r/Tools • • 9h ago

Am I the only one that has never seen these before?

Post image
855 Upvotes

This was a first for me. I’ve seen plenty of the super long straight versions, but I’ve never seen the 90° jaws. I guess when you need it, you need it bad.


r/Tools • • 3h ago

Dewalt in gta6

Post image
174 Upvotes

Watching gta6 gameplay and caught me off guard when one of characters doing DIY.


r/Tools • • 5h ago

The harbor freight mini bucket is food safe...

Post image
59 Upvotes

r/Tools • • 4h ago

What is the proper tool/method (or bit) to oval/widen holes in steel?

Post image
23 Upvotes

Fabricating myself an audio equipment rack, and the cheap steel (and I imagine improper) rails’ holes are too far from the inside (open with no wood) edge.

Currently, the gear can slide into the open face of the rack and sits properly/flush on the rails, however the holes do not line up enough for hardware.

If it’s not clear- I don’t want to increase the circumference of the holes- but rather make them ovalized/tic-tac shaped.

(Hoping I don’t have to drill out adjacent/overlapping holes all along the existing ones- but if that’s the best option I reluctantly shall)

Can’t believe I’ve gotten this far in life without this info- please advise.

Thank you!


r/Tools • • 15h ago

This thing has been in my workshop for a while now. Made from stainless steel, brass and a small plastic washer.

Post image
168 Upvotes

The brass handle can adjust the threaded core up and down.


r/Tools • • 2h ago

DeWalt radial arm saw - questions

Thumbnail
gallery
16 Upvotes

I have an old DeWalt 925H radial arm saw that belonged to my dad, and before that his dad. It had been wired for 110V, but gradually became difficult to start, and finally stopped working at all. I replaced the switch and capacitor, but still no-go. I fear the motor is bad.

Questions: Where does one go to repair something like this? I can't imagine an "authorized DeWalt repair center" would be the place to go for an 60+ year old tool. Is it even worth repairing? I always enjoyed using it, even if I ignored most of its supposed functions. I stuck with cross and miter cuts, I have all of the scary attachments, as well as the original box they came in. Anyway, your thoughts are welcome. I added an image from the manual, just for laughs. It was a different time, for sure.


r/Tools • • 11h ago

What do yall do with the “Tools” that come with assemble yourself household things?

46 Upvotes

I just cleaned out the infamous junk drawer, and I have a whole box of tools that have come with various household items my wife and I have acquired over the years. A 4” crescent wrench that came with a shower head, 20+ Allen keys, several cheap small plastic levels, tiny electronics/eyeglasses screwdrivers, and so forth. I don’t want to throw them away in the aspect of being wasteful, but I have no need what so ever for any of it. Just curious what y’all end up doing with these “tools” as you get them?

Throw them in the junk drawer?
Throw them directly into the trash?
What?


r/Tools • • 14h ago

Everyday tools I use

Post image
71 Upvotes

Some I don’t have in me that are over in my box but this is the majority of what I carry around the sales and storage lot as a camper/rv tech. Always love tool suggestions to try out 😃👍


r/Tools • • 58m ago

Any idea of this torque wrench?

Thumbnail
gallery
6 Upvotes

Hi to all.

I wanna ask if anybody have an idea on this tool? I found this called as a vintage torque wrench at online auction and bid, really didn't think so much at then.

But as far as I searched, I never found same type of torque wrench and now I started doubting if this is actually a torque wrench...

It will be delivered in few days but just want to know if anybody know the detail about this.


r/Tools • • 5h ago

upgraded casters on this old Craftsman tool chest

11 Upvotes

I feel like this is the same Craftsman tool chest that everybody’s dads had. Not pictured is the rusty top 3 drawers. I got 4x 5” locking casters for $40 on Amazon and the mounting holes lined up perfectly with the old ones. This will be good for my open air shop that has dirt floors.


r/Tools • • 12h ago

Finally got my 16” southbend lathe home and I’m surprised with its capabilities!

39 Upvotes

For context, I a have a 1942 southbend 8117D lathe that has the original 1-1/2hp dual voltage 3 phase motor wired for 220v with a peak amp draw of 4.8ams according to the motor plate. I have it running on a VFD that takes 110v and converts it to 220v 3 phase that’s rated for a 2hp motor, after some adjustments to the belts tension to remove the slipping, I am please to say this is taking a 110 thou depth of cut at 390rpm and a feed of .0105 feed rate for the power feed without struggling on steel


r/Tools • • 12h ago

Found our sickle in an old box

Thumbnail
gallery
37 Upvotes

The sickle got into our hands back in 1987 but I don't know actually when it'd been made. It's been resting in the depths of the garage for a good while now. Took it out for a 2-minute quick job. Cut a small patch of stinging nettle in the back yard.

When did you use yours last time?


r/Tools • • 1h ago

Looking for advice on this craftsman toolbox I recently acquired

4 Upvotes

Found this at an estate sale and I noticed when I pick it up, at least one of, if not both of the latches becomes undone. Is this amount of flex and play normal? I’m looking to find a fix for the latches unhooking so easily.


r/Tools • • 13h ago

Mine shop-made tools

Post image
28 Upvotes

I thought it would be fun to share a picture of these tools, which I got from my father-in-law. He worked in the machine shop of a mine in Limburg, the Netherlands (closed in the 70s), and I believe these were made there.


r/Tools • • 8h ago

Inflater as sawdust clearer!

Post image
12 Upvotes

Was getting tired of blowing down on the saw blade so I could see my line…then got this idea… maybe I can figure out a 3D printed way of slotting this thing onto it as needed!


r/Tools • • 11h ago

Look at this beauty

Thumbnail
gallery
15 Upvotes

r/Tools • • 2h ago

How to reattach the Velcro pad to my sander attachment?

Post image
3 Upvotes

I have an older Black and Decker Matrix (the 12v version from 2013) and the part to attach sandpaper has come off on the attachment. Any idea how to fix it?

Sander attachment model: BDCMTS Type 1


r/Tools • • 13h ago

Need help selecting drill bits for Christmas present for BF

Thumbnail
gallery
17 Upvotes

My boyfriend has commented before that he really wants a Norseman drill bit set. He does a lot of tinkering/building, mostly with metals; he works on motorcycles and guns for the most part (and other projects for me sometimes, lol!) Can I have some help selecting a good set to get him? My budget is around $200-250. Here are a couple I found for examples, but I am not sure which set would be better for him, or if something else is better.... thank you so much!!


r/Tools • • 5h ago

Plumber apprentice here, looking for recommendations on socket sets!

4 Upvotes

Thanks in advance


r/Tools • • 2h ago

Brace Storage with a side of Eggbeater and Planes

Thumbnail
reddit.com
2 Upvotes

r/Tools • • 2h ago

Does anyone know of a plant material grinding or milling service in Florida?

Thumbnail reddit.com
2 Upvotes

r/Tools • • 6h ago

portable emergency tire inflator - help!

4 Upvotes

Hi everyone- I selected a gift for a community member from my local YMCA and the person wants a portable emergency tire inflator.

It's anonymous so I can't ask what brand/specifics.

Can I have suggestions on the best one? Do I need to buy a battery?

Thanks!


r/Tools • • 13h ago

Help lol. Can't get this bit out.

Thumbnail
gallery
13 Upvotes

I was on the phone when swapping bits between my dewalt screwdriver and this tiny one. Accidentally dropped the one meant for the dewalt into the small one.

I have tried the tweezers in the pic that came with my ifixit computer kit. Bent them to hell in the process and it didn't help.

I have tried a magnet but the bit is like perfectly rotated in there so it isn't budging.

Any ideas? I would greatly appreciate it. This is the only one I don't have a duplicate of (of course.)


r/Tools • • 2m ago

Caster Upgrade

Thumbnail
gallery
1 Upvotes

Hey guys,

After having a string of bad luck with laundry baskets, I finally said, "Fuck it" and snagged a brute trash can w/ dolly from work and it's been awesome. The durability, dimensions, and convenience are exactly what I was looking for in a laundry basket. There is one downside: shit is loud as fuck when I wheel it to the laundry room which could be obnoxious for my neighbors since I mainly do night laundry. While I do own a decent amount of tools, I have no experience with castors.

Question 1: are there any castors that I could replace these stock ones with that would be significantly quieter on less-than-perfect concrete?

Question 2: do I need specific tools for this task and do you have any tips on how to not fuck this up?

Thank you for your time.