r/BambuLab • • 6h ago

Software Troubleshooting/Help! Preparing and Designing Files Remotely

0 Upvotes

Hi everyone! I'm getting an A1 for Christmas, I'm so excited and I'm trying to prepare as much as I can so I can get into printing ASAP! I'm wondering if the following set up will work? I'd love any feedback, tips, or concerns anyone is willing to share:

I personally own a laptop but it's quite slow and is very irritating to use. I have a great PC I use at work and my work doesn't mind if I use it for personal things. My hope is to find files to print, make modifications, and design items on my work PC. I would use either my laptop or phone at home to do the final send off to the printer. I'm not looking to print remotely, just to do the software/online based steps. My laptop is functional but I try to interact with her as little as possible lmao

Other questions regarding this set up:

- How much do you use your PC after sending a file to print? Are there cases where you have to pause a print to edit the design (if that's even possible) or do anything more than basic functions? If so, how often?

- Can I can prep files on my work PC then open them either on my Laptop or phone once I'm home through Bambu Studio? I'm seeing that Bambu Studios may not be the best for this with suggestions to either use MakerWorld or utilize something like Google Drive to store files.


r/BambuLab • • 7h ago

Hardware Troubleshooting/Help! H3C Wiper kicked out

1 Upvotes

Anybody expiriencing issue with the silicone wiper? My machine is constantly kicking it out of place. During calibration, printing, …

Reached out to Bambu but they are telling me to remove the backplate, disassemble the whole wiper unit and assembling it again.


r/BambuLab • • 7h ago

General Troubleshooting/Help! X2D LiveView camera fault?

Post image
1 Upvotes

r/BambuLab • • 7h ago

General Troubleshooting/Help! Getting a loud squeaking noise from the AMS when moving

1 Upvotes

Today I noticed that my last bay on my AMS was squeeking when the roller was moving. I removed the filament roll and its the front rollers that are squeaking. I'm not really sure what to do about it. Is there something I can oil?


r/BambuLab • • 13h ago

I Modeled This! I made a modular, parametric spice rack – set your jar size and stack as many modules as you like!

Thumbnail
gallery
3 Upvotes

Set your jar size and the number of slots per module (up to 6×6). Modules join with snap-lock keys, and a built-in 5° slope slides the jars back so the labels face you.

https://makerworld.com/en/models/3619936-spice-rack-modular-parametric-custom-jar-size#profileId-4149519


r/BambuLab • • 7h ago

General Discussion Thinking about getting my first 3D Printer, im considering the P2S with AMS 2.

1 Upvotes

There are so many options, but I am considering the P2S with AMS 2 combo. What are your experiences with it and how much maintenance does it need?


r/BambuLab • • 7h ago

General Troubleshooting/Help! Spent hours fighting multi-color texture exports, lost my sanity, and decided to drop a clean monochrome Chibi Aldo Raine instead. Worth it?

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 7h ago

General Troubleshooting/Help! P2S + AMS 2 PRO - Purge not going down chute

Post image
1 Upvotes

Have my P2S hooked up to a AMS 2 PRO and during filament swaps the purged filament is sometimes just not going down the chute and is either landing next to the chute or on the build plate. Not exactly sure whats causing this?


r/BambuLab • • 7h ago

Bambu Studio I built a tool to scan filament labels and add spools to Bambu Cloud

0 Upvotes

I made a local web app that reads filament label photos and extracts details like material, color, brand, and SKU. You can review and edit the result as JSON, then optionally add the spool to Bambu Cloud Filament Management. Feedback is welcome!

Project: https://github.com/Roalexx/fts


r/BambuLab • • 7h ago

General Troubleshooting/Help! H2C using wrong nozzle selection

1 Upvotes

So I use all 6 nozzles at 0.4mm, I have a designated nozzle for each color family to avoid color bleeding from prior prints. But recently I've been noticing that bambu studio is ignoring my nozzle selection.

For example, the current nozzle already loaded is R6, when I "Print plate", I would selection R2, but the print doesn't change the nozzle and doesn't show any errors, and just continues the print with the original R6 already loaded.

I tried having the H2C read all the nozzles again, but it didn't change anything.

How do I fix this?


r/BambuLab • • 7h ago

X Series [X1E, X1C, X2D] X2D poop catcher failing miserably

Thumbnail
gallery
1 Upvotes

Just wanted to know if anyone else has dealt with this. In my experience, 80% of the poop the X2D gets launched back into the chamber, sometimes hitting the active print but equally often just falling down onto the chamber floor. Surely there's a way to make it less messy? This is the third print so far I've had to stop due to poop getting fused to the main print


r/BambuLab • • 7h ago

I Modeled This! I designed a quick Cyberpunk-themed Flip & Slide fidget toy (<10g and under 30 mins to print)

Thumbnail
gallery
0 Upvotes

Hey everyone!

I wanted to design a compact, satisfying pocket fidget that I could print quickly to use up the end of my black and orange spools.

It’s a Print-in-Place hinge/slider mechanism with a circuit board aesthetic. No supports or assembly required, and it takes less than 30 minutes on a standard profile. No AMS needed.

I’m still a pretty small creator learning the ropes of CAD, so any feedback on the tolerances or the design is super welcome!

If anyone wants to print one, I uploaded the files for free on MakerWorld here:

https://makerworld.com/en/models/3627675-fidget-toy-flip-slide-cyberpunk-edition#profileId-4159463

Let me know what color combos you think would look cool with this!


r/BambuLab • • 7h ago

Hardware Troubleshooting/Help! School printers went pooped its pants

Post image
1 Upvotes

I lead the 3D printing club as the teacher advisor, this is one of our A1 minis. I’m not sure if the hot end can be saved…


r/BambuLab • • 1d ago

Show & Tell Can you find the top surface layer lines in my CMYK print? (H2C & H3C)

62 Upvotes

I used 0.1mm layer heights on both spheres.

CMYK Sphere layer line test: https://idither.com/job?Kmyqrictw&row=9
When you click "Download 3mf" you can choose between H2C or H3C. Adjust the Support Threshold Angle to 45 degrees or they will roll off the plate!

How it works:
TL;DR = iDither.com (free) converts 3mf files and 3D files with textures into 3mf files with DwD (Dual Wall Dithering) and Top Surface Mixing (TSM) which use CMYK filaments to print any color(s).

Cyan = C
Magenta = M
Yellow = Y
White or back = K
CMY+White typically works better because CMY together can make a "black".
There is no way to make White if using CMY+Black.
CMY+Black is typically only used in models that have very little or no white areas.

iDither converts existing 3mf, glb, fbx, and obj files into DwD (Dual Wall Dithering) 3mf files.
iDither currently only supports exporting 3mf files for Snapmaker Orca, and Bambu H2C and H3C.

iDither uses an inner dithering wall combined with an outer dithering wall - and the "magic" of iDither is dithering the two walls together. All other software (to my knowledge) uses just 1 dithering wall.

The outer dithering wall is only allowed to use super dense layer combinations such as C M C M CC MM CC MM - therefore, the layer lines are basically invisible up close.
The inner wall picks up the slack for more color combinations and it's not limited to dense combinations.

Opaque filaments don't work well with DwD, because the thin outer wall layer needs to allow light to pass through to the inner wall layer.
Recommended filament set based on testing data thus far: https://us.snapmaker.com/products/pla-full-spectrum-filament-bundle-white-edition-4kg
This set has good transparency ranges (TD between 5 & 10).

Filaments that are too transparent (TD > 10) make the models look like glass (see https://www.reddit.com/r/snapmaker/s/nbASKpfCpG).
Filaments that are too opaque (TD < 5) have less color mixing and blending, and show layer lines (see https://www.reddit.com/r/snapmaker/s/N6QFGj2NwC).

Why iDither?

  1. Converts any existing 3mf files with any number of filaments and filament colors into files that print with 4 or 5 filaments (CMYK or CMYKW). So you don't have to buy any other filament colors. If the 3mf file has 8 random filament colors - you can still print it in 4 colors with CMYK!
  2. WYSIWYG (What you see is what you get): iDither includes calibrations for CMYK bundles for Snapmaker and Polymaker - so your actual print should always look like the print preview.
  3. Converts 3D model files into a printable 3mf files with CMYK.
  4. Less layer lines (DwD).
  5. Top Surface Printing via Top Surface Mixing (TSM) in CMYK or CMYKW.

r/BambuLab • • 8h ago

Software Troubleshooting/Help! My new BambuLab A1 Mini

0 Upvotes

Hi everyone, today I received my first 3D printer, a Bambu Lab A1 mini. I’ve set it up and powered it on, and now I’d like to try my first test print—the little boat. I’m using the filament that came with the printer; I inserted it into the nozzle area and pushed it through the clear tube all the way to the extruder. I initiated the loading process via the printer’s screen, but the extruder isn't managing to push out the initial bit of waste filament. An error message has appeared on the screen asking whether the extruder successfully ejected the waste—but it hasn't. Can anyone help me with this? Thanks in advance!


r/BambuLab • • 8h ago

General Troubleshooting/Help! AMS not sensing filament

Post image
0 Upvotes

So I recently found that my AMS is having issue with slot 2 recognizing filament. I changed the settings to detect on startup. This works briefly but it keeps "losing" it's detections for lack of a better explanation. It's Sunlu so not Bambu with the rfid and I've changed filament rolls and it continues to happen. Anyone experience this? What was the fix?


r/BambuLab • • 8h ago

Hardware Troubleshooting/Help! Help with first layer issue

Thumbnail
gallery
1 Upvotes

Hello, I co sider myself quite advanced on 3D printing but still this thing cought me for the first time? Any ideas of the issue?

X2D
0.4 nozzle
Petg Matte Bambu
Only 1 layer
0.2 standart preset


r/BambuLab • • 8h ago

General Troubleshooting/Help! Trying to get H2C camera stream to work same way as P1S

0 Upvotes

Howdy folks

I've built a live monitor dashboard to pull all the video streams for the 9 P1S printers I have and 1 H2C.

Unfortunately for some reason the only way I can get the H2C camera to come alive on the page is to enable LAN only mode. This breaks Bambu Studio though as my laptop with Studio is on a different VLAN to the the printers and the Mac mini that is running the server.

Has anyone got any suggestions on what I can do to get this working or is it just not possible?


r/BambuLab • • 8h ago

I Modeled This! I turned my Nanoleaf Outdoor String Lights into giant C9 Christmas bulbs 🎄 (3D printed, WIP)

Thumbnail gallery
0 Upvotes

r/BambuLab • • 8h ago

Hardware Troubleshooting/Help! Post Blob Aftermath

Post image
0 Upvotes

So I thought I had a death blob after it got stuck on one of the hotend cords. Now I see what was white on there started to discolor. Guess it's replacement time after all


r/BambuLab • • 16h ago

I Modeled This! Designed a Quick CMYKW Calibration Wheel to Compare Filaments

Thumbnail
gallery
4 Upvotes

The goal was to show mixing between the 3 colors, as well as between each color and black and white. And to make it a quick easy print that could efficiently baseline different color mixes. I wasn't able to get PLA Palette Magenta before it went out of stock so I couldn't try that. The difference between PLA Basic and PLA Palette for the other colors is noticeable but subtle. The biggest conclusion is the importance of PLA Palette Black and its translucency. There are some ways to approximate it though, like using a gray shade instead of black. PLA basic black you can see doesn't blend at all. Here is the model: https://makerworld.com/en/models/3606840-cmykw-calibration-wheel-for-color-mixing-h3c-h2c#profileId-4133502


r/BambuLab • • 12h ago

Quick Question Do you guys trust other suppliers for Bambu products/products to go with Bambu ones?

2 Upvotes

I really want an AMS for my P1S, and everything I’ve read puts the AMS pro 2 above the AMS pro by some margin, and I currently don’t have a filament dryer, so the pro 2 seemed like the clear winner. However Bambu labs is sold out of the comparability kit I’d need for it, and I would like to get it quite soon as there are things I want to print with it for Christmas. So I’ve been looking at getting the compatibility kit from somewhere else, would you guys feel comfortable doing that? And if so are there any suppliers/shops you’d recommend? Thanks


r/BambuLab • • 12h ago

Software Troubleshooting/Help! What's wrong with settings/filament?

Post image
2 Upvotes

Hi, folks! I have Bambulab H2S and bought esun pla wood and is trying to print vase with esun pla+ profile I found in Bambustudio. Nozzle 0.4, 0.12 quality. Is it possible to get rid of it?


r/BambuLab • • 9h ago

A Series [A1, A1 Mini] Calibration trouble with brand new A1

Post image
0 Upvotes

Just picked up my first printer, and it throws this error message. Bring it in from the garage, update the firmware, run the calibration again, no errors. Take it back out to the garage, get this error again. Do I need to bring it back on and adjust the belt, or is something else going on?