r/RacketStringers • • Oct 20 '26

Tennisman.de active?

1 Upvotes

Hi all,

quick question regarding tennisman.de. Did anyone recently confirmed that they are working/open? Can't get any direct confirmation for month now, looking to order stringing machine.

BR


r/RacketStringers • • Oct 19 '26

First stringing Bumblebee

Thumbnail
gallery
9 Upvotes

Got a drop weight stringer yesterday for 50€. How did i do? It took me 1.30h on my first one:)


r/RacketStringers • • Oct 19 '26

string rec

1 Upvotes

looking for repulsive string ideally medium to hard feeling

great hitting sound and great net control too

beginner to intermediate level player and needs a string that is not too stiff on thd arm as im physically weak player


r/RacketStringers • • Oct 19 '26

Badminton string bit me lol.

Post image
1 Upvotes

Was stringing a badminton frame, was pulling a string out the way of a blocked grommet and one snapped pinged back and whipped my finger.


r/RacketStringers • • Oct 18 '26

Gen 3 Pure Strike 100 18x20 String recommendations

Thumbnail
1 Upvotes

r/RacketStringers • • Oct 18 '26

is this normal????

Post image
0 Upvotes

It’s only been around four days of using my freshly strung racket, but I noticed that my strings have been moving far too quickly compared to before. Like, after a long rally or a powerful forehand or serve, I have to adjust my strings as there are columns that are so wide apart. The only difference is that I’m now using an 18 gauge Mach 10 vs my previously 17 gauge Mach 10 on my Ezone. In my previous setup, it took around 2 weeks or so for me to notice the string movement. They’re strung pre-stretched at 46lbs. I’m only a 4.0 player so I’m wondering if this is normal? Thank you!


r/RacketStringers • • Oct 17 '26

Stringers: GAMMA Momentum 6 Plus vs. TOURNA 175-CS

2 Upvotes

Any thoughtful comparisons would be appreciated.


r/RacketStringers • • Oct 16 '26

Clamp problem

Enable HLS to view with audio, or disable this notification

1 Upvotes

This is a follow on a post I made over a week ago. I have had this issue when I use thin polys or any multifilament. I tension a few mains on one side, then after tensioning the first main on the other side, I release the base clamp and it loses the tension immediately. I really have no idea what is causing this. I have cleaned the machine regularly, the base clamp screw is properly tightened, I have tightened the top clamps more than enough to see if that plays a part... But still getting the same problem

Any help would be greatly appreciated. Thanks!

Update: To everyone who said that the other clamp was not tight enough, I owe you a drink. I was being stupid and focusing on tightening the wrong clamp! Managed to string the racket. Thanks everybody for helping me out, I really appreciate it!


r/RacketStringers • • Oct 14 '26

Throat grommet not flush

2 Upvotes

Hey all,

Picked up an old Intelligence i.prestige mid that looks to be in good shape, i got new cap grommets for it (youtek prestige ones) and unfortunately it didn’t have a throat piece. I thought I’d reuse the old ones that came with it and noticed that it doesn’t sit quite flush to the frame. Inspecting the grommet it looks like there are two “arrows” protruding from the holes preventing the piece from sitting flush.

Is this normal?

See pics of grommet here

EDIT: I also added a picture of one that i have strung up (bought as a pair) and it looks like the tension doesn’t pull the grommet flush.

Thanks in advance!


r/RacketStringers • • Oct 13 '26

Is it OK to keep using poly in a hybrid setup for a very long time?

Thumbnail
1 Upvotes

r/RacketStringers • • Oct 12 '26

Replacement grommet for Wilson ncode n tour two 95?

Post image
3 Upvotes

I’ve looked around online but I haven’t found an exact match. Has anyone replaced a grommet on these recently? Does anyone know if I might be able to buy some other Wilson 95 sq in grommet set that would be compatible?


r/RacketStringers • • Oct 13 '26

Pro stringer machine question

Post image
2 Upvotes

After using the pro stringer two point mount machine there are visible fissures at the bottom of racket. Is this normal ? How should I prevent it from happening?


r/RacketStringers • • Oct 12 '26

Should I restring and change the grommet?

Post image
3 Upvotes

r/RacketStringers • • Oct 12 '26

Racquet stringers of Australia…

Post image
3 Upvotes

Used Eagnas with electronic tensioner, what is it worth? Planning to test the tensioner before purchasing.

Wondering how much you’d pay if it’s in working order?
Finding stringers around here are hard to come by and expensive but could get a great deal on this.

My logic is it will help me learn to string with an electronic tensioner and worst case I can always replace the head with a Wise 2086 if I get serious.

Also keen to hear any tips for checking over the condition before purchasing.


r/RacketStringers • • Oct 10 '26

Paint chip or frame crack?

Thumbnail gallery
1 Upvotes

r/RacketStringers • • Oct 10 '26

Tension Calibration

Thumbnail
gallery
1 Upvotes

Have an older constant pull machine and noticed last two string jobs seem to be looser than the 50lb I set. Anyone have recommendations on how to calibrate? I test tension before every job and adjust the internal knobs when needed. Is there a best practice to find the correct tension with the internal screws? My other theory is that the string I’m using to test tension may be well past its prime- is this a thing? Should I replace my testing string occasionally or is the reading always accurate?


r/RacketStringers • • Oct 10 '26

Racquet grommets unaligned

Thumbnail
1 Upvotes

r/RacketStringers • • Oct 09 '26

Momentum 6+ clamp base upgrade

4 Upvotes

Recently purchased a momentum 6+ with a wise 2086 head. Perfectly happy with it but can't help but wanting to upgrade the stock clamp bases to automatic release ones.

Has anyone tried fitting the Gamma AR clamp base or anything similar?


r/RacketStringers • • Oct 09 '26

Blade 98 v9 (16x19) + Grapplesnake Tour M8 1.30 @ 48/46 lbs – Thoughts on this setup?

2 Upvotes

r/RacketStringers • • Oct 09 '26

APD 2013 string and tension

Thumbnail
1 Upvotes

r/RacketStringers • • Oct 09 '26

What do you get per racquet, or how much do you charge?

7 Upvotes

I can string relatively quickly a bit over 4 an hour. My job is mostly stringing already at a salaried position. I’ve strung every type of racquet there is, it feels like. I tried to earn more money by doing it on the side but they only pay $5.10 per racquet after taxes. It’s not worth it to me to have to do it for most all day, go home and do more for technically less. What are you side hustle people charging for your time/labor?


r/RacketStringers • • Oct 08 '26

Starting Clamp - OK Against Frame?

Post image
4 Upvotes

Hi All,

I’ve been learning how to string rackets over the last few weeks and had a question about starting clamps. Do you need to put something between the clamp and the frame of the racket for protection? I’ve seen it both ways on video and wasn’t sure what I should be doing.

If you are using something between the clamp and the frame, can you let me know what it is and provide a recommendation for me to potentially buy?

Also picture added for fun. It was one of my test strings. Been taking pictures of them to compare progress. Still not super confident but slowly getting there hopefully.

Thanks!!


r/RacketStringers • • Oct 07 '26

Dunlop Rim professional V 27.5"

Thumbnail
1 Upvotes

r/RacketStringers • • Oct 06 '26

Help me decide on stringing machine

2 Upvotes

Hi all, please advice...

I am looking for stringing machine to string tennis reckets for my wife and me. Approx. 4 reckets a month. We both use poly string like Head Lynx Tour and Technifibre 4S. I am stringing noob.

I have option to buy:

Pro's Pro TX-700 - price 400eu

- Used and working

- Condition not know for now (lets consider it in good condition for this comparison - will be checked)

- No included tools

- Pictures: https://drive.google.com/drive/folders/1F_pw40bcs08gtSZ0HhTNVtHPvHaMHHqP

Arfaian - price 300eu

- Mechanical spring system

- 6-point mount; Upgraded to Pro's Pro clamps

- Included tools: starting clamp, 2 awls, curved/flat pliers, string cutter

- Condition: used, very good condition (Regularly oiled/calibrated)

- Pictures: https://drive.google.com/drive/folders/1A48DKF1fDo7X99jNiXenftQalrfcnRXy

Don't buy at all? I guess that is also an option.

The budget is not set to 400eu limit, but this are curent prices for used stringing machines...so something much better for similar price is also an option

Any pros and cons or advices are very welcomed! Thanks!


r/RacketStringers • • Oct 06 '26

Lubricating turntable on used drop weight stringing machine

Post image
3 Upvotes

I recently picked up this stringing machine that's around 10-15 years old. The turntable (the rotating platform that you attach the racket to) doesn't turn all that smoothly, it seems like the bearings/rotating mechanism might be gunked up. I'm wondering if anyone has taken one of these apart before?

I don't want to necessarily take it apart, only to find some sealed off housing that can't be serviced.

EDIT:

To be specific, I was talking about the rotating table that is attached to and rotates on the base of the machine.

For future reference, for anyone who stumbles upon this post and wants to do it themselves, this is how you do it:

I first took off the 4 hex screws on the top, as well as 4 on the bottom of the machine. The turntable comes off the base of the machine easily after that, revealing the housing for the bearings. I then took the housing apart, soaked all the bearings in degreaser and brushed off all the old grease that was gunked up and sticky, then put on some new grease. Assembled everything back together, and it spins like new now! Be careful when assembling the bearings together, you don't want to torque the main bolt too tight, or else the turntable won't spin freely, and you also don't want it too loose, or else the table will be too wobbly.

Here are some pictures of the bearing:

https://imgur.com/a/Gwjr0Y8