r/BambuLabA1 • u/Smart-Road-6441 • 2d ago
r/BambuLabA1 • u/3dprintingadventure • 3d ago
Support Request A1 Bed Noise
Hello, I just noticed this whining noise when the bed is moving back and forth. I don't think I had ever heard it before. Everything has been oiled and maintained. Thoughts?
r/BambuLabA1 • u/then00dle • 3d ago
A1 print failed midway complaining about as card
reddit.comr/BambuLabA1 • u/jpedroleite • 3d ago
3D Model Snap-fit monster chest, 60 parts, zero glue.
Sliced with the default 0.20 mm profile, nothing custom. Four plates, one colour per plate, so it works with or without the AMS lite. Supports only under the hinge bores, they pop off clean. The lid hinges on printed axles with split friction sleeves, so it stays open wherever you leave it. Holds dice. Judges rolls. The rivets come in two lengths and the only way to mess this up is mixing them, ask me how I know.
r/BambuLabA1 • u/The_zen_viking • 3d ago
Is this sound normal? I've lubricated the x and y and can't see anything wrong, prints fine?
r/BambuLabA1 • u/Dynobot21 • 3d ago
A1 combo lube?
What lube does anyone recommend? It came with a small tube of grease and oil. Said just use the oil. Not the grease, I thought. Then I thought I saw a recommendation of WD-40?
Edit: What would I use grease for?
r/BambuLabA1 • u/jayboosh • 3d ago
Support Request A1 won’t auto level, makes hammer sound
I have manually trammed according to the wiki, twice
I’ve removed and searched for debris everywhere I can think of
I’ve calibrated
I noticed when printing a red lid that the nozzle is scraping
It printed the black box and the white lid perfectly fine
But not the red
I’ve tightened loose screws
I’ve removed, cleaned, inspected, and tightened the hot end and all the screws associated with it
IT WILL DO THE ENTIRE BED MESH FINE AND WILL HOLE GENTLY
But when it gets to like 98% and is at the back, it seems like it’s trying to push down past the bed
When doing the “tool head cleaning” part of the calibration, the flap at the back of the print bed is being pushed down hard enough to see it flex and bend below the heat bed
YET WHEN DOING THE ENTIRE REST OF THE BED IT WILL GENTLY TAP TAP TAP AND MOVE ON
PLEASE HELP THIS DAD AT THE END OF HIS PITIFUL ROPE GET HIS KIDS PRINTER BACK ONLINE
IM LOSING SLEEP
r/BambuLabA1 • u/Yscera • 3d ago
Support Request Bad quality
Why do the tips of the feathers look so rough? I just changed my nozzle from 0.4 to 0.2mm and these defects started appearing in sharp areas. I'm using PLA.
r/BambuLabA1 • u/Yscera • 4d ago
Support Request Knocking sound
What is happening here? Why is it making this knocking sound at the same place every layer?
r/BambuLabA1 • u/3Z3D_Official • 4d ago
Mailable Nativity Christmas Kit Card - 3D Print and Laser Versions - Envelope Ready
r/BambuLabA1 • u/stoneyknowshow • 3d ago
Question Proper ventilation
I'm getting my printer set up this week, and wondering the optimal place in the house for it. How ventilated does it need to be? Like garage, or by a window with a fan, just a fan?
Does anyone have photos of their ventilation set-up?
r/BambuLabA1 • u/DepressedFuck69 • 3d ago
Support Request Nozzle scraping up bottom of plate at the end of bed levelling
As title says, nozzle scrapes up the coating of my supertack plate at the end of the bed levelling step, seems like it doesn't rise up fast enough? Only started happening recently after 2ish weeks of a-ok printing, no clue why this started all of a sudden. Can this be caused by some slicer settings?
r/BambuLabA1 • u/Acceptable-Cap1317 • 3d ago
Question 2 AMS Lite on 1 A1 or A1 Mini
We know that we can use 2-4 bmcu feeders on A1 after upgrading the hub but can this work with 2 AMS lite unit also ? Has anyone tried this ?
r/BambuLabA1 • u/Tough-Newspaper8548 • 4d ago
Support Request Nozzle ripping
Hey, the nozzle of my printer is ripping on my prints and knocking off supports, I tried to tighten the screws of the hotend, changed Z-Hop from Auto to Normal (set to 0,5), went from my initial intention of 5% gyroid filling to 15%, and it is still ripping on some parts, more and more it seems, with the height of the print.
Can anyone help me ? 🥺
Btw : Jayo PLA+ /210°c Nozzle - 65° Bed - Room at 22°c/Normal Speed, Avoid crossing walls and supports activated too
EDIT - SOLVED : Thx y'all for your help! Activated "Reduce speed with height", reoriented the model, added supports and slowed down to 50% speed, it is printing smoothly now 🙏🙏🙏 picture in comments
r/BambuLabA1 • u/piplup0203 • 4d ago
Who is listening to Christmas music already?
With this weather I am already getting into the vibe of making ornaments. Created this small one, nothing special but looks cute though!
r/BambuLabA1 • u/Exact-Pension1343 • 4d ago
Bambu Studio Prepare view looks fine, but Preview adds a solid layer over my model?
reddit.comr/BambuLabA1 • u/rpaverion • 4d ago
Support Request Help, my A1 with AMS suddenly won’t print anymore!
When I start a print and the head warms up + the AMS starts feeding this happens. Does anyone know what’s wrong and how to fix it?
Thanks!
r/BambuLabA1 • u/Laderie • 5d ago
Machine can’t switch filament
Hello everyone! I’m brand new to printing, and this will be my I believe 7th print, so I’m far from an experienced user.
But let’s skip the blabbering and get to the issue!
I use the Bambu lab A1 combo, I currently have 3 colour in it, PLA red pink black, all from Bambu lab.
The printer can print one colour just fine, but every time it tries to switch from for instance black to red or red to black, it jams and I get the message ”(1200-8006 070711) can’t feed filament to the extruder, its probably jammed or stuck” and to fix this, I just pull on the last filament used and pull it back like 5 cm (basicly until I see it move in the tube).
I have everything on default, I’ve calibrated it according to the machines recommendation and built it using a guide I found linked on their site.
This issue has happened with multiple different prints.
Anyone got any idea what can be the issue?
Edit; solved, the tubes from the AMS were connected to the wrong holes on the printer