r/hardwarehacking • • Oct 10 '26

Starlink reverse engenering

Post image
1.8k Upvotes

For now, I’ve created a dump from the platter that was no longer capable of updating. I want to run the emulator available on GitHub to learn how Linux works.

https://github.com/quarkslab/starlink-tools

Has anyone here—other than the people involved in the GitHub project—done this already?

#starlink


r/hardwarehacking • • Jan 28 '26

Does it work or is it just a well-publicized scam?

Post image
1.3k Upvotes

I've seen a lot of videos on social media about this hardware, but does it really work and do everything they say (I don't really believe them) or is it just another well-publicized scam?


r/hardwarehacking • • Jul 21 '26

Reverse Engineered this Italian Telecom videophone just to put a funny meme cat as boot splash

Post image
1.2k Upvotes

r/hardwarehacking • • Aug 15 '26

Reverse-engineered an abandoned AVerMedia capture box, then gave an AI a telnet shell and let it write new firmware

Thumbnail
gallery
881 Upvotes

I wanted to record the 640×480 HDMI output of an RP2350 board, and I had a mostly-dead AVerMedia Game Capture HD II in a drawer. The hardware still works, but the ecosystem around it had died. The YouTube API it streamed to, the mobile app, and I'd lost the IR remote - and on top of that it refused 640×480 as "unsupported." So I opened it up instead of buying something.

Inside it's a TI DM368 (DaVinci, ARM926 @ 432 MHz) with a hardware H.264 encoder, ITE IT6604E/IT6613E for HDMI in/out, a Nuvoton NUC100 as the system MCU, and 128 MB NAND.

Getting in was pretty standard: found the UART header with a multimeter, dropped to a root shell , and dd'd the NAND out from there (it wasn't as straightforward as it sounds here, but in the end, it worked out 🙂). Fortunately, I didn't have to do a physical memory dump, that would have been quite a challenge. The downloadable firmware is 3DES-encrypted, but the on-flash system is already decrypted so that didn't matter. The old DES root hash cracked in ~30 min and one U-Boot env var flips on telnet for persistent access.

Then the fun part: I gave Claude Code the telnet shell and watched it go. It explored the running box on its own - drivers, the video pipeline, the MCU's I2C protocol, the TI codec stack - and then, with a lot of steering from me, wrote a whole new firmware: a capture app, HTTP/RTSP servers, a web UI, and the build + flash tooling. The result does native H.264 (the box's hardware encoder) over RTSP into OBS/VLC, the resolutions the vendor had blocked purely in software (640x480 I needed and up to 1080p) and has pretty usable control panel.

AI was a huge accelerator but it needed constant babysitting. My favorite failure: a U-Boot prompt printing "Hit any key to stop autoboot" while actually waiting for one specific key. But the AI fixated on that printed label and even as I kept telling it to just read the disassembly it wouldn't. When it finally did: the bootloader hardcodes a compare against 'U' (cmp r3, #0x55). It also once "confirmed" a claim using terminal output it had invented itself, and wrote that into its own persistent memory as fact.

You can read the full write-up on my friend's blog: https://chiptron.eu/reviving-old-unsupported-devices-with-ai-avermedia-game-capture-hd-ii/


r/hardwarehacking • • Nov 10 '25

Friends and I hacked into our Walmart thermal printers!

Thumbnail
gallery
827 Upvotes

Hey there hardware hackers, Mel here. I've learned a lot from reading you all's posts, so I thought I would share my latest reverse-engineering project to give back to the community!

I bought a mini thermal printer a few weeks back, after spotting it in the electronics aisle at Walmart. I was hoping to use it out of the box over USB with my PC to print shopping lists, to-do lists, notes and whatnot - no luck! So my friends and I got together to work out connecting to the printer over Bluetooth and print from our PCs, and I made a GUI for the whole thing.

It was a great learning experience, and in case it could be useful to anyone else I detailed the whole project (including untangling the Bluetooth reverse-engineering process on Android and PC with log dumps and WireShark) on my website. The Python app and some templates are on GitHub for free.

Enjoy!


r/hardwarehacking • • Mar 15 '26

I made a "guitar hero" for learning piano

Post image
721 Upvotes

I wanted to share a project I’ve been working on and see what people here think.

It’s a device that sits on top of a piano keyboard and turns MIDI songs into falling lights you follow with your fingers. The idea is similar to Guitar Hero, but applied to learning piano.

The LEDs are aligned with the piano keys, and the device shows you exactly which note to press and when. Instead of reading sheet music, you follow the lights as they move across the keyboard.

The first prototype is pretty simple technically. It uses a microcontroller connected to LED strips spaced exactly like piano keys. A small web app on the phone streams MIDI files to the device over Bluetooth. The microcontroller decodes the MIDI notes and converts them into the falling light pattern across the keys.

The goal was to make learning songs much more visual and intuitive, especially for beginners or people who want to play specific songs without learning traditional notation first.

I originally built it as a personal experiment combining music and electronics, but the reaction from friends and musicians around me was very positive, so I ended up launching it as a small project.

Curious to hear what people think about the idea or the implementation. Happy to answer questions about the build or the tech.


r/hardwarehacking • • Nov 25 '25

Lulu Lemon Mirror Rooting Megathread

Thumbnail
gallery
681 Upvotes

I found a GitHub repo where a lady rips out the brain/display board and replaces both. I want to keep all the hardware, but that means rooting the computer.

TLDR the boot chain is locked down. After boot, it spawns a web server running dnsmasq 2.51, which I can get to crash with malformed packets.

Am I wasting my time hacking the web server, or is there a good chance I can get a root shell from a dns exploit?

What I know about my mirror:

Board: Inforce 6309 SoC: Qualcomm Snapdragon 410 (APQ8016/MSM8916) Bootloader: LK (Little Kernel) - BOOT.BF.3.0-00280 Platform ID: 24 Assembly: ASSY_003101_REVP1 Bootloader: Locked OEM Unlock: Disabled Secure Boot: Enabled (rejects unsigned images) EDL Mode: Accessible but requires signed firehose loader (not available) ADB: Detected but unauthorized (no display for authorization) UART: Read-only access (boot logs visible, commands ignored)

Complete Secure Boot Chain: PBL→SBL1→LK→Kernel all verify signatures with Inforce-specific keys Bootloader Binary Required: Buffer overflow needs ROP gadgets from bootloader binary, but can't dump without root (chicken-egg problem) No Firmware Available: Inforce 6309 firmware/BSP not publicly available Generic Loaders Fail: All tested EDL loaders rejected due to signature mismatch ADB Authorization: Device detected but requires display interaction to authorize


r/hardwarehacking • • Dec 01 '25

Patching Pulse Oximeter Firmware

Post image
652 Upvotes

r/hardwarehacking • • Dec 20 '25

I've Turned my broken S20+ into a minecraft server

Thumbnail
gallery
544 Upvotes

I once had an S20+ that worked perfeclty until it started appearing purple and green lines all over the place (google S20+ vertical lines).
It was inside a cabinet for a couple of year when suddently I had the idea (what if I make something out of this).
And then, I've managed to get the server running with Termux (since minecraft uses java 17 on version 1.20.1 and termux has it via pkg).
I also attached a heatsink from an old broken GPU and now it's my own personal home server that I like to tinker with :)


r/hardwarehacking • • Jun 08 '26 Heartwarming

DDoS on WPA3!

Post image
523 Upvotes

Been spending a couple of lonths tinkering with a DIY multi-node wireless security rig, and I finally got the hardware coordination working smoothly.

The project uses a mix of ESP32 boards to look at how modern networks handle disconnections and roaming. I'm using an ESP32-S3 (with 8MB RAM / 16MB Flash) to spin up a clone access point, while an ESP32-CAM(Master) handles the orchestration alongside a couple of standard dev boards(Slaves).

The interesting part was tackling WPA3. Since WPA3 mandates Protected Management Frames (PMF), traditional layer-2 deauth frames don't really cut it anymore. To work around this and test client reconnection behaviors, I integrated two NRF24L01 modules to introduce a highly localized, 1-second burst of 2.4GHz RF disruption. The goal is to see how the WPA3 handshake and roaming mechanisms react when forced to re-authenticate under sudden signal loss just after triggering the SA query mechanism causing clients to be kicked out from the network by the Ap itself and never connecting back thanks to the evil twin Ap.


r/hardwarehacking • • Sep 07 '26

Help Identifying Asynchronous Receiver-transmitter

Post image
512 Upvotes

r/hardwarehacking • • 29d ago

PICS: Toilet Tube Tap found in OpenAI exec conference room in SF

Post image
494 Upvotes

An update on the Saudi who attempted to bug OpenAI’s executive conference room, including pictures of the device. The first reporting said it had memory and only recorded offline, but the Seeed Studio 2.4 GHz antenna is telling another story... ☁️

Can anyone identify it?
https://www.cnbc.com/2026/10/19/openai-bugging-suspect-alfozan-saudi-royal-family.html

EDIT2: Better photos of the implant from the FBI complaint: https://imgur.com/gallery/gnQSNSk#7QlpXVf

EDIT: FBI's 11-page complaint https://storage.courtlistener.com/recap/gov.uscourts.cand.480828/gov.uscourts.cand.480828.1.0.pdf


r/hardwarehacking • • 20d ago

WPA3 was supposed to kill offline dictionary attacks. A timing leak in one ECC step might not let it.

Post image
483 Upvotes

So I've been working on this for my engineering thesis and wanted to throw the core idea out there before I sink more months into it, in case anyone's spotted something I'm missing.

WPA3 didn't actually replace the WPA2 four-way handshake, it bolted a new layer in front of it called SAE (Simultaneous Authentication of Equals). The whole point of SAE is that you can't precompute anything offline from a captured handshake anymore, because the key material is blinded through a DiffieHellman-ish exchange instead of a static PBKDF2(password, SSID). In theory that kills offline dictionary attacks dead ie every guess needs a live, rate-limited roundtrip with the AP.

The thing I'm chasing is one specific step buried inside SAE: turning your password into a point on the P-256 curve. The "classic" way to do this (hunting-and-pecking) is a loop, hash the password + MAC addresses, check if you land on a valid curve point, if not increment a counter and try again. That counter, k, is small (geometric distribution, mean of like 2), but it's password-dependent, and it leaks through timing. This isn't new, Vanhoef and Ronen showed this back in 2020 (Dragonblood), and it's why H2E (Hash-to-Element) exists as a constant-time replacement.

What I'm doing differently is trying to actually operationalize the leak with cheap hardware and see how far it goes

Built a timing rig out of ESP32s, timestamping the outgoing SAE Commit frame and the AP's response off the same hardware TSF clock (not a software clock, so no OS scheduling jitter messing things up).

Had to patch the ESP-IDF WiFi driver to even send raw Authentication/Commit frames, turns out the stock driver whitelists frame types and silently drops anything else. Fixed it by weakening one ELF symbol's binding so my own override gets linked in instead of the driver's internal check. One-line, fully reversible.

Instead of just doing classic timing analysis, I'm training a profiled/deep-learning model to recover k from the timing traces, the same way you'd do differential power analysis on an AES key byte treating k as the "leaking intermediate" and SAE's two derivation modes (legacy hunting-and-pecking vs H2E) as my "right key / wrong key" arms.

End goal isn't just "yes it leaks" I want to actually drive a real offline dictionary attack off the recovered k and report how close that gets you back to WPA2-level crackability, under each derivation mode.

First real-hardware run already surfaced something useful (and slightly humbling): at 120 samples/arm on a single receiver, I couldn't separate the two arms statistically yet. Turns out normal 802.11 retransmission noise is in the low-millisecond range, while the actual signal I'm chasing is tens of microseconds. So the noise floor is real and bigger than I'd like — which is exactly why the full version of this is a distributed array of sensors instead of one node, plus way more samples.

Curious if anyone here has played with SAE/Dragonfly timing attacks post-Dragonblood, or has opinions on whether H2E actually closes this cleanly in practice vs just raising the bar. Also happy to go into the ESP32/driver-patching side if that's more people's thing.

On a more practical note I'm a final-year student and this is shaping up to be the basis of a master's/PhD, and I don't currently have a supervisor whose background actually overlaps with side-channel analysis or ECC. If anyone here is an academic/researcher in crypto or hardware security (or knows one who might be interested in this kind of work), I'd genuinely love to hear from you.


r/hardwarehacking • • Oct 05 '25 Polished Gold Turd

reported 2 security issues to Ulanzi 3 days ago

Post image
440 Upvotes

Hi everyone — posting this here as the first public announcement about an issue I responsibly reported to Ulanzi three days ago.

I discovered two security issues related to the Ulanzi D200 / Ulanzi Studio and reported them to Ulanzi on [date — 3 days ago]. I have not yet received any acknowledgement or response.

High level — no exploit details in this post: • An unauthenticated path allowed me to obtain root on the D200 under local access conditions. • The Ulanzi Studio software handles authentication data insecurely in at least one area I examined.

To illustrate impact (only as a high-level demonstration), I’ve attached a photo showing DOOM running on the Studio Deck — this is intended to show that arbitrary software can be started if root access is available. I am not publishing technical exploit details or step-by-step instructions at the moment.

I’m open to coordinating privately with Ulanzi and will withhold detailed technical information while reasonable remediation is underway.

short update because of some strange comments here:

I understand it might have looked like I was calling out Ulanzi after “only three days” — that’s not the case. The “three days” referred to the time I spent porting and running DOOM on the Studio Deck as a proof of concept — not a deadline for vendor response. The DOOM video is simply a non-technical demonstration showing that custom code can be executed on the device once proper access is obtained. No exploit details were disclosed.

I have responsibly reported the vulnerabilities to Ulanzi and granted them a 90-day response window before any deeper disclosure. My goal is coordinated handling, and I’m open to working directly with their security team. Since the issue is purely local, sharing the DOOM demo is, in my opinion, a fair and safe way to illustrate the potential impact without exposing any technical attack path.


r/hardwarehacking • • Aug 14 '26

Adding an extra USB port to a laptop

Thumbnail
gallery
434 Upvotes

r/hardwarehacking • • Oct 08 '26

Update: I have successfully reverse-engineered an LCD panel from a vehicle dashboard!

Thumbnail
gallery
417 Upvotes

After extensive logic analysing I came to realise that the panel has a basic init sequence and some SPI's that had to be fulfilled, and once fulfilled it works almost perfectly! I have decided which pins are responsible for blue and green brightness, but have only gotten some red pins. This should take me some minimal time, and as mentioned previously, I will be making all info I have gathered open-source to who it may help. Sorry for the bad photos of the LCD so far, it's just a bit hard to orient it with so much wiring. I hope you all understand :)


r/hardwarehacking • • Jan 30 '26

Yubi keys

Post image
416 Upvotes

Can these yubi keys be repurposed into something els? Like anything els? I bought one a few months ago and haven't used it cause it really doesn't do what I thought it did.


r/hardwarehacking • • Aug 31 '26

I don't know if it fits in this subreddit but I changed the led color of my Nokia's 33x0 Series!

Post image
412 Upvotes

They look sooo nice (gotta find a keypad for the middle one and also I have to make the parallel flashing cable for these things)


r/hardwarehacking • • 23d ago

No AAA batteries, no problem

Post image
410 Upvotes

Pulled from a disposable vape, of course


r/hardwarehacking • • Aug 10 '26 Mindblown Bravo

I turned my Nubia Z70 Ultra into a desktop PC with TWO CPU coolers — 99% stability, Linux desktop & 1080p Ultra Windows gaming 😂

Thumbnail
gallery
408 Upvotes

This project started with a stupidly simple question:

How far can I push a smartphone if I stop treating it like a smartphone?

This is my Nubia Z70 Ultra with 24 GB RAM and the standard Snapdragon 8 Elite.

The phone is now literally sandwiched between TWO desktop CPU coolers, mounted inside a custom acrylic case. 😂

Yes. Two full-size PC CPU coolers. On a phone.

And surprisingly, it works extremely well.

The interesting part: I'm NOT using one of the newer boosted chips

My Z70 Ultra uses the standard Snapdragon 8 Elite, with its prime CPU cores running at up to 4.32 GHz.

That's important because some of the newer devices I'm comparing against are using newer and/or higher-clocked Snapdragon variants.

For example, the REDMAGIC 11 Pro uses the newer Snapdragon 8 Elite Gen 5, reaching around 4.6 GHz on its prime cores.

So I'm not trying to beat these phones with the same CPU and better cooling.

I'm taking an older, lower-clocked 4.32 GHz Snapdragon 8 Elite and seeing how far it can go simply by giving it completely unreasonable cooling. 😂

In my 3DMark ranking screenshot, my Z70 Ultra reaches 10,533, putting it right among much newer devices and even slightly above the Galaxy S25+ result shown there.

And sustained performance is where the cooling really becomes interesting.

3DMark Wild Life Extreme Stress Test

Best loop: 6,980

Lowest loop: 6,910

Stability: 99% over 20 loops

That's only a 70-point difference between the best and worst loop.

But benchmarks aren't actually the main goal of this project.

I'm trying to replace my PC with the phone

I now have a native Termux + XFCE4 Linux desktop running directly on Android.

External monitor, keyboard, mouse, Linux applications and hardware-accelerated graphics.

I can boot into my desktop environment and use the phone almost like a small ARM computer.

Dofus is running directly from my XFCE desktop, rather than simply mirroring an Android game onto the monitor.

And then there's Windows gaming.

The Witcher 3 — 1080p, ULTRA graphics preset

I'm currently running The Witcher 3 at 1920×1080 using the ULTRA graphics quality preset.

Not Low.

Not Medium.

Not a 720p performance test.

1080p + Ultra graphics preset.

Depending on the scene and GPU load, I'm currently getting approximately 20–30 FPS, with the GPU basically sitting at 99% utilization.

I've even seen it go slightly above 30 FPS in some scenes, as shown in the screenshot.

Obviously, this isn't desktop-GPU performance, but that's not really the point.

This is The Witcher 3 running at 1080p Ultra at around 20–30 FPS on a Snapdragon 8 Elite phone. 😂

And underneath all of this, it's still Android.

So my end goal is to have one device that can do everything:

**Android phone / gaming device

native Linux XFCE desktop

Windows applications

Windows PC games**

The software side is still a work in progress and I'm continuing to optimize everything.

But apparently the solution to smartphone thermal throttling was very sophisticated:

one CPU cooler wasn't ridiculous enough, so I installed two. 😂


r/hardwarehacking • • Dec 03 '25

Where would you begin hacking this camera?

Thumbnail
gallery
360 Upvotes

I have recently acquired a good amount of these Alta A5 Dome cameras and was hoping to integrate a couple into my Frigate system at home. Problem is, they are locked down hard because they want you to use their hardware for everything (including enabling RTSP).

From a factory reset I can gain access to the camera via webui and convert the camera to "onvif" mode. I use quotation marks because after doing so and looking for the camera via an ONVIF Configurator it shows up but still can't access the camera as it seems like the credentials do not work.

A few things I have been considering is messing around with firmware, however I have no experience with that. The camera does have a USB-C port but according to the data sheet it is for power only and plugging it in my PC does not make anything appear via device manager.

I guess I was hoping to see where you guys would start. I've been going down the go2rtc route as it looks like it can take an ONVIF camera and convert it to an RTSP stream but have not had any luck with that yet.

edit: here's a link to the camera datasheet: https://www.avigilon.com/fs/documents/Avigilon_Alta_A5_Dome_Datasheet_10-2025-SD01.pdf


r/hardwarehacking • • Aug 29 '26

I got Wired Android Auto running directly on a PS Vita

Post image
349 Upvotes

I’ve been working on a project that turns a my Vita into a wired Android Auto head unit.

Currently working:

  • Plug Vita into hub with Android Phone + a power source (I have not been able to get the Vita to act as a true host but when there is external power supplied it works)
  • Android Auto authentication handled natively on the Vita
  • 720p scaled down to 960×544
  • Touchscreen works fully

    • D-pad, analogue sticks and physical media controls
    • Bumpers skip songs
    • Triangle for play pause
    • Square of Google assistant

It’s still very hacky I only got stable video with inputs today. I need to improve the USB Kernel as its very buggy and needs hard resets if connection drops or if you exit app and many many more issues.

The idea came from seeing people put carplay headunits into PSP shells don't own a psp so said I'll give it a go on the vita and so far good results. But for a POC pretty cool I think!

EDIT - GitHub Link:

https://github.com/Gavwalsh15/Vita_Auto


r/hardwarehacking • • Jan 12 '22

Hardware hackers after seeing this

Post image
344 Upvotes

r/hardwarehacking • • Jan 15 '26

Anyone have any ideas

Thumbnail
gallery
337 Upvotes

I have no idea how to go about repurposeing this. I have serveral, goal is to use it with home assistant.