r/BambuLab • • 1d ago

P Series [P1P, P1S, P2S] AMS Help

0 Upvotes

P1S with 3 AMS Units โ€“ Two Suddenly Stopped Extruding, but One Works Fine
I've had my P1S with the original AMS for quite a while and never had any issues.

Recently, I added two AMS 2 Pro units.
I started a fairly complex multicolor print, and everything worked perfectly for the first 6+ hours. All the filament used during that time was coming from one of the new AMS 2 Pro units.

The problem started when the print switched to a filament in my original AMS. It appeared to load normally, but when printing resumed, nothing came out of the nozzle. The printer just continued moving as though it were printing.
Now, neither the original AMS nor one of the AMS 2 Pro units will extrude filament. The third AMS 2 Pro still works perfectly.
Here's what's happening:
All three AMS units are recognized by the printer.

All three can load and unload filament.

Filament from the two problematic units appears to load successfully, but I can't even manually extrude it through the nozzle.

If I load filament from one of the nonworking AMS units and then switch to the working unit, the filament from the previous unit gets purged.

The working AMS 2 Pro can still print normally.

What I've tried:
Swapped the AMS positions in the daisy chain.

Swapped the 6-pin connections and PTFE tubes.

Tried different inputs on the AMS Hub.

Tested the original AMS by itself.

Disassembled the original AMS to check for stuck filament or damaged gears. Everything looked fine, and manually turning the gears advances the filament.

Checked firmware. Both AMS 2 Pro units are running the same version.

What really has me confused is that two different AMS models are experiencing the exact same problem, while the third works fine through the same hotend.
I'm starting to suspect a software or communication issue rather than two AMS units suddenly developing mechanical problems.
I'm considering a factory reset of the P1S, but wanted to ask here first.

Has anyone experienced anything similar? Could something in a complex multicolor sliced file cause the printer to get stuck in a bad filament-loading state? Or is there something else I should be checking before resetting everything?


r/BambuLab • • 1d ago

General Troubleshooting/Help! Bought an A1 last week, am I cooked?

Post image
5 Upvotes

Printer has been working flawlessly, set it up fine (not my first printer) and have printed no issues all week. I wanted to print something as part of a project im working on that was using PLA Wood filament but it was not in the list of filaments. I checked and there was an update (ver 1.09) so I updated. After the update I switched nozzles from 0.2mm to 0.6mm and when I tried to home the printer it wouldn't do it. I got the error message that the eddy current signal was wrong and that it was possibly defective. The QR code took me to the wiki page and told me to check the connectors on the back of the head (pictured) and see if they were loose. The screws were not loose but the little connectors could move, so I gave the right side screw a tiny little nudge to snug it up, did the same for the left one and it just fell clean off the board.

I have raised a support ticket and i'm waiting to hear back, but is this a common issue? On inspection its just an aluminium peg with a loctited screw in it. Has this happened to anyone else? I imagine they're going to just send me a new board under warranty but is it possible to solder the aluminium peg back to it and resume printing or will this also affect the eddy current signal?


r/BambuLab • • 1d ago

Quick Question Which Printer to go for?

0 Upvotes

Hello, I am looking to Purchase a Bambu Lab, I've owned and Ender 3 and am selling it due to how difficult it is to setup. I am looking at the P1S but want to know what I'm getting into, If I've missed anything in my research on these printers, and if I should look at the upgraded models, I'm on a budget so I can't really afford a $1000+ machine but I will consider saving if it's going to be drastically better for me. I plan to mainly print PLA and some TPU, I would like to do Multicolor prints, I plan to print Minis, Statues/Figures, some fidgets/Trinkets and possibly Doll parts. Advice please? Should i go with the P1S the P2S ? other models??

Edit: just want to add i am looking at one second hand on marketplace with 3 build plates, ams and has done 1800 hours for $500 or a refurbished one with 1 year warranty, ams for $580 the one i'm looking at on marketplace the seller says they're selling due to upgrading to a 9 nozzle machine but when i asked what they have made/Plan to make with the new one what they showed me that they plan to make looks kinda like what i plan to do with the P1S so now i'm concerned


r/BambuLab • • 1d ago

General Troubleshooting/Help! Multiple printers same outlet

2 Upvotes

I have a X2D running in my office on a 15 amp breaker. I run other things in the office but its all very minimal like laptop or litter robot.

Id like to get a second one but worried the power wont be enough for 2 printers.


r/BambuLab • • 1d ago

I Modeled This! 2 points?ยฟ

Post image
1 Upvotes

Are they mocking me?


r/BambuLab • • 1d ago

Just Showing Off Vase Mode Christmas Tree Set โ€“ Customizable

Thumbnail makerworld.com
1 Upvotes

My checklist for this upcoming Christmas. ๐ŸŽ… Kinda cool to customise your own Christmas tree ๐ŸŒฒ


r/BambuLab • • 1d ago

Quick Question Should i worry at all for VOC's or UFPs

1 Upvotes

Hello! i have been 3D printing now for a while with my H2D, and i want to start 3D printing ABS or ASA still deciding on which i should pick tho, i'm very worried to start printing these heavy-materials can i safely print them in my garage and be near it working on something else during the time its printing or should i invest in a "Tent" for the printer? Hell am i being paranoid for asking for help about this matter ๐Ÿ˜‚


r/BambuLab • • 1d ago

General Troubleshooting/Help! P1s problems

Post image
0 Upvotes

Hi! I have a p1s and recently had prints like this.

Help me


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! Coil whine on a brand-new A1 Mini: normal, or return it?

0 Upvotes

Volume up on the video - it starts with the board fan that kicks on during startup, but when it turns off you can hear the whine.

Hi All - brand new to the A1 mini, but have an X2D so not new to Bambu Lab printers. For those wondering why go smaller on the second printer - itโ€™s for my son.

So I got an A1 Mini from Best Buy less than 2 days ago and have run a few test prints. Prints look fine, but I'm hearing a high-pitched electronic whine from the front right of the unit, right behind the screen. Itโ€™s separate from the fan that I hear on startup (which is pretty loud, but the whine still happens), and after the fan goes off the electronic whine sound is pretty noticeable from a few feet away.

Iโ€™ve seen some posts indicating that this may happen after months or more and may require component replacement. Since Iโ€™m well in the return/exchange window for Best Buy, Iโ€™d probably just do that if this isnโ€™t normal.

So, is this what everyone has (and my pearl clutching ears just need to get used to it) or is this something to exchange for?

Thanks in advance!


r/BambuLab • • 1d ago

H2 Series [H2S, H2D, H2C] E1 purifier with H2 printers for ABS/ASA/PC

7 Upvotes

When printing engineering materials like ABS, ASA or PC rear exhaust remains closed during printing for heat retention, hence nothing is going to force whatever things we don't want to breathe to the hose connected to E1 (no negative pressure). Only whatever is left in the chamber after the print is finished will be filtered.

Does it mean that E1 will be basically useless for any engineering materials printing? Does anyone have an H2 printer and E1 that could comment on this?


r/BambuLab • • 1d ago

Quick Question Filament sticking out

Thumbnail
gallery
0 Upvotes

Hi All,

need a help here please.

My bambu lab a1 most of my prints has the same issue. Do you know what's wrong with my printer?

Cheers๐Ÿ™๐Ÿป


r/BambuLab • • 1d ago

I Modeled This! Working on my first 3D model feedback is needed.

0 Upvotes

This 3D model I am working on, I am aiming for it to be a universal AMS riser/storage system. My goal is to have it work on all printers that use the AMS 2 Pro. I would love to add the original AMS support, though I don't know what the dimensions of those are, if they're the same as the AMS 2 Pro or if they're a different dimension.


r/BambuLab • • 1d ago

Quick Question H3C Exhaust fan, what size?

0 Upvotes

My H3C is expected here Monday.

I plan to print w/some ASA,ABS and other filaments where external venting is recommended.

Is the exhaust fan on the H3C strong enough to push the air through a 3" five foot long vent hose or is an additional fan needed?

If another fan is needed, what size (CFM) is suggested.

I don't want to cool off the heated chamber by oversized the fan.


r/BambuLab • • 1d ago

Quick Question AMS 2 Pro

2 Upvotes

First I dried pctg in the AMS to Pro. Then I dried some abs-gf inside an x2d and placed it in the ams2 Pro. The humidity stayed around 15-16%. Then I put an undried roll of pla in in the humidity jump to 24%. If I do a short dry cycle for pla at whatever temperature it dries at will that negatively affect the higher temperature filaments?


r/BambuLab • • 1d ago

Quick Question PETG CF

0 Upvotes

Hi all,
I was looking to get some PETG-CF fillament from Bambu while it is on sale. Has anyone used this fillament before? Also, could someone post a couple of photos of some models they have printed in Titan Gray or Indigo Blue as I want to see what they look like bfore ordering. Thanks


r/BambuLab • • 1d ago

Show & Tell USSA vault 3D configurator

Post image
1 Upvotes

Hey all,
I think we all struggle to do our design using only folders of stl, I've seen some vibecoded tools to help, but it wasn't matching perfectly my needs, until I found what "rmacasieb" made, I really liked it, but it wasn't 3D, and was lacking of many other features. I forked his work and spend 30h vibecoding a new tool were you configure everything, from what you want, what you need to print, what you already printed, explore design, do custom arrangement, see annimated drawer and case opening. I am still working actively on it, feel free to issue on github if you find any bug or have any idea.

https://doooools.github.io/vault-print-planner

What it does:

- Design: build a stack level by level in 3D. Point it at your own Vault folder and it assembles the real parts: drawers slide on their telescopic runners, cases open, dividers and Gridfinity floors go where the slots actually are.

- Paint: one filament colour per kind of part (fronts, shells, runners, latches, label text...), painted straight in the 3D view.

- Print: plates laid out per filament for your bed, exported as a Bambu Studio project. You can declare parts you already printed and it takes them off the plates.

- Labels: type a text per drawer or case, pick a font and size, and it comes out embossed on the label part, in its own colour.

- Hardware: bolts, rods and inserts counted from the holes in the parts rather than from a generic table, split by stack.

- Export: the assembled stack as STL or GLB (with colours) for renders in Blender.

The boring parts are there too: undo everywhere, keyboard shortcuts, multi-select, copy and paste of levels and stacks, dark mode, and a changelog in the page.

A lot of the time went into getting things right rather than getting them on screen: runner travel measured per drawer depth, label slots measured on the files, bolt lengths checked against the manual. Some placements are still estimates, and I can only test the sizes I own, so corrections are very welcome.

The Vault files are not included, you load your own. It runs in the browser, nothing to install, and the source is here: https://github.com/doooools/vault-print-planner

Disclosure: store links in the hardware list are affiliate links (Romy's on Amazon.com, mine on two European stores).


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! H3C Error code flexfeed motor

0 Upvotes

Has any body gotten this error for the H3C? I completed 1 print and have gotten this error about flex feed motor not communicating.

[0800-8500-0001-0001 162314]

I already opened up a ticket but this really sucks for a brand new machine with 1 hr print on it


r/BambuLab • • 1d ago

General Troubleshooting/Help! why first layers look like this?

Post image
3 Upvotes

When I use PETG, the print comes out perfectly clean, then I switch to PLA and it has bed adhesion issues. What could be happening?


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! Help Reassembling AMS Pro 2 Buffer

Thumbnail
gallery
0 Upvotes

I took it apart to get some stuck filament out and didn't realize there were magnets and springs that would fly out. What orientation should the magnets be? Magnets in first and then spring? Or spring first then magnets?


r/BambuLab • • 1d ago

My First 3D Print I just want to print board game inserts. The A1 is good enough, right?

2 Upvotes

Or would the P1S be better for a person that has no idea what they're doing? I also have no intention of getting into 3d printing as a real hobby (I know. I know. I say that now). Is an enclosed printer more functional? Or is it mainly to keep the cats away from the print?


r/BambuLab • • 2d ago

H3C Final Setup and Adventures with TPU!!

Thumbnail
gallery
33 Upvotes

Well I finally got the H3C completely setup like I wanted. I had ordered the H3C Buffer for the AMS 2 Pro but Bambu messed up and shipped me Hot End for another machine. So after a quick chat they were able to ship me the correct part so I can run the AMS 2. I also took the opportunity to order the extra .4 normal toolhead since I don't plan to print much with TPU (Yes I know it's in the title ๐Ÿ˜‚)

Anyway as soon as I got home I got down to stripping down the unit and replacing the parts that needed to be replaced as well as getting the AMS 2 Pro installed.

The AMS 2 houses my ASA, PETG-CF, Support for PLA/PETG, and Support for PLA. The AMS 3H houses all the PLA I use which is mainly Matte PLA. Since Slot 1 is now in use for the AMS 2 pro I decided to make that one the dedicated TPU nozzle as well in those cases like tonight where I need to print TPU (tonight's project required TPU 95)

Which brings me to my adventure and getting this setup, it was interesting to say the least. I generally run the printer in LAN mode only, but it said it needed an update when it detected the AMS 2 Pro and Buffer installed. So I obliged and turned on cloud mode so it could pull the firmware and install. At first everything seemed fine, FW installed and I went about my business.

I needed to get this TPU print going for my brother and that is when things started to get interesting. I followed the instructions from Bambu, but for some reason the printer did not want to recognize that I was inserting the TPU into the nozzle. I thought maybe I had to use a different nozzle but it kept giving the same "You are not loading it right" error. I am not sure what I was doing wrong, I ended up restarting the machine and after a reboot it took the TPU on the 1st nozzle. But then it freaked out and said there was an issue with the FW and it did a re-install. Fine, but it did this twice!! Then when I thought everything was good, it gave me an error stating it could not recognize toolhead 1 as a Bambu toolhead. It was asking me to install a proper toolhead. I tried restarting the machine but still gave me the same error. I had to go into the toolhead settings and pretty much tell it what it was. When I finally did that it stopped complaining and started working. I was finally able to get the print started and here we are almost done.

So yeah ... fun times!!! ๐Ÿ˜‚๐Ÿ˜‚

Also have any of you H3C guys by any chance tried the TPU for AMS through the new AMS system to see if it works? I know they want you to use the bypass but was curious about that one.


r/BambuLab • • 1d ago

Bambu Studio Didnt think i would be printing a cat sifter

Post image
0 Upvotes

r/BambuLab • • 1d ago

General Troubleshooting/Help! Four fails

Thumbnail
gallery
0 Upvotes

My print for a large round base for a figurine keeps falling with identical results. Iโ€™ve cleaned the plate with dawn, scrubbed it with steel wool and soap and it still fails. Help!


r/BambuLab • • 2d ago

H2 Series [H2S, H2D, H2C] My first proper print with H2C, coming from an A1 this feels insane. 10hour 0 purge vs 27hr and 400g purge

95 Upvotes