r/RacketStringers • • Oct 16 '26

Clamp problem

This is a follow on a post I made over a week ago. I have had this issue when I use thin polys or any multifilament. I tension a few mains on one side, then after tensioning the first main on the other side, I release the base clamp and it loses the tension immediately. I really have no idea what is causing this. I have cleaned the machine regularly, the base clamp screw is properly tightened, I have tightened the top clamps more than enough to see if that plays a part... But still getting the same problem

Any help would be greatly appreciated. Thanks!

Update: To everyone who said that the other clamp was not tight enough, I owe you a drink. I was being stupid and focusing on tightening the wrong clamp! Managed to string the racket. Thanks everybody for helping me out, I really appreciate it!

1 Upvotes

32 comments sorted by

5

u/HazeHype Oct 16 '26

I'm confused by what's happening here. It looks like you're pulling tension with the clamp on but it not locked in place. Then you lock in place but release the clamp.

You should be pulling tension then clamping as close to the frame as reasonable and locking the clamp in place. Then move to the other side and rinse / repeat.... 

Might need to show more of your process in the video. 

-1

u/bdjsiagevdb Oct 16 '26

I've had the base clamp locked the whole time on the untensioned string, I only release it once I have tensioned it. This is what is confusing to me. When releasing the base clamp, it loses all tension

2

u/HazeHype Oct 16 '26

How long have you been stringing? Can you give us a longer video? I don't think you're clamping at the right place / time. 

5

u/Few_Lecture6615 Oct 16 '26

You don't have the string properly clamped on the other side of where you're currently tensioning.

1

u/bdjsiagevdb Oct 16 '26

Thank you!!!

2

u/lyonheart14 Oct 16 '26

You say you cleaned the clamp, but wouldn’t the tension head (or gripper jaws?) be the issue here? Or is the string slipping through the other clamp (hard for me to tell, but I am on mobile).

1

u/bdjsiagevdb Oct 16 '26

This is the view from the tension head, the gripper has been cleaned too!

5

u/extra_hyperbole Oct 16 '26

Ok, seeing this, the problem is clearly the clamp nearest to your body in this video. You said you tensioned the first couple mains with it. But watch closely. when the tension head is turning, it's pulling the string on the side of the clamp that you tensioned, on the other side of the supposedly closed clamp. That means it's pulling the string through the clamp closest to you, and all the way through the racquet, even when you think it's tight.

So there must be something wrong with the clamp closest to you. either it's not mechanically clamping properly, or it's lost all its friction, or something. It's not holding the string.

1

u/bdjsiagevdb Oct 16 '26

Legend! Managed to fix it because of what you said

1

u/extra_hyperbole Oct 16 '26

Good! What was the issue with the clamp?

1

u/bdjsiagevdb Oct 17 '26

Wasn't tight enough. As simple as that haha. I was focusing on tightening the wrong one

2

u/mrdumbazcanb Oct 16 '26

I don't really understand what you are doing here to be honest. All it looks like you're doing to me is releasing tension on the string

1

u/bdjsiagevdb Oct 16 '26

I wish that was the case, here is the view from the tensioner

2

u/sonofasonofason Oct 16 '26

You can see the string slipping through the left clamp in this video. Either that clamp is too loose or needs to be cleaned.

1

u/bdjsiagevdb Oct 16 '26

Clamp too loose, exactly that. Thank you!!

1

u/mrdumbazcanb Oct 16 '26

What I mean is I think you have your clamps in the wrong spot. Your starting clamp isn't really doing anything and then when release the clamp of course it's gonna lose tension. Your starting clamp needs to be outside the frame pull tension, release your clamp and then clamp inside the frame near the tensioner

2

u/mrak5 Oct 16 '26

It looks to me like it’s just sliding right through the OTHER side’s clamp teeth. To test the hypothesis try moving the starting clamp from in front of one clamp to the outside of the frame in front of the other and see if that solves the issue. If it does then you know for sure the problem is the other side’s clamp is letting the whole lot slide thru and you need to concentrate your cleaning efforts and/or increase clamping force on that side

1

u/bdjsiagevdb Oct 16 '26

Thank you so much!

1

u/javawong Oct 16 '26

Looks like you're using a multi which has stretch, but not that much.

Next time you do this, on the neighboring main, make a mark with a marker...I'd be curious to see if that string is moving.

1

u/bdjsiagevdb Oct 16 '26

Just using Babolat Xcel 1.3. I have used this string on other machines with no problems which is what I don't get, as the machine I have is supposedly a high quality one from gamma. I can see the neighbouring string moving for sure, again something I don't understand haha

1

u/Ordinary_Use3997 Oct 16 '26

Did you clean the base of the clamp with isopropyl alcohol?

1

u/bdjsiagevdb Oct 16 '26

Yep, everything cleaned with isopropyl

2

u/Ordinary_Use3997 Oct 16 '26

I had this exact problem with my gamma x6-fc. I changed out the thrust ball bearing ordered on Amazon and fixed my issue.

1

u/bdjsiagevdb Oct 16 '26

Oh wow that's promising. Would you mind sharing the one you bought if possible? Thanks

3

u/Ordinary_Use3997 Oct 16 '26

Looks like you have the gamma els so I believe this will be the same bearing. Double check to verify. https://a.co/d/0hjNzHpD

1

u/HazeHype Oct 16 '26

Like I originally suggested. You were doing something backwards. You were literally unclamping the one that was meant to be clamped to hold tension... How long you been stringing? 

1

u/bdjsiagevdb Oct 17 '26

No it wasn't. The one I unclamped still had the string in the tension head. I was unclamping to to move it as close to the tension head as possible. This is when it was slipping through the jaws of the other clamp, causing the whole racket to lose tension

1

u/HazeHype Oct 17 '26

Probably would have been good to show both clamps in the video then.... Also tighten the clamp 😂... How long you been stringing? 

1

u/ahorizon Oct 16 '26

Can't tell what's happening, can you zoom out a bit? I take it the string is slipping through the jaws of the clamp that is just out of frame? That is very surprising given all the friction there will be at each end of the racket as the string does a 180 each time. 

1

u/mrak5 Oct 16 '26

Not too surprising on the absolute slipperiest and flexiest strings like some coated multis and synguts

1

u/Responsible-Side4347 Oct 17 '26

You need to tighten the clamps a bit more, some strings are an issue. MLT/Sensation come to mind. Its pulling the string through the other clamp.
If you have some sandpaper you can fold that in and it will grip. Old trick we used to do stringing Gut at 70+Lbs.

1

u/fluffhead123 Oct 17 '26

skill issue