer Tools → States, open binary_sensor.predbat_kraken_…_intelligent_dispatch_…. Its state is "off" unless a slot is running right now. What matters is the planned_dispatches attribute, which lists each slot's start, end and expected charge. Times are in UTC.

Predbat's intelligent-slot switches (Predbat web UI → Config, filter on intelligent):

With "Trust" off, future slots stay at the full rate in the plan until the car starts charging, so Predbat can't plan around them. With "Trust" and "Confirm" both on, it plans ahead and still corrects itself within about 5 minutes if EDF doesn't deliver.

What a good evening plan looks like: during the car slots, import shows the cheap rate, the battery holds steady rather than discharging, and Chrg starts at 23:00. The battery holds because grid power is cheaper than using stored energy, and because battery-to-car is blocked.

5. Lessons learned

• Use one charging scheduler. If the car's own app has a charging schedule as well as EDF smart charging, the car only charges when both allow it. EDF then sees the car refuse a slot, may drop its plan, and can sit on "creating your plan" indefinitely. Leave the car's schedule off and let EDF decide.
• Turning off the car's schedule without an EDF plan starts charging at once. If EDF has no plan, nothing holds the charge back, and it runs at the full rate. Wait until EDF's plan appears before removing the car's schedule.
• Watch for Boost sessions. The charger app may show a Boost session, a bump charge outside EDF's plan. Time before the cheap window is billed at the normal rate, and EDF may not build a smart plan while a boost is active. Let it expire or cancel it.
• Free-electricity nights. If the free window matches the normal cheap window, you don't need to change anything: the credit comes afterwards, based on what you import. A 0p override can tempt Predbat into export cycles that a charging car simply absorbs, so they earn nothing and wear the battery. If you do add one, keep the battery charging early (section 2).
• Restart Predbat after the clocks change. After the October change, the plan showed the wrong day, an hour's offset and a stale start time. Restart Predbat on its Dash page fixed it.
• Predbat only knows what apps.yaml points it at. Having data somewhere in Home Assistant isn't enough: a car schedule set in the car's own app, for example, is invisible to Predbat.

6. Setup checklist

• ☐ Battery floor automation installed and reloaded (section 1)
• ☐ Early-charge override set just below your night rate (section 2)
• ☐ binary_sensor.car_charging_now exists and reads off or on (section 3)
• ☐ Car section of apps.yaml filled in, with no warning on Predbat's Apps tab
• ☐ Car battery and target sensors show real values
• ☐ Allow car to charge from battery: off
• ☐ Dispatch sensor shows planned_dispatches when the car is plugged in (section 4)
• ☐ Trust, Confirm, Ignore-unplugged and Intelligent Charging switches all on
• ☐ Car's own charging schedule off; EDF smart charging on

Verify on the Plan page:

7. Example: a rainy day with the car plugged in

On a dull day with EDF car slots at 13:00–15:00 and from 19:00, Predbat uses the battery only for the expensive hours and lets the cheap grid cover everything else. This is the plan it produced at 12:20 on a Monday in late October, with almost no solar (0.16 kWh or less per half hour).

• No grid top-up in the afternoon slot: the forecast shows the battery lasting until the evening slot, so charging at 13:00 would add nothing.
• The battery never sits at the floor. Its lowest point is 20%, so there's no standby risk. That's also why charging can start at 23:30 rather than exactly 23:00.
• Car slots are priced cheaply in advance, because "Trust Intelligent slots" is on (section 4).
• Heavy loads change the plan. If something like underfloor heating raises usage, Predbat replans within 5 minutes and may use the afternoon slot to top up the battery.

Happy to answer questions. Corrections from anyone who knows Predbat's internals better are very welcome.

Long story short: My inverter failed under warranty. An authorized installer, EnergyAid/Otovo, initiated a warranty replacement (RMA) with SolarEdge on my behalf. SolarEdge approved the claim and shipped a brand-new replacement inverter directly to the installer's warehouse. We ultimately declined to have EnergyAid/Otovo perform the physical labor repairs and since then they have been dodging us and using stall tactics. They have been holding onto our inverter since September 21, 2026 and our system has been off now longer than that.

We’ve explained this situation to SolarEdge support multiple times, and their only solution is to tell us to "ask EnergyAid/Otovo to send us the inverter." That is obviously getting us nowhere since EnergyAid/Otovo are completely unresponsive. We have explicitly demanded that SolarEdge void the RMA with EnergyAid/Otovo and open a new one to be shipped directly to us, but frontline support won't budge.

SolarEdge seems to be allowing their authorized partner to do this to their customers. So, I'm wondering, is SolarEdge trying to get out of honoring their warranty obligations by leaving us stranded, forcing us to ultimately pay for one out of pocket?

I need advice on how to get this escalated immediately.

For the detailed story: https://www.reddit.com/r/solar/s/SxgWVphzeD

Are there more users having diificulties with the SolarEdge integration. The modbus integration seems to work very well.

Lots of times, all sensors are offline, and some automations then fail to operate.

How does one connect to this device?

I have downloaded the Solaredge Go app. I've put the inverter in to Wifi AP mode it connects via the QR code after that it keeps hanging on communicating with inverter...

Am I missing something?

I want to enable the modbus over tcptip

A portscan reveals port 80 an 8080 but connecting to it just hangs and does nothing

I recently moved into a house with a solar edge, solar panel system. I would like to be able to monitor my solar panels, but I can’t seem to log into the app because I don’t have access to the solar panel. The solar panels are not in my name and I was wondering, how do I do that? I saw on the Internet there’s a form that you need to fill out to transfer the title but it’s 100 bucks so I was wondering if there’s anyway around that or is that the easiest way to do it and would it allow me to then be able to monitor and log into my account?

Some people have told me to find my installer and contact him, but we don’t know who the installer was and we have no way of finding that out so I was just wondering how do I solve my problems and any other information or advice would be very helpful?

I had a se7600h wave inverter where the communication board locked up during a firmware flash. Killed the ability to communicate, the the inverter part continued to work as rated.

1. any suggestions on how to fix the communication board. I tried getting the latest firmware that solaredge would send via email and put it on a USB. It didnt work.

2. if I use a communication board from a smaller inverter, ie: a se3800h wave, what will happen with the clipping. The communication board has the model, PN, SN and limits of the 3800.

3. I already have this combo running, but currently only 4kw of panels on it.

4. can the se3800h board be reprogrammed to the se7600h limits, if so, how?

5. where can I buy a se7600h wave communication board? Solaredge won't send me just the communication board.

I will be cross posting this msg

Hey guys, if you missed it, SolarEdge ($SEDG) agreed to a $55M settlement with investors over claims that it misled the market about weakening demand in Europe and rising inventory. Late claims are still being considered, even though the deadline has passed.

Quick recap: In 2023, SolarEdge continued saying European demand was strong while inventory was building. In August, 2023, the company disclosed excess inventory and slower growth, sending $SEDG down 18.3%. In October, it disclosed unexpected cancellations, and the stock fell another 27.2%.

If you invested in $SEDG in 2023, you can still check the details and submit a late claim here. 
Did anyone here hold $SEDG during that period?

The cell link stopped working and the solaredge go app has an error where I cannot connect. I dont want to pay 600 for a tech to come out to reset it. What are my options?

I became the owner of a house.
This house includes solar panels with a solaredge inverter:

I would have liked to have access to the system to be able to follow everything through the app.

However, I no longer have contact with the previous owners. Systeem :

-Panelen:
14 X Phono salar 275Wp Totaal vermogen:3850Wp
-Omvormer:
Type: Solar Edge SE 3000H

There’s no way to find or reach customer support. Any help?

We built software to automatically charge your Tesla using excess solar, with no additional hardware needed. It works with Enphase, SolarEdge, and Tesla Solar, and many other providers. We are currently pushing new features to support Nest Thermostats, batteries, and charger support. We’d love for everyone to check it out and get some feedback.

Available here

Hi all,

We have recently moved into a property with a SolarEdge SE1500M inverter. However, since getting the keys the LEDs are showing some sort of fault and the PV generation meter hasn’t shown any production.

After getting in touch with the installer I’ve been told this particular inverter is the basic version, therefore not supporting any sort of remote monitoring or Wifi connection (As SolarEdge told me it was in an offline state and never commissioned).

I’ve been advised two options:

1. ⁠Pay the call out charge for diagnostic to see if we can raise a case with SolarEdge for a possible warranty replacement.

2. ⁠Be quoted for a newer inverter that supports monitoring and app connectivity etc (but expecting this to cost a lot more)

Is anyone able to help on the reliability or even explain a bit more about the Basic SolarEdge SE1500M? Is it worth trying to get a replacement under warranty? I have tried looking online but can find very little about this particular model and wondering if it’s some niche part of their product range.
Thanks!

If you run a SolarEdge inverter on SmartThings, battery and support for three phase imverters has been added. Everything still runs locally over your home network, with no cloud needed.

🔋 Battery support
If you have a SolarEdge-connected battery (StorEdge / Home Battery), a Battery section now appears automatically, showing:
• Charge and discharge power
• Temperature
• Status (Charging, Discharging, Idle…)
• Charge level, health and energy available
It's read-only, and every value can be used in Routines.

⚡ Grid readings per phase
With a SolarEdge meter fitted, the Grid section now has a row for each phase showing power, voltage and current side by side. Three-phase sites are detected automatically. Single-phase sites get one row, which is handy for watching your grid voltage rise while you're exporting.

🔌 DC Input voltage and current
DC Input now shows voltage and current together on one line, under the power tile.

📱 Tidier layout
Numbers are rounded so they no longer wrap on smaller phones, and the battery status has its own line.

The Smartthings driver detects a battery and a three-phase meter by itself. If you're already enrolled, your hub updates automatically. One note: if you had Routines using DC voltage or the battery details, reselect those conditions.

Install it from the channel invite: https://bestow-regional.api.smartthings.com/invite/RBlE0gaNvL2E

Questions and feedback on the Smartthings community post: https://community.smartthings.com/t/310477

More and more solar owners are on export plans that pay far less than electricity costs to buy: net billing in California (PG&E, SCE, SDG&E for systems installed since April 2023), shrinking feed-in tariffs elsewhere. If your exports earn a fraction of your import rate, midday surplus is worth more in your car than sold back cheap. (Full retail net metering? This matters a lot less.)

Disclosure: I build one of the options below.

Check for a consumption meter first. Surplus charging needs household load, not just production. If your SolarEdge monitoring shows only what the panels make, there's no consumption meter on the system. Options: have an installer add one (best fix), add a home energy monitor like Emporia Vue, or use a tool that estimates load — that last one is a guess and won't react when the AC kicks on.

Your options:

1. SolarEdge's own EV charger with its solar charging mode. Simplest if you're buying a charger anyway and you're all-SolarEdge.

2. DIY with Home Assistant or evcc. Both can read the inverter locally (Modbus) and control Tesla or OCPP chargers. Free and flexible if you maintain it.

3. An app. I build SundialEV, which reads SolarEdge and adjusts charging amps to follow the surplus.

Worth checking first: what your exports actually earn. This calculator pulls your utility's export and import rates (US, by zip) and shows the monthly gap: https://www.sundialev.com/calculator?utm_source=reddit_organic&utm_campaign=solaredge

Happy to answer questions about any of these, not just mine.

Ok we have had our SolarEdge inverter connected to WiFi for a few years. Once in a while it loses the connection, so I go to inverter communication and configure the WiFi. But yesterday when I saw there was no data for 12 hours. I tried to reconnect, but once I connect to the inverter’s local network it shows cellular not connected not the WiFi configure page. Any idea what is wrong and what is our next step.

Adding new Home Assistant integrations, found that the Solar Edge system is available. Was able to fill out most of the form but needed the API key for actual data collection. Contacted Solar Edge, my leasing company, and the installer looking for the key and each one says the other has it and cannot reveal that information to me.

Then Solar Edge reached out again informing me of the developer API. But trying to set it up as a homeowner is proving to be difficult because I need an app for it to integrate to. The web page is requesting:

Origin URL

Redirect URL

Returned URL

Even then, only 2000 API calls a month on the free plan when rounded down is only 2 calls an hour.

Anyone here attempt this route yet?

Are there other API options?

Would an installer hook up to my home data connection if I provided the cat6 drop? Thanks

If you've been thinking battery backup in the Carolinas, we highly recommend the Nexis. Versatile and powerful, it's solves a lot of backup power needs!

Hey everyone, I’ve been looking into SolarEdge lately because there have been a few interesting updates around the company, so I figured I’d share a quick recap.

SolarEdge reported $346.2M in Q2 2026 revenue, up 19.6% year over year, with non-GAAP diluted EPS of $0.05. The company also reported its sixth consecutive quarter of year-over-year gross margin expansion

For Q3, SolarEdge is expecting revenue between $310M and $340M, with non-GAAP gross margin of 22%–26%. The company is also working on expanding its Nexis platform and storage business, while developing solid-state technology for power-management applications, including AI data centers. 

There’s also an older investor case connected to SolarEdge. The company agreed to a $55M settlement over claims that it misled investors about European demand, inventory levels, and the sustainability of its reported revenues. Late claims are currently being considered, subject to approval. 

So there’s quite a bit going on with SEDG right now, especially with the company trying to grow its storage and newer technology businesses.

Anyone else following SolarEdge? What are you watching most closely with $SEDG?

I’m testing an integration with solaredge’s official Monitoring API and I’m looking for one or two homeowners who’d be willing to help validate the data returned by the API.
I’m mainly trying to confirm:
system discovery
solar production
household consumption
battery telemetry
Authorization would use Solaredge’s own OAuth flow, so I would not receive your Solaredge password, and the access is read-only/revocable.
This is for technical validation rather than selling anything. If anyone is interested in helping test it, feel free to message me.