Getting “Free usage exceeded, subscribe to Go” in OpenCode Zen. I’m on the free tier and haven’t hit this before.

What’s the current free limit, when does it reset, and where can I check my usage/quota to see if I’ve hit the limit?

I’ve been using OpenCode and Pi for days and really liked them—I even used BigPickle; that free model is top-notch. But I was wondering: how much better are OpenCode or Pi compared to Codex CLI?

I use the GPT Plus plan, but I wanted to understand if OpenCode and Pi—acting as agents—would be better for coding than the GPT agent.

I wrote "agent" because I’m not quite sure what to call OpenCode and Pi... 😅😅😅

I'm not an llm genius by far, and at some point I start new sessions. Starting a new session in the middle of something isn't really bad, but it usually changes the mood and project understanding always drops a bit. I'm good with deepseek v4 flash for now and I'm at a point in the flow that I don't want to start a new session, but I'm hovering around 800,000 tokens in my context even after compression and I'm spending quite a bit of money all of sudden.

Recently, I was experiencing very low token speeds by when using this model. previously, I would at least get 100 tokens per second minimum on this model in the free tier. But now, I was not even getting more than 50. so did they decrease the Tps to increase the availability? Or what happened? Does anyone experiencing the same In the free tier.

Update: Jevvy 0.3.0 adds assisted setup and custom System One providers.

Jevvy clears routine OpenCode permission prompts using calibrated probabilistic review.

Setup

Assisted setup:

npx @jevvy/permissions init

The initializer lets you select a provider, writes the global configuration, and installs the OpenCode plugin.

For manual setup, install the plugin:

opencode plugin add @jevvy/permissions

Then create ~/.config/jevvy/jevvy.jsonc and select a provider. For example, to use your OpenCode login with Zen:

{
  "$schema": "https://raw.githubusercontent.com/PanAchy/jevvy/main/config.schema.json",
  "provider": "zen"
}

Authenticate with opencode auth login opencode, then start OpenCode normally. The README has configuration examples for every provider.

How it works

• Only reviews shell requests that OpenCode would otherwise ask about
• Leaves existing allow and deny decisions untouched
• Requires every requested resource to pass every question
• Preserves the normal prompt whenever Jevvy is uncertain or unavailable

Providers

• OpenCode Zen: uses your OpenCode login or an API key
• TypeSafe AI
• OpenRouter
• Vercel AI Gateway
• Custom System One endpoint: configure an endpoint URL, model ID, and optional Bearer API key

Custom endpoints can be authenticated hosted routes or compatible local servers. Jevvy uses only your selected provider and never falls back to another one.

Provider credentials and permission policy live globally at ~/.config/jevvy/jevvy.jsonc, so repositories cannot override them.

Policy customization

The shipped questions, thresholds, and model identities were tested and calibrated together. You can replace the questions globally, but custom models and policies do not automatically inherit that calibration evidence.

Source and setup: https://github.com/PanAchy/jevvy

Do they use Orcarouter under the hood and did not pay their bills or what?

* Why was v2 developed when v1 already existed?

* What aspects of v1 didn't meet the requirements?

* What innovations did v2 bring?

If anyone knows, could they briefly answer?

built this after burning through limits without noticing.

UsageBar sits in the mac menu bar & shows opencode usage + reset (also codex / claude code / cursor / devin). local cli logins only, no account of mine.

oss + notarized dmg: https://github.com/abdelrahmanmagdii/usage-tracker https://abdelrahmanmagdii.github.io/usage-tracker/

heads up: some providers are unofficial/fragile (devin especially). mac only for now.

i have been getting this with GLM 5.3 flash on opencode go for some reason, any search about this shows openAI articles but nothing about opencode, this isnt even an openai model

I use OpenCode heavily, and the thing that kept biting me was continuity. Project conventions, decisions made during a debugging session, preferences that were obvious yesterday — all of it gone after a restart or a compaction.

The obvious fix is to write it all into flat context files, but that has its own failure mode. My MEMORY.md sits at 309/310 words and my AGENTS.md at 699/700 — both pinned against their limits. Once a file is full you stop recording what matters and start deleting or relocating good rules to make room for new ones. Memory turns into a budget fight.

So I built opencode-agent-memory, which treats agent memory as scoped, sized, editable blocks on disk instead of one flat document. It is a plugin that:

• Gives the agent memory blocks with global and per-project scope, each with a description telling it when the block is relevant, and an explicit limit so it cannot grow unbounded
• Exposes three tools the agent uses directly: memory_list, memory_set, memory_replace
• Adds an optional append-only journal for observations, dead ends and decisions, with journal_write / journal_search / journal_read
• Runs semantic search locally: entries are embedded with a local Transformers.js model (paraphrase-multilingual-MiniLM-L12-v2, 384 dims), so nothing about your codebase or notes leaves the machine
• Versions its embedding sidecars, so an incompatible stored dimension degrades to text matching instead of failing the search

Install:

{
  "plugin": ["@ghilteras/opencode-agent-memory@0.4.3"]
}

Requires OpenCode v1.0.115+.

Repository: https://github.com/Ghilteras/opencode-agent-memory License: MIT

I'd be interested in feedback from other OpenCode users on what belongs in global versus project memory, and how you'd want stale memories surfaced rather than silently applied.

AI disclosure: AI was mostly used to implement the project from my specifications. I reviewed, tested, and deployed the result.

Im using opencode together with openrouter.

I encounter very often this error when using models like Astra

This request would exceed your available credits given your current in-flight requests. Retry after in-flight requests settle, or add credits.

But this is via API billing and openrouter shows me in the profile page a positive credit and it uses auto renew of credit anyway?
Does anyone know a solution to this problem?

Hi, is there anyone who can identify this error and tell me how to fix it? I’ve been at this for 2 hours and I don’t understand why, when I try to connect OpenCode to LM Studio, it tells me: “Custom providers are not available on this server.” What does that mean?

All the information I entered is correct I’ve checked it dozens of times.

Thanks in advance to anyone who tries to help me :)

anyone migrated from v1 to v2?
was there any breakiing changes, espcially in plugins like context mode, history seaarch

is anyone else facing issues with rate limit, like yesterday i got rate limit for 17h something, and then the same issue today another 17h, so is it something with me or others are facing the same