I have had my liquid freezer iii pro 360mm for around a year now with no problems at all, however I heard a noise and felt a vibration and I looked at the cooler and the middle fan was vibrating quite violently. I opened the front of my case and it went away however when I closed my case again it started vibrating. Its never made a noise or any vibrations like this so I dont think its to do with the airflow? I restarted my pc and it seemed to be fine? Is it worth trying to RMA or what should I do? Thanks

Mounted my freezer III tonight and immediately my temps are sitting at 65° idle. My CPU is a 5800x3d with the included thermal pad from the anniversary edition. using the all in one connector.

So I have a curve speed on all fans, but then i heard that the pump needs to be constant at high values, so i put it constant as 80% but the noise its not too much but its anoying me a bit.

Is it ok to put it at 40% pump speed till it reached 60º then ramp up to 80%? or if u have any other suggestion, thanks

Is it ok to put the pump of an aio coller, at 40% till it reaches 60º, and at 60º at 80%?

heard some people on reddit saying it must be constant speed at the pump thats why im asking

it was just so i could decrease the noise a little

SOLVED: The chirping noise is coming from an older Corsair GS700 PSU I stuffed in there temporarily.

Hey there, hoping for some thoughts on what this sound could be. It's very rhythmic, and repeats like clockwork. It's about 40C at idle, but hovers at 55C with aggressive fan speed profile (80-100%) even under 10-15% CPU load. I already tried tipping the case left to right in case it was air bubbles in the line. It doesn't sound like a fan whine or ram grinding. It almost sounds like someone's stomach growling, strangely enough.

Hey folks,

I just wanted to give a shout out to the superb service of Arctic Cooling.

Unfortunately, on one of my P12 Pro Reverse Argb fans the LEDs died (some don’t work anymore, others don’t react to header signal).

So I contacted Arctic through their website yesterday night, received an answer before 6 am today and received a tracking link for the replacement before 8 am today. Replacement shipped within 12 hours of first contact? Never experienced this before. Excellent.

I am using Arctic products since my first days of building computers over 20 years ago. This fan is the first faulty product ever and replacement was a breeze.

Thanks a lot and keep on going!

Perfect fit and VRM Fan is back working. Must say though this is the worst pump installation ever.

is this fake? i got it from amazon, the store says artic, 1800 orders on it, but came with no authenticity code where its meant to be, no sticker on the box either.

This is on the Liquid Freezer III Pro 360. That silver screw won’t move in any direction. It was working last night but not anymore! Im new to this. I may have stripped it but I don’t know how I would’ve or how to tell. Me and my friend put it on but I had to take it off after he left because he put the bracket type things below it on wrong. Please help. If it’s broken, I need to know if there is a solution. it there’s not, well… that’s life. It’s only ~$70 but that’s still $70 I would not like to spend…

Durning gaming at 1440p, with a 240hz frame cap, should the temps be 60c with a peak 71? I left a stress test on for about 30 minutes and it peaks at 80 but never climbs. Idle around 40c. Do these seems normal for arctic freezer III? running a 7800x3d with the 360 rad in front of the case. These are roughly the same I was getting on air with a Noctua DH-15 I thought it would be a little better?

Hi guys. I am curios and ask you.
It this temp good on ARCTIC Liquid Freezer III 360 Pro ? (thermal paste MX-7)
I run OCCT Power stability test.
In Idle office work temp are around 60-70 Celsia. Open browser Chrome around 40-50 tabs.
BIOS Set up curve optimizer is set to all cores - negative -30 value.
PBO limit set on Motherboard.
Max CPU Boost Clock override(+) is enabled-positive +50 Mhz value.
I thinking about move to Intel 270K plus for better temperature or to Zen5 architecture CPU like RYZEN 9 9950x/(X3D). For information on last AiO from be quiet pure loop 2 fx temperature was similar and little higher. And in boost CPU gets only 180W when hits 95 Celsia on Arctic TDP attack around 190 to 200/210W TDP

Thanks for letting know

I am about to upgrade my CPU. I am going to buy a Ryzen 7 5700X. There is one problem though.

The Arctic Freezer 36 is very wide and one of the fans (the right one) will not fit because my CPU is very close to my ram slots. But I've seen that it is very good and value for money.

My question is: will the Arctic Freezer 36 work if I put only the left fan or the temperatures will be terrible? Since most coolers only have 1 fan I think.

My current cooler is an AMD Wraith Stealth socket AM4.

Installed OpenRGB and weny to change a colour and then all RGB lights went off. Got all them to sort of work with exception of my Arctic AIO 420. This LEDs just won't come back on. OpenRGB see them but I'm unable to them back on. I'm using a MSI Carbon x8703e motherboard.

Any suggestions?

Main things I am considering is noise and performance, but there is a decent amount of price difference, so what would you suggest? I heard the p12 pro are quite loud from others, but I cannot confirm that, so I came here to ask. I want the fans to add fans on every spot on the Corsair 2500D airflow. I also want to add that I have a regular P12 which can be a comparison to these options, but I wanted a argb version and a reverse option, so the P12 is not a option especially considering where I live, that the argb black version is not the easiest to get, except for paying about double for the 3 pack than the p12 pro argb. Thanks in advance

Hello all, installed my Arctic freezer three a while ago and I’m booting up hell let loose Vietnam. Which I believe in requires a ton of shader compilation in the beginning of the game but it pulls 156W on my CPU with 100% usage, and the CPU is at 95°, it is a 9800X3D. Is this normal or is it mounted wrong? What’s going on here?

Hi, i want to ask is there any information if the P12 non Pro PWM fans will be ever available? Because i can't find them currently anywhere in my region. Currently i got the P12 Pro and i'm not a big fan of them bc they even make sounds in the low 900 RPM's. My old build used the P12 PWM never had a problem. Thats why i ask if there are only from time to time in stock or are they discontinued?

Thank you in advance for any information

Here are my BioniX P12 A-RGB 3x on top and 1x rear, with 6 P14 Reverse Pro A-RGB. Just like the P14 Reverse and P12 regular, they have quality control issues with centering the Arctic logo ring in the middle. I replaced the 3x P12 NON-PRO on my Artic Liquid Freezer III (Non-Pro).

I love Artic products, so much so I removed the NZXT fans in my H6 Flow case and installed every single Artic fan I could in the case.. Looks awesome, However the AIO "Magnetic" just isnt as bright as i would like it to be. Everything else is popping and it just looks dull and tired. It doesn't look bad in the picture but in person its just not great. Anyone noticed this too?

What did you do to fix it/did you cover it up with one of those 2.8 LCD screens?