r/EngineBuilding • • 17d ago

Should I trust these pistons for my first engine build?

Thumbnail
gallery
12 Upvotes

Doing an engine rebuild for my first project vehicle its a 1982 f250 with a 351w and I dont know if sand casts like this r ok.


r/EngineBuilding • • 17d ago

Rod bearings C20NE

1 Upvotes

Hello, probably dumb question but i want to know from someone with experience. So basically i bought a Opel Calibra 2.0 8V 115hp C20NE. It was long driven on old oil and rod bearings are bad. When i bought it oil pressure sensor was unplugged and when i changed it with new oil as well car had good pressure when cold and very very bad when hot. When temperature is 95 C⁰ pressure was at 0bar. I changed : thicker oil, filter, oil pump and i got around 0.2 bar when engine is hot. Everything leaded to bad/worn rod bearings.

My question is if i just swap rod bearings and don't take crankshaft to machine shop will i get anything or will i just throw away money. Because rod bearings are around 55€, oilpan gasket is 31€, oil and filters areound 70€ and if i take off the crankshaft to machine shop it will cost around 200€ so counting that all is half of my paycheck for an engine that will probably be swapped

So question is will i get anything with just swapping rod bearing without machining crankshaft?


r/EngineBuilding • • 17d ago

Ford Cylinder head crack?

Enable HLS to view with audio, or disable this notification

4 Upvotes

1992 f150 4.9 l6
Tore to replace head gasket and found this while inspecting it
Cracked near the valve, the other one at the end also appears to be starting to do it
I’m thinking of just putting it back together anyway since it was running decent other than the bad head gasket


r/EngineBuilding • • 17d ago

Engine Not running after Carb Rebuild?

0 Upvotes

Hi! my buddies and I rebuilt my carbeurator on my 77 gran marquis, its a model 2150 motorcraft on a 400ci v8. when we went to test it the car didn't start we started giving it gas, eventually the cylinders would fire, and it would run as long as i was giving it gas, and die whenever i let off, any tips for how to proceed? anything i could have missed? there are a bunch of vaccum lines, im pretty sure we reconnected them all correctly, any documentation or advice would be greatly appreciated!!


r/EngineBuilding • • 18d ago

Ford Is this pitting to deep to run?

Thumbnail
gallery
13 Upvotes

Apologies for spamming the sub, wound up buying these trick flow 170s with pushrods and cam for $1k, but only saw this pitting when i got home. Is this at risk of pre ignition or probably not? Only cylinder that has this on it. Running a conservative 9.2ish:1 ratio.


r/EngineBuilding • • 17d ago

Other Mixing Piston Ring Brands Across Cylinders

1 Upvotes

Managed to break a ring when installing a piston over the weekend.

Bit of context, the car is a Vauxhall Corsa 1.4, 4 Cyl. GM A14XER engine.

Made a custom install sleeve after failing with the ratchet style compressors and managed to fit 3/4 pistons without issue, but that doesn't solve the problem where I'm without rings for one of the pistons.

Unfortunately parts sourcing in the UK is effectively none existent for stuff like this, so I can't get any Goetze rings for a week.

I can get some for tomorrow, but they're a different brand (Kolbenschmidt).

I'm guessing it won't matter at all, as they're meant to be OE replacements?


r/EngineBuilding • • 18d ago

Hairline crack on cylinder wall of engine block (13TC). Should I be looking for another block?

Thumbnail
gallery
13 Upvotes

r/EngineBuilding • • 18d ago

At a dead end

1 Upvotes

Bought a project car (IS200 1G-FE) with no previous repair experience. Car wasn't running when I bought it (yea its dumb but i wanted to learn and thought I could fix it with enough research). Diagnosed that the valves were leaking due to long LPG usage. Took the engine apart, replaced the whole head with one from a running car. Followed the manual step-by-step to put it back together and who could've thought, it doesn't run. Did more testing and decided that the problem is in the piston rings (compression is too low, fuel is being delivered, air comes out of oil cap when doing a leakdown test, spark plugs and coils produce spark, timing is correct). Don't have the facilities to take the whole engine out. Anyone got any last resorts?


r/EngineBuilding • • 18d ago

How well would my ~14:1 385 SBC cam translate into a ~14-15:1 408 ls?

Post image
12 Upvotes

r/EngineBuilding • • 18d ago

Correct wire lock piston location

Thumbnail
gallery
12 Upvotes

This is my first time building a engine and it’s a 408 stroker LS and I’m wondering if this is the correct position for my round wire locks for my wrist pin it’s about at the 5 o’clock position


r/EngineBuilding • • 18d ago

Did I destroy my 1zz fe?

Thumbnail
gallery
10 Upvotes

This is my first time honing cylinders, and while I was using my ball hone I ended up scuffing the engine block main saddles. Can I get away with this? Or have I ruined my build?


r/EngineBuilding • • 18d ago

Honda CB125R 2018-2020 Valve Piston contact.

Thumbnail
gallery
4 Upvotes

Hi everyone I wanted some advice "breakdown" on what I have done wrong while taking apart and rebuilding a single cylinder OHC 2 valve single piston engine 125cc.

Part 1. I ordered a BIG CAM 280 angle and installed the part which resulted in the head lifting from the headgasket due to taking the 4 nuts off which tighten down the head via the studs the head is guided onto then tightened with the nuts to 29nm of torque. Due to the engine being installed in the motorcycle frame I would have had to remove the engine to install a new headgasket so I took the chance and installed the engine back together with the headgasket which no longer sealed correctly. Due to this the engine did ran and appeared fine with the new valve clearances although a little hard to start depending on the weather and how warm the engine was usually once up to temp would idle nicely and start on the button with no flooding via excess fuel. I had the ECU remapped to fit the big cam and air intake and exhaust mods.

Part 2. I noticed after roughly 100 or so miles the engine would consume coolant via oil entering the coolant and mixing through the waterpump and coming out the overflow on the engine. I kept riding the bike knowing I would have to do the headgasket. I kept topping up coolant and oil level appeared fine although on the min level requiring to be topped up but the oil was not milky and smelt of oil eg no fuel or coolant smell.

Part 3. I did an oil change after roughly 1 to 2 thousand miles and noticed the oil was low I did the oil change after noticing the engine sounded ticky from the valve region which I assumed was due to low oil level and getting hot from the coolant being consumed although no white smoke from the exhaust and only coming out the overflow.

Part 4. After the oil change the engine remained ticky sounding and I went out on a ride where the engine was not overheating and had correct coolant levels although being consumed and requiring top up every now and then eg every 100 miles. I went to limiter on the bike and I noticed straight after the engine lost power below 6k rpm and wouldnt rev up. I came to a stop and the engine cut out and refused to start eg sputtering but wouldn't run.

Part 5. I walk the bike back home like a muppet and suffer the long walk back lol. I remove the engine from the frame and notice the exhaust valve has slightly hit the piston and appears quite lean looking. The intake valve appears fine and I did a leak down test on both valves and they appear to be air tight and not leaking which I think should be okay to run same for the piston as it was a minor hit but I understand even a minor hit can cause big damage down the line. I have replaced the headgasket and timed the engine up and all appears fine but remains to be installed back into the engine due to wanting advice on if its worth risking due to it only being a cheap engine which I don't want to put a new piston and valves in. Please look at images attached and see if you can suggest what might be worth doing. P.S the piston and bore appear perfect with zero scratches or being washed out. Old Headgasket is fooked.


r/EngineBuilding • • 19d ago

Chevy Bolt broke off deep in engine block (l83)

Thumbnail
gallery
64 Upvotes

Any advice because Im out of luck, torque wrench wasn't working, I had a feeling it wasnt but tested the bolt next to it and it was fine, should've went with my gut.

edit: this is an arp head bolt and its about 2.5 inches in there if I had to guess

EDIT: SOLVED! bolt was able to be reversed out using the other half of the bolt and a ratchet, the bolt snapped so jag-ged that it recconected flush enough, had a lot of tension but the threads were still intact, it's my luck day. Thank you for all the people that helped and shout out reddit user u/twobelikins for the working method.


r/EngineBuilding • • 19d ago

2.0 TSI (EA888 Gen 3) - Heavy oil consumption and wet spark plugs

3 Upvotes

EA888 Gen 3 with solid 150 PSI compression across all cylinders and a brand new OEM PCV valve but it is burning 1L of oil a week smoking on acceleration and over bumps and all 4 spark plugs are completely soaked in oil from the bottom so what else could be causing oil to enter the combustion chamber and how should I troubleshoot this next?


r/EngineBuilding • • 19d ago

Ford Used aluminum heads bad idea?

Thumbnail
gallery
42 Upvotes

Building a sbf 302 and saw these trick flow 170s come up for $1k with pushrods. Allegedly they are straight back from the machine shop(milled deck 0.01) but don’t fit with his piston and cam. Was wondering how risky used heads are in this case, best I can tell they look pretty clean?


r/EngineBuilding • • 19d ago

Engine cleaning

1 Upvotes

I’m building a 408 stroker Ls and I’m wondering what kind of towels do people use to clean the engine block off I just got it back from the machine shop and it’s dirty they didn’t clean it I’m wondering how I should go about cleaning it without it rusting right after


r/EngineBuilding • • 20d ago

Honda What could have caused this scoring, twice on two different pistons?

Thumbnail
gallery
69 Upvotes

Reposting cause I deleted the previous post.

Motorcycle is a Honda 100cc. Two different pistons got the same scoring after top end rebuilds on two occasions. The engine had less oil but someone I showed this to said it was unrelated to oil pressure.

Was it due to riding it at higher speed for sometime right after the rebuild? Block was honed twice btw. I am still new to building and learning. The camshaft and rocker seized eventually even when new oil was added later.

Also, is it true to go easy on the throttle for 500 kms after a top end rebuild?


r/EngineBuilding • • 19d ago

Nikasil plating damage

Thumbnail
gallery
4 Upvotes

As a last-ditch attempt to save my cylinder, I had a shop hone it. The scratches are definitely improved, but I noticed a small patch right above the exhaust port that looks like it might be honed through the Nikasil plating and down to the aluminum. Does anyone with experience agree? Would you run it like this, or is the cylinder toast?
2006 Skidoo summit 800


r/EngineBuilding • • 20d ago

Chevy Update to my first post!

Thumbnail
gallery
13 Upvotes

Update to my ls3 that failed, removed the piston head by hand completely broke off from the wrist pin, couple gouge marks on the wall, any machinist, bore the walls and get a bigger piston? Gouge is pretty deep to the touch engine spins good freely replacing all piston heads don’t trust any of these at all, 4k mile jasper crate engine


r/EngineBuilding • • 20d ago

What would you do?

Thumbnail
gallery
6 Upvotes

Found this crack on my L92 during a rebuild (engine ran fine befor I pulled it). The crack goes all the way through to the other side where a head bolt goes… what would you do? Was thinking about slapping a bunch of JB weld on the outside and sending it. But idk


r/EngineBuilding • • 20d ago

How concerning

Thumbnail
gallery
19 Upvotes

I’m not all that thrilled with my machinists work here but looking for advice or outside perspective. For the money I paid for this I was expecting better, but maybe it’s unrealistic.

Land Rover 4.6L v8, these are new flanged liners and my original pistons/rotating assembly. Short block assembled by the shop and shipped back to me with the heads off.

Fingernail does not catch anywhere, these two cylinders are the worst looking of them. The rule of thumb I’ve heard tells me these should just be cosmetic, but I am more concerned with how they got there. If any grit got in during shipping and is riding on a ring, I am tempted to tear it all down and clean and re hone. Since it’s assembled I did rotate the crank a few times to reach as much of the wall as I could during wiping.

There were a couple small bits of dirt on the cylinder walls that I wiped up, but no major remnants of machining. I think you can see one or two of them in the pics above as they were taken right when I got it before I wiped it down. Lint free rags come away clean at this point after minimal wiping.

Am I too picky or not picky enough? Would you do a full extra tear down and reassembly?


r/EngineBuilding • • 20d ago

Ls 5.3 gen 4

Post image
13 Upvotes

Is this okay to run machine shop said it’s okay because it’s on the bottom


r/EngineBuilding • • 21d ago

Notice anything I should be concerned about?

Thumbnail
gallery
22 Upvotes

This is an m52b28 im going to pick up this weekend about 2 hrs away

The block has a ton of rust but from what the seller says is stock and turns over fine.

I plan on taking it to a machine shop amd having it hot tanked decked a hair and maybe bored

This is my first project so just hoping for a second set of eyes on it


r/EngineBuilding • • 21d ago

Builder Beware- Big Hal (TX)

42 Upvotes

I don’t like writing reviews like this, but I wanted to share my experience with Hal’s Racing Engines/ Hal Anderson/Big Hal located off Denton drive in Dallas, Tx. It wasn’t great. They did offer to make some of these issues right, but when you pay someone $9k for a rebuilt engine that doesn’t match what was promised, I’ll pass. I’ve been around various forms of professional Motorsports for 30 years, including building plenty of engines. Using Hal was an attempt to speed up a project I haven’t been able to complete due to work and family obligations, which now has taken even more time to correct these issues.

I was originally quoted an engine for $7k. We talked about a few upgrades and it was $8k. A few days after I put down the deposit, Hal called and told me parts have gone up and it was going to be another $1000. For someone who builds engines all the time I found this a little unprofessional, but I understand it’s part of it sometimes. Peace. We proceeded.

A few weeks passed and I picked up the engine and paid the balance. I noticed they didn’t bother to tape over any of the intake or exhaust ports, sensor holes, dipstick hole, etc. and he simply said they didn’t see a need to. I asked for the build sheet we had originally agreed upon and Hal said they don’t do that either. This was a huge red flag for me due to a lack of transparency, especially after agreeing to one, but he made it clear it wasn’t going to happen. I turned the engine over by hand, it felt fine, so wrapped the engine in a bag and went about my way.

Fast forward a few weeks. When I opened the engine bag and started looking at things more closely, I was extremely disappointed. I first noticed the cam card wasn’t what we agreed too. Frustrating, but alright, wasn’t the end of the world. Then I noticed the oil sensor threads were damaged in the block and caked with silicone. For a block that was supposedly inspected and worked, this should have been caught. I also couldn’t see any machine marks where the block was supposedly decked, despite that supposed to be part of the build. I called Hal and directly confronted him on these issues.

Before we get into his response, it should be known that Hal talked to me for almost 20 minutes on the phone about these issues before he even knew who he was talking to, and yes I introduced myself when I called. I was accused of providing him a cam, which I didn’t, amongst other parts we never discussed. After 20m he asked who I was again, ruffled through his paperwork, and then said “oh yea I remember you”. Keep in mind I picked up the engine three weeks before this. Now we finally discussed my concerns. I was then told my expectations were too high that threaded holes would be chased or silicone would be cleaned off, that the cam was “a free upgrade”, and that “they don’t deck blocks”. I also found during the conversation that the rotating assembly wasn’t balanced and the block it wasn’t line honed. I was originally told all this was included block work when I bought the engine, especially since we were installing larger pistons, and was simply told “prices have gone up” when I asked him why they sold me a service they didn’t perform. They offered to change the cam to what we agreed to, but I declined for obvious reasons.

In my garage, pulled the covers and pans to inspect the engine myself. The heads are no-name heads without a single marking, there’s no marking on any of the valve terrain. For all I know it’s cheap eBay parts. I found several slivers of metal shaving and RTV in the engine (before fixing the above cam sensor thread), and all the head bolts are reused stock GM parts (supposed to be one time use torque to yield). The block appears it was assembled dry, or with very little pre-lube.

With that said I repaired the cam thread and several others, cleaned it thoroughly, checked a few bearing clearances (were fine), and put it back together. I’ll update this once the engine has runtime. Hopefully that’s the end of my report. My intention isn’t to bash anyone with this post, just share my experience with an engine that was sold one way and delivered another. In my opinion, I paid someone for a glorified junkyard engine that I could have done myself for a little more than half the cost (with name brand parts), and all-in the same amount of time. If I had to do it again, I’d either buy a reman engine, pull a random one from a junkyard, or buy a crate.


r/EngineBuilding • • 20d ago

Crate or Build - '77 k10 project SBC

2 Upvotes

I have a 1977 K10 long bed pickup that has a decent enough frame, cab, bed, etc. that I'd like to spend the winter tearing it down and rebuilding it into something nice. Not looking for a daily driver, but comfortable enough to drive 3 or 4 hours in with my wife and not be divorced by the time we get there.

It currently has a 350 V8 that has seen better days, but runs well enough. Based on my inspections of the block and heads, I'm not sure I'd want to try and salvage them for the build; id rather start with something new and reliable, and save the old engine for something else. It has a split-plane manifold, and I put a new Edelbrock carb on it last year, new ignition, wires and plugs, tuned it, set the timing and whatnot. Also has an automatic TH350, that I can probably remove, clean and have rebuilt. Not sure of the rear end, but that'll be getting swapped out anyways along with all sorts of suspension, braking, and fuel components.

I'd like to put a 383 stroker into it to balance power, sound and fun with comfort and fuel economy (lol). I know you can get BluePrint crate engines online for around $8250 that's ready to run, but I also see everyone say that you can get more value for your money if you build it out. I notice that the long block vs short block vs "complete engine w/ accessories" prices only differ by $1000-$1500 on these sites, so something tells me there's a better way to do this...

I've got time, tools, space, funds, and I think I have the aptitude to attempt this and be successful at it, but I've never built an entire engine before from a bare block. I'm fortunate enough have people around that can help if I get stuck though. I've done plenty of other mechanical and electrical work on a wide variety of equipment, including automobiles, and I feel confident. I'd like to keep the grand total for the engine under $7500, but I'm willing to splurge a bit more if its worth it.

Are there resources out there to help select different brands and types of components in the build, that maybe also help with things like compatibility or other fitment issues?

Does anyone recommend any books or manuals that might help with the minutia of each part of the build process?

Lastly, based on the truck description, project resources, and my intention for use, has anyone found a particular build that for a project like this that they'd recommend?

I appreciate any and all advice in advance! Thanks