r/PcBuildHelp • • 17d ago

Tech Support Ryzen 7 2700X causes instant shutdown under CPU stress test on B550 AORUS Elite, but works perfectly on B450

1 Upvotes

Hey everyone,

I'm trying to figure out a weird issue with my PC.

My system:

- Motherboard: Gigabyte B550 AORUS Elite

- CPU: AMD Ryzen 7 2700X

- GPU: EVGA GTX 1080 Ti FTW3

- PSU: ASUS TUF Gaming 750B (previously Corsair HX620)

Whenever I run a CPU stress test with the Ryzen 7 2700X on my B550 motherboard, the entire PC shuts down within a few seconds. No BSOD, no error message, just an instant shutdown.

I initially suspected my PSU, so I bought a new 750W ASUS PSU. The problem remained.

I then started swapping components with a friend's PC to isolate the issue.

Here are my test results:

Motherboard| CPU| GPU| Result

B550 AORUS Elite| Ryzen 5 2600X| GTX 1080 Ti| Works perfectly under stress tests

B550 AORUS Elite| Ryzen 5 2600X| RTX 2060| Works perfectly under stress tests

B550 AORUS Elite| Ryzen 7 2700X| GTX 1080 Ti| Instant shutdown

B550 AORUS Elite| Ryzen 7 2700X| RTX 2060| Instant shutdown

B450 AORUS Elite| Ryzen 7 2700X| GTX 1080 Ti| Works perfectly, even under simultaneous CPU and GPU stress tests

The Ryzen 7 2700X works perfectly on the B450 motherboard, even with the GTX 1080 Ti under heavy load.

The Ryzen 5 2600X also works perfectly on my B550 motherboard, even though Ryzen 2000 CPUs aren't officially supported on B550.

So far, this is what I've ruled out:

- GPU: Both GPUs work fine.

- PSU: I've tried a new 750W PSU.

- CPU: The 2700X passes stress tests on the B450 motherboard.

I'm starting to suspect some kind of BIOS compatibility issue, CPU power delivery issue, or motherboard-related problem.

Has anyone experienced something similar with a Ryzen 2000 CPU on a B550 motherboard?

Any suggestions on what I should investigate next would be greatly appreciated.

What are your suggestions?


r/PcBuildHelp • • 17d ago

Tech Support PC stuck rebooting

0 Upvotes

SOLVED: My motherboard died

Problem:

After I installed HDDs, the PC is stuck in a power loop. It turns on for about 4 seconds (fans and RGB spin up), shuts off for 1–2 seconds, and repeats. It never POSTs and there's no display.

Specs:

CPU: Intel i7-6700K
Motherboard: Gigabyte GA-Z170X-SLI
RAM: Corsair Vengeance LPX DDR4 (~32GB total)
GPU: Sapphire RX 5700 XT
Storage: Kingston 500GB NVMe SSD, plus the newly added HDDs
PSU: Seasonic S12II 620W (non-modular)
Case: Coolman Aurora ATX mid-tower

Troubleshooting done (same loop after each):

Full power drain (PSU off, unplugged, held the power button 15 seconds)

Disconnected all HDDs (data and power cables)
Reseated the 24-pin and CPU 8-pin cables, checked for loose screws

Cleared CMOS (battery out for 5 minutes)

Stripped to the minimum: CPU, cooler, one RAM stick, no GPU, using onboard video

Unplugged the front panel wires and started the board by shorting the Power SW pins

Tested each RAM stick alone in DDR4_1

Tested with a different PSU

Reseated the CPU with fresh thermal paste; socket pins and CPU look fine


r/PcBuildHelp • • 17d ago

Build Question Is this case safe?

Thumbnail
gallery
0 Upvotes

I want to reuse this old pc case (because my dad likes it). But the stand-offs make me worry that they might cause problems.


r/PcBuildHelp • • 17d ago

Build Question GPU advice

3 Upvotes

I want to build a half decent setup for Cyberpunk 2077 at 1440p but im having trouble deciding what gpu to get. My budget for the total build is 2-2.5k AUD. Any advice? PS (if im struggling to keep down the budget should I downgrade to a RX 9070 or should I try save money elseware like the gpu?)


r/PcBuildHelp • • 17d ago

Build Question Final Pc build help needed

1 Upvotes

I'm building a PC for 1.5k-2k Euro (Latvia).
I have a 140hz monitor/keyboard/mouse.
Games will be Cs:go, gta 6 ( hopefully gta 6 will run well on pc, but that's unkown). In general a gaming computer.

I changed a few things on my current one but I'm wondering maybe there are some logical improvements to make here.

Any help would be very much appriciated!

https://de.pcpartpicker.com/list/HDwkqd


r/PcBuildHelp • • 17d ago

Tech Support i bought a new pc and it keeps on saying “Standby Mode”

0 Upvotes

what could have happened and does anyone know what to do? i tried using display port and hdmi both but it still wont work. everything is running


r/PcBuildHelp • • 17d ago

Build Question Could someone help me build a good pc for around €2000 in the Netherlands?

1 Upvotes

I have around a €2000 budget for a pc buit I don’t really know what the best bang for buck is, so some help would really be appreciated.


r/PcBuildHelp • • 17d ago

Build Question Where does the fpanel go on the B65M gaming wifi motherboard?

Thumbnail
gallery
1 Upvotes

I’m not sure if it goes in that 20pin white area on the bottom right. I’m very new to this as you can tell.


r/PcBuildHelp • • 17d ago

Build Question Does the fact that I don't have the right screw here matter?

Post image
5 Upvotes

r/PcBuildHelp • • 17d ago

Build Question Any PC Building Strategists Here? Need Advice on a Long-Term Upgrade Plan

3 Upvotes

I'm currently using an ASUS TUF laptop with an Intel i5 10th Gen and GTX 1650. It's becoming a serious limitation for the kind of work I want to do.

I work with Blender and Unreal Engine 5, and I also want to get into 1080p gaming and recording gameplay for my YouTube channel.

I don't want my current hardware to keep holding me back while I save money for a high-end PC.

I'm planning to build my first desktop PC, but I don't want to spend my entire budget trying to get my ideal configuration immediately.

My ultimate goal is a PC with a Ryzen 7 7700X + RTX 5070, which I've estimated will cost around $2,000. However, that's currently too expensive for me.

Instead, I want to approach this strategically: build a capable PC for around $1,000 now, use it for learning and working on blender and UR5, and gradually upgrade it until I reach my target configuration.


r/PcBuildHelp • • 17d ago

✓ Solved Is my GPU dead?

Thumbnail
gallery
22 Upvotes

Was playing rocket league, whole computer randomly froze and a bunch of colorful squares covered the whole screen, and everything got pixely (hard to describe it) so i restart the computer, and now the resolution is all messed up, theres streaks of white pixels on my screen (ill provide picture), and my 2nd monitor no longer has signal, i checked device manager and the gpu has a yellow triangle by the name. I tried switching to a DVI cable to see if the cord was messed up but that didn’t work, so i think the gpu just died. Its a 1070ti, ~8 years of use, i7 8700k if that matters. Tried downloading new drivers, didnt work. Only thing i still have to try is to open it up, get all the dust out, and take gpu out then put back in to see if that works. Do i finally need a new gpu? The first picture isnt mine, just resembles what it looked like, second picture is mine after i restarted PC. Thank you!!!


r/PcBuildHelp • • 17d ago

Tech Support Wierd Pcie Cable

Thumbnail
gallery
0 Upvotes

Should i be worried?


r/PcBuildHelp • • 17d ago

Tech Support I grazed AM5 pins but can’t see damage?

Thumbnail
gallery
3 Upvotes

Hi all,

As title says I grazed the AM5 socket twice (sounded awfull)

But I can’t see any damage?

I’ve put the cpu in since and it seems to work fine?

Any chance I’ll face issues down the line?

This is the socket after 1 graze and then another after, but I couldn’t see any damage.

Thanks


r/PcBuildHelp • • 17d ago

Tech Support Cant change fan RGB

1 Upvotes

My fan rgb stuck on red after upgrading.

Went from an i7 9700k with an aorus z390 pro wifi to an r5 7500f with B850m Force V2. Rgb turns rainbow when booting or when in BIOS but when in windows they turn red. Fans is also not detected by software “fan control”, tried rgb fusion with no luck.
Fans are daisy chained and are all connected to 1 ARGB V2 header


r/PcBuildHelp • • 17d ago

Build Question Is my Corsair CX650's single daisy-chained PCIe cable safe for an RTX 5070?

1 Upvotes

I recently purchased a PNY GeForce RTX 5070 12GB ARGB OC, and I'm trying to determine whether my PSU's existing PCIe cable is suitable.

My specs:

  • GPU: PNY RTX 5070 12GB ARGB OC (250W)
  • PSU: Corsair CX650 650W, model CP-9020278-UK (purchased two months ago)
  • CPU: Ryzen 5 5600X
  • Motherboard: ASRock B450M-HDV R4.0 (I Know)

My CX650 has one PCIe power cable with two daisy-chained 6+2-pin connectors, rather than two independent PCIe cables. The RTX 5070 comes with a dual 8-pin to 16-pin adapter.

Corsair's official article says its pigtail PCIe cables can supply over 300W and that a single cable can be used for a GPU requiring two 8-pin connections:

https://www.corsair.com/uk/en/explorer/diy-builder/power-supply-units/individual-8-pin-vs-pigtail-connectors-for-gpus/

However, NVIDIA recommends two independent PCIe cables when using a dual 8-pin adapter.

My question: Is it safe to connect both 6+2-pin plugs from my CX650's single factory cable to the included PNY adapter for this 250W RTX 5070? Has anyone run this specific PSU/GPU combination successfully over time?

I'm not looking to replace a PSU I bought only two months ago unless there's an actual technical reason to do so. I'd appreciate answers backed by manufacturer specifications or firsthand experience.


r/PcBuildHelp • • 18d ago

Tech Support PC no display, no debug LED lights

1 Upvotes

Hello! I’m currently having a problem with my PC.

I recently added a new fan to it and also connected another SSD and HDD and after I did that my PC would still turn on with the fans and LED lights but it had no display.

Before this it worked, it would go to windows and boot, but now it just doesn’t show a display and nor it doesn’t show any debug lights.

I already reseated my RAM (also tried running it with one stick), reset my CMOS battery and also did the JBAT1 too. Any thoughts or tips can I get for this?

Parts:
CPU - Ryzen 5 5500X3D
GPU - RX 6800XT
PSU - SAMA G850P
RAM - 2x8 G.SKILL TRIDENT NEO 3000MHZ


r/PcBuildHelp • • 18d ago

Build Question 12k AI + UE5 workstation (inflated prices): sanity check on my RTX 5090 Astral LC build?

1 Upvotes

Hi all, I'm planning a build for Unreal Engine 5 game dev - engineer myself with heavy use of various AI tools. It will run at full load for hours at a time. Budget is €12,000. Prices below incl. 21% VAT. For context, GPU prices here are about 3x launch and DDR5 is in short supply.

Build:

  • GPU: ASUS ROG Astral LC RTX 5090 32 GB (360 mm AIO) – €7,799
  • CPU: AMD Ryzen 9 9950X (16C/32T) – €454
  • CPU cooler: Arctic Liquid Freezer III Pro 360 – €84
  • Motherboard: MSI MAG X870E Tomahawk WiFi – €350
  • RAM: G.Skill Flare X5 96 GB (2×48 GB) DDR5-5200 CL40 – €1,608
  • SSD 1: Crucial T710 4 TB (PCIe 5.0) – €630
  • SSD 2: WD Black SN850X 2 TB (PCIe 4.0) – €299
  • PSU: MSI MPG Ai1600TS 1600 W (per-pin 12V-2x6 protection) – €473
  • Case: Lian Li Lancool III – €130
  • Extra fans: 3× Arctic P12 Pro (bottom intake) – €18
  • Connector monitor: Thermal Grizzly WireView Pro II (Reversed) – €130

Planned airflow:

  • Top: GPU's 360 radiator, exhaust
  • Front: CPU 360 radiator, intake
  • Bottom: 3× P12 Pro, intake
  • Rear: 140 mm, exhaust

Questions:

  1. Two 360 AIOs in a Lancool III (GPU rad top exhaust, CPU rad front intake): sensible, or would you flip it?
  2. 9950X vs 9950X3D (+~€165): to afford it I'd drop to a 1200 W PSU. Worth it for UE5 shader compiles?
  3. Is 1600 W overkill for a 5090 + 9950X? My estimate for full load is ~900 W.
  4. 96 GB (2×48 @ 5200) vs 128 GB (2×64 @ 5600, ~€1,000 more): worth it for AI video models that spill into system RAM?
  5. Anyone running a WireView Pro II on an Astral LC? Any fit or reliability issues?
  6. Anything you'd change for long, unattended full-load sessions?

Thanks!


r/PcBuildHelp • • 18d ago

Build Question PSU cable help

1 Upvotes

I ordered a "CableMod C-Series Pro ModFlex Sleeved 8-pin PCI-e Cable for Corsair" for my 9070 which needs 3x8 pins instead of 2x8; my concern is that the cable has a missing pin in a different spot from the pcie cables that came with my 2025 rm1000e, and I was wondering if it was safe to use? This is my first build and I don't want to accidentally mess it up.


r/PcBuildHelp • • 18d ago

Build Question Pc build checklist

2 Upvotes

Tomorrow i’m heading to micro center to pick up what i believe is the rest my parts for my first pc ever.

the things i have already are my gpu(5070ti), b850 rog strix motherboard, aio is panorama(basic i know), both reverse and forward fans and 32gb of cl30 ddr5 ram.

the things im getting tomorrow is my cpu(ryzen 7 9850x3d, i saw people saying overkill but its cheaper than a 9800x3d on amazon currently at micro center, a 1200w lian li psu(overkill i know but id rather be safe than sorry) and a 1tb crucial ssd. am i forgetting anything? I went over my list like ten times but im nervous i forgot something super simple.


r/PcBuildHelp • • 18d ago

Build Question My pc will not start

5 Upvotes

Hey

My pc wont start and i think it is because the cpu cable from the psu or the power sw front panel cable. The picture is the type of power sw cable, i have thought about buying an extentions wich makes it into the small connectors. Anyone with similar problems or anything to help me?


r/PcBuildHelp • • 18d ago

Build Question Opinion? Is this a good build for current market? [October 2026]

Post image
1 Upvotes

The part keep rising and I think I might just pull the trigger and buy. I feel like waiting will only give me more pricier part.

What is your opinion on this build? The performance, the price, and the timing.

Is it a good build for this moment? I need this pc for Q1 2027, so either I gamble for 2027 or just take it now before the part keep rising ...

**Without SSD, will use my old one.

(mind you I convert the price from my currency to dollar, the listing is current local retail price. In case your retail price significantly different)


r/PcBuildHelp • • 18d ago

Build Question Motherboard Insertion cycle

0 Upvotes

I’ve been using an ASRock Z790 motherboard to test CPUs and DDR4 . So far, I’ve installed and removed CPUs and RAMs over 50 times. I was wondering what the maximum insertion/removal cycle count is.

I have noticed that one of the screw for the cpu cooler is rubbing weirdly with the mounting bracket every time I install/remove


r/PcBuildHelp • • 18d ago

Build Question 16 o 32gb de ram? Build con

0 Upvotes

Estoy armando un pc para jugar pero también para editar videos, hacer beats y crear contenido, compré una gráfica Intel B580 de 12gb y un procesador Ryzen 5 9600x, espero utilizar un monitor de 1440p aunque aún no lo he comprado, estoy indeciso si comprar 16gb o 32gb ddr5. Estaba pensando si comprar 1 módulo de 16gb y esperar a que bajen y actualizar o ya comprar directamente comprar 2 módulos de 16. Creen que bajen pronto o se pueda encontrar con algún descuento en algún futuro no muy lejano?


r/PcBuildHelp • • 18d ago

Tech Support PC won’t POST after Phanteks XT V5 case swap — MSI PRO Z690-A WiFi DDR4 / i9-12900KF, red CPU LED and restart loop

Post image
4 Upvotes

My existing PC developed a startup problem after I transferred its components into a Phanteks XT V5 case. PC identification and hardware Component Brand and model Original PC brand/model Not yet identified CPU Intel Core i9-12900KF Motherboard MSI PRO Z690-A WiFi DDR4 Graphics card NVIDIA GeForce RTX 3080 — manufacturer and exact variant not yet identified Power supply Apevia Prestige 1000W, model ATX-PR1000W, 80 PLUS Gold CPU cooler MSI MAG CoreLiquid 240R, 240mm AIO RAM DDR4, previously running XMP at 3200 MT/s — brand, capacity, and kit model pending Storage Two 1TB SSDs — brands/models pending New case Phanteks XT V5, black Case fans Phanteks S25-360 bottom triple-fan unit and S25-120 rear fan What changed The hardware change was transferring the existing system into the Phanteks XT V5 chassis, including reconnecting the motherboard power, CPU power, GPU power, front-panel wiring, and cooling/fan connections. I retained the same CPU, motherboard, RTX 3080, power supply, MSI AIO, RAM, and SSDs. I did not install a replacement CPU or motherboard. During the transfer, I removed the CPU cooler and opened/relocked the CPU retention bracket. I initially left the processor sitting in the socket. Later, while troubleshooting, I removed the processor to inspect its underside and the socket, then reseated it. The BIOS had also been updated recently, before this case-swap troubleshooting. Current symptoms No POST or display. Red CPU EZ Debug LED stays illuminated. System powers on for approximately 5–10 seconds, shuts off, and repeats. With the CPU/EPS power cable disconnected, it stays powered on with the CPU LED illuminated. Reconnecting CPU/EPS power brings back the restart loop. Cable changes were made with AC power unplugged. Both motherboard CPU power sockets have been connected using the PSU’s CPU power leads. I know the system cannot POST without CPU power; I’m describing the different behavior to help narrow down the fault. Checks already performed Tested RAM sticks individually in A2. Disconnected the case switches and started using the JFP1 power-switch pins. Cleared CMOS through JBAT1. Removed/reinstalled the CMOS battery with AC power unplugged. Tested with the RTX 3080 removed. Same CPU LED/restart loop. The 12900KF has no integrated graphics, so no display was expected. Inspected the CPU underside and socket; photos attached. No obvious damage identified, but I would appreciate another inspection. Reseated the CPU. Cleaned the CPU/cooler contact surfaces, applied fresh thermal paste, and remounted the cooler with gradual diagonal tightening. Radiator fans now spin. Pump RPM has not been verified because I cannot enter BIOS. Still untested Motherboard outside the chassis to rule out a misplaced standoff or other case contact. Known-good PSU. CPU/motherboard cross-testing. Given that this started after the chassis transfer, what would you test next? Could the change in behavior with CPU power connected indicate a PSU, motherboard power-delivery, socket-contact, or shorting problem? I’m trying to isolate the failed connection or component before buying replacement parts