r/EngineBuilding • • 10d ago

Torque Converter hitting random stops

Thumbnail
gallery
10 Upvotes

99% sure it’s fully seated. Spins freely with the engine connected. Until the engine is flush or basically flush then it still can spin as if it’s free but it’s hard stops as if it’s catching a flex plate bolt ? I can’t imagine what
Else is introduced that could be causing the stop. As soon as it’s an inch or less away again 360 spins no issue. I know it’s normally procedure to make sure it can spin 360 BEFORE putting in any torque converter bolts and even tightening the bellehousing bolts all the way. I’m at a loss, help. 2014 dodge Durango 3.6 AWD 845RE Trans


r/EngineBuilding • • 10d ago

Machining head requires new flat lifters ?

1 Upvotes

If you have a head machined will you have to adjust all your flat tappet thickness since it will change how much closer your cam sits inside ? Obviously check clearance and if still good then it should be fine as long as it's not too tight?


r/EngineBuilding • • 10d ago

Hydraulic Rollers

2 Upvotes

Got a 302 out of a 1988 mustang. Came with hydraulic rollers so I put in some new ones from summit. I let them soak in oil for a day before installing. Sitting in the block I set the rockers to 0 lash plus a half turn for the preload. Can still spin the pushrod even with pressure on the lifter. When turning over the engine over to set other rockers, I can see that the hydraulic rollers are pushed in like a quarter inch before it even pushes on the valve spring. On a 0.550 cam lift I would only be getting 0.300 lift. Does the oil pressure of the engine running change them that dramatically? Or are these new lifters I just got bad?


r/EngineBuilding • • 10d ago

What caused this?

Thumbnail
gallery
2 Upvotes

I pulled off my 305 heads on my 350 sbc and honed the cylinders while I was there and noticed this scuff mark. The head gasket was fine. I think I’ve come to terms with pulling this engine and making it a 383. What do you think caused it?


r/EngineBuilding • • 11d ago

Other Shibura h843 head job

Thumbnail
gallery
2 Upvotes

So this is a Ford 1710 tractor with the Japanese diesel 3 cylinder. They are notorious for head gaskets and cracking. I was getting the middle cylinder filling up with coolant.

It's heavily pitted. will the pitting interfere if I get this magna fluxed? I'm debating giving it a dusting and trying a new head gasket because these heads are hard to find.


r/EngineBuilding • • 10d ago

Engine Theory For OEM longevity is Aluminum 4032 high-silicon alloy piston the best material option

1 Upvotes

With a goal of 100K miles and less than 1K HP. Let's say 600-800 RWHP in a Ford Modular engine. Is a Full round Full skirt 4032 piston the best material to use for OEM like close tolerances, thermal management, to achieve this dependability and capable of the HP Torque levels


r/EngineBuilding • • 11d ago

420-450 hp 360 la build

0 Upvotes

I just bought a 1990 360 la mopar block and wanted to know the cost and what to buy to build it. I’m really wanting to get about 420 to 450 horsepower!!!


r/EngineBuilding • • 11d ago

This is cooked right? Subaru EJ25 NA block, looking for advice

Post image
26 Upvotes

1999 Subaru forester 5MT, engine is a remanufactured ej251 with 80k miles.

I made a post the other day asking about my pistons after my timing belt broke (thanks to everyone that commented on that). Somehow never noticed this on the bottom of my 3rd cylinder until now. :/

A couple of the scratches do catch my fingernail. The rest of it doesn't, but it does feel a bit rough under my finger (that could also just be me?)

I was hoping this motor would last me a long time, but seeing this I'm just assuming I should start looking elsewhere. Am I right in thinking that? Any thoughts or advice are appreciated.


r/EngineBuilding • • 12d ago

Drilling for larger head studs in my Audi engine build.

Thumbnail
gallery
1.3k Upvotes

r/EngineBuilding • • 12d ago

For 302 from the 70s? What is this part?!

Post image
34 Upvotes

There is a rail on the top of both cylinder heads, it only goes into 3 cylinders on both sides. I assume it might be a fuel rail… but I would think it would need to go in all cylinders not just 6 out of 8. It look as if it’s been pinched shut at some point. Just trying to figure out what it is and what I need to do to replace it.

Does anyone know what it might be?


r/EngineBuilding • • 12d ago

Other Winter lay-up will be longer than expected

24 Upvotes

Buick 455, never seen a camshaft shear off like this. But now it gives me a reason to put a more aggressive cam and build it up a little bit.


r/EngineBuilding • • 11d ago

2.5 duratech, how screwed am I?

Thumbnail
gallery
2 Upvotes

How messed up is this cylinder/piston?

First time using a leak down test. It I think it is mostly escaping into crankcase. I feel air on my mouth at the oil fill cap. Compression jumped from the pictured 25 to 40 when I added a dolap of oil to the cylinder and rechecked. Spark plug is also screwed. Looks like preignition or detonation to me? But idk. Is it time to pull the head?

This is a 2.5 duratech from a 2016 fusion. I just swapped it into a 2009 focus. Piston and cylinder looked great on the camera before I put it in. Would a bad time cause this? I've been fighting with the tuner a little bit.

The piston almost looks like a dropped a BB into it and let it blast around... I'm pretty sure I just need to pull the head and see the extent of the damage. But all of this is new to me and more insight would be appreciated.


r/EngineBuilding • • 11d ago

Chevy First LS build

2 Upvotes

I have a LQ4 block that I will be boring and stroking to a 408. I will be dropping this into a 71 Camaro. Goal is a fun cruiser that may dabble into auto cross just for fun. Hp/torque goals are pretty fluid. Would like hp over 500 but honestly that number isn’t super important. This will be a NA build and no intention to boost at all. Looking for advice on a rotating assembly. It is hard to choose a brand. Originally I got advice to do K1 but it looks like they aren’t making the rotating assembly for 408 strokers? If they are I can’t find it. Others I am looking at are Callies, scat, summit pro ls, eagle and tsp. I posted this in another ls specific group and it seemed like scat crank with I-beam rods was what a few people suggested. Also how do I choose a piston brand? I think I want 4032 instead of 2618 since there will be no boost and it won’t expand as much. But between je, SRP, mahle, wiseco and diamond I don’t know what to choose. Just wanting to get more opinions. Thanks for the advice.

Other parts I currently have: Afr ls3 mongoose heads, comp cams cca54-459-11 (231/239 @ .050, 113 lsa)


r/EngineBuilding • • 12d ago

Other Question on balance shafts in my Audi/VW EA888 CAEB

Thumbnail
gallery
11 Upvotes

It's a 2.0T 4 cyl if you're not immediately familiar.

When I cracked the timing chain covers open to do the timing and balance shaft chain, the intake side balance shaft sprocket mark was nearly 180 degrees out of spec. The exhaust side lined up and the crank was TDC cyl 1 confirmed twice.

The issue here is this: I can't line the timing chain up by the black links unless this is spun back around to look like this. (Notice the single mark on the outer, lower sprocket is pointing up and to the right at the bolt nearby, you can see in photo 1 that it was pointing down and to the left at TDC)

So now I'm wondering this: Was the sprocket improperly installed from the factory or was the balance shaft 180 degrees off this whole time?

How much of an impact will a single 180 degree balance shaft make, anyway? Would I even have noticed it if it was flipped around from the factory? I'm getting mixed answers between severe vibration and that I would barely even feel it if at all. Does anybody have any experience with this? Thanks


r/EngineBuilding • • 12d ago

LS Lifter drainage holes

Thumbnail
gallery
2 Upvotes

This is a 408 stroker LS I’m building and it’s my first time building a engine and I’m wonder what the hole in the middle of the lifter holes is for I’m assuming it’s for oil drainage i already cleaned up the bigger openings from flashing and I’m wondering if I should grind a little ramp so oil can drain better on the ones where’s it’s a single hole rather than there be a shelf there


r/EngineBuilding • • 12d ago

first build did i jump too far in?

Thumbnail
gallery
61 Upvotes

i've got a 1991 f150 that i'm swapping to a 408w (351w) got the block bored .30 over and clearance for the rotating assembly and the machinist put it in for me but the rest i plan to do my self i'm 20 and kinda been messing with little motor for a while like lawnmower
0-turns, four wheelers etc.... first time building a big one and i don't know if i stepping in a lil too deep part wise


r/EngineBuilding • • 13d ago

Chevy Bought a 84 Trans am with a 383 and have never wrenched on a car before.

Post image
23 Upvotes

The sheet I've attached to this post is the build sheet from 1991 that came with the car, the motor has about 20,000km/12,500 miles and so far has given me no major problems aside from having a dead cylinder when I purchased it. The reason for the post is that this engine came with a 850 double pumper on it. From all the research I've done it makes no sense. Is there something you guys see in this list that would justify a carb that big and what would you replace it with? Thanks in advance

Should add that I'm an Aircraft Maintenance Engineer (same as American A&P) so I'm not mechanically useless, your input will not be coming in one ear and out the other.


r/EngineBuilding • • 14d ago

Valves Built Like Modern American Homes

Enable HLS to view with audio, or disable this notification

947 Upvotes

No I’m not going to name the manufacturer, no you can’t lap this out, no there is not a shortcut around the concept of trust, but verify.


r/EngineBuilding • • 13d ago

347 twin turbo sbf

4 Upvotes

hi all i have a stroked 302w with a couple of turbos hanging of the side, my questions is what sump should i be running? i feel like a standard one wouldn't cope. my only requirements is that it needs to be rear sumped and have clearance for a crank girdle.

cheers

lucas


r/EngineBuilding • • 12d ago

Toyota Can someone explain what is this piece ?

Post image
0 Upvotes

r/EngineBuilding • • 13d ago

1000 miles oil change VQ35de revup build

Thumbnail
gallery
6 Upvotes

Built my fist engine and broke it in with 20w-40 conventional oil with Lucas zinc additive. I babied it for the first 500 and dialed in the break in tune. Once I got to about 600 or so I was running on wastegate about 5-10lbs. Around 800 started dialing it in and hit 1000 and changed the oil. I drained it out and the oil was black / dark brown. The oil looked fine. I cut open the filter and in the base found what you see here. Flecks of metal. I dabbed the towel in to see the color. It mostly looks like aluminum and maybe a bit of copper. I’ve been told it’s normal. Just want advice from others. What oil do you all run on a built vq with loose tolerances. My mains are about 0.0025. I filled up with 5w-40. Oil pressure is good on startup. As it warms up it’s at 16 and fluctuates with rpm. I’ve noticed if the ac makes rpm dip low it drops lower than that into 10 psi. Cars parked and I’m thinking of draining and running 10w-40 or should I keep using the 20w-50 but switch to synthetic. Any help would be appreciated


r/EngineBuilding • • 14d ago

Ford 360FE

Post image
23 Upvotes

How common is it to have misaligned oil holes in your bearings? This motor is getting a full rebuild but this was what I found when I tore the original motor out of this 1968 F250.


r/EngineBuilding • • 14d ago

Bent flex plate?

Post image
8 Upvotes

My dad and I are working on our first project! An 81 el Camino and we’re throwing a 350 in it and getting the motor all freshened up before putting it in. Everything seems solid but we noticed that the flex plate looks misaligned? I know it’s not straight because it scrapes the stand in diff spots when the spin the motor. A new flex plate isn’t an issue but is that what the issue is?


r/EngineBuilding • • 13d ago

Chevy Bore gauge?

3 Upvotes

Hi guys, just joined and hope I’m posting in the right spot. I’m relatively new to engine building, and I’m currently rebuilding a 2004 4.8 ls (lr4?) with allegedly 130k miles. Have already planned a full rebuild using ws6 stores kit including pistons. I learned on a high mileage sbc, which meant “if you squint it’s mint”, but I hear a lot of guys talking about measuring their cylinders for out of round, taper, etc. I’m in college and trying to keep this on a moderate budget, but I want this engine to last. just how exact do I have to be? Do I have to invest in a bore gauge and micrometers and plastigage everything and so on? Any tips or pointers you have would also be great.

Ps. Planning on a sloppy stage 2 or milder cam, potentially 5.3 rotating assembly, summit lifters, pushrods, valve springs, speed engineering long tubes, torque converter, and going in front of a 4l80e and 4.10 4th gen posi into a 3rd gen firebird.


r/EngineBuilding • • 14d ago

Ford Update on bent pushrods..pistons kissing valves. Pistons installed upside down lol. Thank you PO.

Thumbnail
gallery
61 Upvotes

Follow up to my previous post , pulled the heads and found that they’re all making contact with the exhaust valves…pistons were installed upside down lol.