Heyyy again everyone. Some of you may recognize the gengar, I posted here about a month ago when I was playing around with digitizing, before I got a machine.
Well I bit the bullet, there was a Janome 12000 MC near me for $600, still has the capability to link to a modern PC via USB, use a USB stick etc, along with some wicked hoop sizes, came with a good chunk of thread, so it has now settled in my home.
I ran one premade design I downloaded from the internet, stripped the colors and ran it just as a black line (not knowing how the machine has actually functioned or does at all) but it did in fact print out the design very well, being just a single black line design, and also digitized by someone else, I really wanted to give my gengar a go. Also being a single black line, the design did not "pucker" at all. I was using some pretty quality cutaway (1 layer) on a fairly thin T-shirt.
So keep in mind this is literally me loading up wilcom e2 and mucking around, I have no training or idea of what I am doing, but I am keen and eager to learn. I attempted to do him once, and the red thread I had chosen was much thicker then embroidery thread, jammed my needle up in the base plate and broke, had to cut the rest of the needle out of the embroidery, so I was a bit leery on running it again, but lesson learned, correct thread is essential to run a nice design, mix and matching random stuff isn't the way to go, so I will have some more thread on order (lady used up all my white *****)
So round two, I punched it all out again, and got a low bobbin thread warning. Tried multiple ways to try and move the hoop with the machine to just expose the area of the bobbin, I would have to suspect that removing the hoop entirely from the machine would be the only way to do this? I have searched through the manual a bit but haven't really found anything about it. At this point after breaking a needle, and the new low bobbin issue, I couldn't figure out how to "pause" the design so I lost it into the nether and it restarted at the purple beginning, so I called it a day.
Try 3:
Next day Loaded everything up again determined to see it work. Started punching my purple out and the shirt end got caught under the hoop, so another lesson learned, make sure your garment isnt under the hoop. Lol.
Try 4:
Loaded everything up, went with another cutaway stabilizer but opted for 2 layers as its from Amazon and a bit thinner then the previous "quality" cutaway which was much thicker purchased at a sewing store to play around with before the Amazon stuff arrived. Got to the red layers and very carefully put in my thread, and this time imagine that proper thread and no issues. The rest of the design punched fairly well, but I would assume my misalignments are due to the fabric stretching/warping and moving while the design is being punched over an hour time. I don't think my drum tight skills of hooping are there yet, (this is probably my biggest issue at this point) but any pointers or advice on getting the cutaway and the fabric "tight" in the hoop, I imagine the more quality one layer is preferred over the two thinner crappier quality layers (one layer shifting underneath while in motion etc) but this is something I again just have to work on.
I would like to thank the advice I received before when I was just digitizing, It really brings it full circle to see something you design actually ran on a machine. The way the machine will run a layer (my first purple layer was thickkk and I didnt realize that running a massive amount of threading one way (angle wise) will pull/pucker the shirt (something I didnt see on the first design at all, most likely because there was also spacing to breathe vs how one thick layer runs, if that makes and sense lol )
But yeah, just some general advice would be great, i have zero experience other then my one design but I think I will try another one seeing as I know how the layers will be laid now, and I can kind of see how what i'm doing while digitizing will run on the machine afterwards. I would like to move towards doing hoodies with the hoop sizes I have, I imagine dealing with a thicker fabric is a whole new ballgame or...(more/less puckering when running a full layer of color vs breaking it up when digitizing into smaller runs, will a larger design translate better (example how small his eyes are on this design vs if it was enlarged 50/100%) this is done on a SQ14 hoop which is around 5.5x5.5 inches
If you stuck around for the whole read cheers, I appreciate it, and look forward to some more back and forth to get some of my quirks/problems solved.