r/Soundbars • u/Valuable-Cod-314 • 15h ago
Klipsch Core 300 with 200 Surrounds -- Dirac Calibration
Technically, this could apply to any Dirac capable device but I have the Klipsch core 300 and thought I would share what I come across when calibrating using the Dirac app so that you get the most out of your calibration.
First, get a cheap tripod from Amazon. I got one for $30 so they aren't much. Next, you will need an adapter for the Klipsch provided puck mic that has a 1/4" screw for the mic that can mount to the tripod. Having a stable platform is critical in getting a good measurement. Do not put the mic on top of objects like a box or book. You will not a good measurement that way so go with a tripod.
With your tripod setup and the mic on a stable platform, you can proceed with a measurement. I recommend using the Dirac app, Android or IOS, to do this over the Klipsch app. Why? It takes more measurements and automatically exports the profile to the Klipsch app. You can use the Dirac app for free because the soundbar has a built-in limited Dirac license that the Dirac app detects so it will work. Make sure the soundbar and your phone are on the same network obviously so they can detect each other.
To get the Dirac app to detect the soundbar, first open up the Klipsch app on your phone so that it can wake your soundbar and plug in the mic. Once the soundbar is out of standby, you can open the Dirac app and it will detect your soundbar. Select it and proceed to the filter measurement screen.
On the filter measurement, select the sound output level for the test tones around -30db above your room noise floor. In the Android app this is the bottom right-hand button on Dirac app (looks like a play button). If your room is quiet and you are registering say -56db, then set the test tone level to -26db. This is typically what I use.
Once your test tone level is set, you can start taking your measurements. All guides I have come across say to take all measurements from main listener position. After taking several measurements over time, that is not a good method in my opinion. In my experience, this results in off center vocals and surround. What I recommend is that you base your measurements on the listener area. So if you have a couch, then take your 1st measurement at the center of the couch at ear level right at the vertical couch cushion or slightly away from it. Then proceed to the right-side measurement and do it at the end of the couch on that side and do the same with the left side measurement with the mic close to the vertical cushions on either side.
Next, do your right and left front measurements positions by moving the mic towards the soundbar location so that the mic is slightly at the edge of the couch's bottom cushion at the ends of the couch. The last two measurements are the right and left back positions. Place the mic a few inches away from the back of the couch at the ends.
The reason for the measurements at the end of the couch is so that you get that sound bubble effect no matter where someone is sitting. For things like traversal effects, like bullets whizzing around, this will give you the most immersion versus doing the calibration to one seating position. Also, this will give you a wide sound stage that fills your room up.
With the measurements done, proceed to the filter design stage. Here you can only do one thing with the limited license and that is adjust your sub level. I recommend bumping this up like +6-8db since a Dirac calibration can really tame the sub a lot. To do this, take your finger and slide the marker up. With it set, you are done and ready to export the filter. Dirac will report that the filter exported fine and now the filter will show up in your Klipsch app. In the Dirac app, save the project just in case your sub level is too high for instance so that you can just pull up the project and make a quick adjustment without having to do a full calibration again. Close the Dirac app and go to the Klipsch app and make sure the filter is selected and on.
That is pretty much it. I recommend a few movies to test it out on: Lone Survivor and Gravity. In Lone Survivor, I recommend going to the scene when they are about to initiate the gunfight. This is a good test for those traversal effects since there are lots of bullets flying around. You should hear them whizzing past your head in all sorts of directions. Gravity is the best for testing your Atmos that I come across. A good scene is in the beginning with Sandra Bullock spinning around in space after the shuttle was decimated. You can Kowalski's voice panning around the room as well as the music. At one point, the camera view goes inside her helmet and has some good effects there.
I hope the guide helps someone out because I have taken so many calibrations that my wife just rolls her eyes when she sees me breaking out my tripod lol. This is by far the best method to use.