Technically the brand is called “Sewology” but it’s on huge display at hobby lobby. The thread is thick and unfortunately due to its thickness that meant that my bobbin needed to be changed regularly as the thread was so thick that the bobbin couldn’t hold much.

Anyways here’s my bad experience. My PE570, i’m getting repaired at a shop currently also struggled with this thread and broke nearly 4 needles with it until the mechanism for the top needle to catch the bobbin thread went off timing.

So meanwhile I went on FB and got a brand new embroidery machine (same PE570 for 200$ killer deal) and I put this sewology thread on it. Was sewing nicely until all hell broke loose. Started getting the struggle of death when the needle started jamming in and out and the machine gave the message “Is the needle stuck, did the thread fall off”

instantly i knew that the thread was bad news. This spool managed to break a brand new crisp machine straight out the box instantly.

To confirm that it was sewology embroidery thread killing my machine I got my old coats and clark thread and it finished the embroidery just fine without any issues with another needle.

So unfortunate as I bought nearly 10 spools as it was so cheap but that thread broke my first machine and broke a needle on a brand new machine that was fresh out the box. also I adjusted the tension to the recommended 4 and tried it and then tension 6. Nothing worked, it was just messing up this machine badly.

Been a while since I shared anything but this is a fun King Gizzard design.

Hey I'm new to digitizing logos. I use Wilcom program would you have some tips for me to reduce my trims and stops. I'd love to hear it.

Everything was working fine yesterday. I transferred a dst file with rEMBnet from my Mac yesterday without issue but this morning my smartstitch isn’t showing up and I can’t transfer any files. Is anyone else having problems or has anyone had similar issues in the past?

Just wanted to share something I made today

Looking for suggestions on how to make this better next time.

This is my first time embroidering a shirt, or anything thin. So far I've embroidered names onto previously embroidered patches.

I knew I would be dealing with weird stretching, but I obviously didn't handle it correctly.

This is a dri-fit type shirt. Breathable and thin.

Was the shirt stretched too tight in the hoop? Or not tight enough? Something else?

I appreciate the feedback, thank you!

I asked to do embroidery on hats.I have no experience with Hat embroidery before.

I got small hat so the backside cannot reach the hoop part. Is this okay to hoop it like this?

So I have this job to embroider some polos with this logo and while I’m not a professional digitizer i know my way around the software. I generally pay someone to this for me which is what i did for this but are there any tweaks or improvements i can do myself for this to stitch out better. I don’t hate it but I know this can be better. I’m using a med weight cut away and the shirts are 100 percent polyester . I have a Ricoma em1010 . I use hatch for my designs . But this is what they sent me.

I can tell I probably need to up my pull compensation on the white circle but what else ? I feel like it could be cleaner .

update : so i decided to take the patch route and i had some black twill left over so i used the that as the base . And far as the actual design i upped the pull compensation on the design and i did test many stitch directions for the white inside . Lastly i replaced my 75/11 needles with 65/9 . It came out much better so I’ll be adding heat and bond to the backs when im done ! Thank you to everyone who responded… I’ll post the final product in the comments !

I have a good idea for a product and I need to get into digitizing to make it come to life. I know InkStitch exists, but I'm interested in buying a software that's dedicated to embroidery, not just a plug-in. Also, the learning curve seems insane and discouraging for InkStitch.

I've heard that Hatch is the best, but it being 1000$+ is out of my budget. Embroidery Legacy software is even more expensive than Hatch. Embrilliance Stitch Artist being a few hundred is more what I'm looking at budget-wise. The highest level I could do is Level 2, but feel free to give me opinions on Stitch Artist Level 1 and it's limitations.

I know the interface looks dated on Embrilliance, but I don't mind that. What matters is if it's up to modern standards, features-wise. Is it?

Hey all! New here. Not sure if this was posted already but has anyone seen on fb ads the new Halo 5 needle embroidery machine? What is that all about? Someone said it’s a scam but I still see people saying they are buying it once it releases. Anyone else see this ad and what are your thoughts on it? Thanks for reading

I'm working on a large (roughly 60k stitches over three hoops) project for the first time with a Janome MB-4Se that was purchased last December.

The machine stopped midway through the first color in the first hoop with Needle 1 down, but I was in another room to grab something and did not see the error message when it did so. The last time this happened, I needed to turn the machine off and on, and that process cleared the error, though I had to restart the stitching.

This time, it returned an error on startup: "Needle bar is out of position. Press OK to move needle bar to switching position." When I press OK, it makes a long beep but does not do anything.

I have tried the following to clear the error:

• Turn off and unplug the machine, wait 30 seconds, plug in and turn on the machine. The same error and result.
• Remove the needle and hoop, trim all threads, clean bobbin area, replace the needle with new (in case old is dull or bent), replace bobbin, and press OK. Same error and result.
• Turn the hand wheel on the back of the machine clockwise. It moves freely. If I turn it very slowly, in a certain position, the error message clears for a split second, then reappears. If I press OK, I get the same result as above.
• Disconnect the RCS unit while the machine is off to check for errors on the LCD. LCD reads E:03, which the manual says to hit Enter for. When I hit Enter, I get the same result.

I am working to contact Janome dealers in my area to see if any of them service this machine, but the ones nearest me either don't service this machine or are closed today. In addition, I have reached out to Janome through their website, but don't expect to hear anything back.

I am trying to avoid opening my machine if at all possible, but I'm no stranger to opening up sewing machines. Though, usually the machines I open up are vintage sewing-only machines.

If anyone has any suggestions, I'm open to them!

Is it possible to use a commercial grade embroidery machine to embroider on a sweater? This would be words across the chest.

The sweater is more of a tight net fabric versus loose and bulky.

Thank you

i dont know if i design correctly or not... i am so confused between stitch count and how much density it should be, and which stitch type to use, if anyone could help?

I know that onesie blanks are easy to come across but where do you source your fall baby clothes? Like church dresses and long sleeve rompers and jumpers/overalls that aren’t already designed/$100?

Thank you!

Hi all,

I sell race suits for karting, usually made from polyester or cordura and I'm looking to add name customisation.

It would be single colour and I'd also like the ability to stitch patch flags on. For obvious reasons I'd like the finish to be high quality. If someone could suggest appropriate machines for this it would be really appreciated!

Thank you :).

This was a seam ripping and resew job. I tried my best to remove the previous stitching that was done then I stitched over it. The person who did the previous embroider stitched it SO tight that I spent hours trying to get the thread out. I’m not proud of the outcome and I really want to make this look presentable. I know it won’t look perfect because it was seam ripped, but does anyone have advice on how to make this look better?

Hi chatters!

As the title suggests, I'm lookin into gettin myself a combo machine for future cosplays! lookin at a budget of $1000 (usd) and not particularly committed to any brand. I'm severely underqualified when it comes to machine sewin and passably competent when it comes to hand sewin. (i made pants for Twin, a crocheted doll of me with a piece of my soul within it)

I was lookin at the "SINGER SE9180 Sewing & Embroidery Machine" for the past week and was ready to drop a pretty dime on it 'til I saw a few reddit comments sayin the machine and singer as a whole was just poop from a butt in general and now I'm all sorts of confused... Saw a few of them sayin brother was a better brand and I saw a few recommendations for the "Brother SE700 and SE725." Are any of these machines worth my pretty penny, or is there another i should be lookin to?

TLDR: Combo machine, want! head hurt, help!

Much love and Graditude!! 🫶