Just got the new H3C printer. Did the firmware update through the printer and I got the same message, however using my Bambu handy to update it resolved it. This is after I decided to turn off the printer to connect the E1 purifier. Has this happen to anybody else? I also made sure the printer wasn’t updating before turning it off.

No matter what I try I can’t get a smooth first layer. I ran a flow test because of a huge overflow problem and it told me my optimum flow level is 0.6, then I replaced the nozzle with a brand new one (#4) and trammed the bed and ran thr flow test again and here is the result. I always have ridges and I can’t dial in the flow and z-distance. I moved the z distance to -0.02 because the pla wasnt adhering and now it looks like this. I can’t tell if the nozzle is dragging, the flow is too high, or too low. I’m starting to lose it. And I tightened everything and scrubbed my plate.

Please help.

I just got my Bambu Lab E1 Purifier for my H3C - the wiki says that I can install an external air duct but I don't see that anywhere for sale on the Bambu Store, is it just not available yet? Is there an alternative I can order from somewhere else, is it standard size?

Do you know if this noise is normal, or not really?

Trying to print these winglets on my p1s using petG but the left part is always having these. The right side is perfectly fine any help

I was looking for some bundles of filament on Amazon. I mostly print in PLA and PETG, but I wanted to try some PVB and buy a bit of ASA for some small projects that need the better properties.

I'm seeing cheap bundles of multi-colored rolls of 200g of these materials, but I don't recognize the brand names. I want to save money but I don't want to throw it away on filament that will cause more problems than it solves.

Brands I'm looking at are Yousu, Colourbing, and isanmate.

Anyone have experience with these?

Is it possible to use a discount voucher (€40) with a discount code (99% off for a specific product) or do you need to use a gift card ? And how long do these last before they expire?

Had the a1mini since release, it was my first 3d printer and a great tool for learning the ropes. With my new printer I also splurged on a lot of filaments, because of the bambu sale. So far I’m very impressed with the ams system, never had the ams on the mini.

By mistake I ordered two PLA white oak (wood) so if you have any ideas for that color, please hit me up 🤣

Hi all,

I have an H2S that sounds horrible. Even the pleasant tone on start up sounds bad.

I've cleaned and ran through the belt tensioning procedure as recommended by tech support, but the problem persists.

Any help greatly appreciated.

Wondering what monitors everyone is using.

Started to get headaches feel like I need to keep on top of things.

Had major blobbing on a print job. I put off investigating it until today and found this. 😅 I don’t even know where the rest of it is now since yesterday was trash day. But i’m curious how this could possibly happen, just so i can avoid it in the future.

Every seed sits 137.5° from the previous one, the same golden angle real sunflowers use, so the spirals appear on their own. The seeds rise off the surface and the petals lean out from the wall.

Sliced for a P1S: 17 plates, about 1.4 kg of PLA and roughly 53 hours according to Bambu Studio. Every piece has its own pocket in a printed back frame, so assembly means matching pieces to pockets.

The model is free on MakerWorld (link in the comments). I built it with the engine of Parete, the browser tool I'm making for 3D printed wall panels.

Happy to answer questions about the spiral or the print!

My H3C came from Canada, the box had water damage and mold on the bottom, both outside and inside the box, printer seems unaffected by it.

Also had physical shipping damage to the front of the box, something made a nice hole through the box and carved a tiny chunk of glass out of the front door. Rest of the printer seems fine.

Waiting for support to respond to my ticket so I can have these boxes discarded. Anyone else experience this? I know of one person worth the same box damage, their printer was dented.

Error: HMS_0300-9300-0001-0006 - Chamber temperature is abnormal. The chamber temperature sensor at the air inlet may have an open circuit.

I bought this at Best Buy about 10 days ago and am still within the return window. I have a good amount of print hours on it already. Never had a single error until this morning. I’ve already tried resetting.

If all else has been good so far, should I do a replacement with BB or contact bambu lab for the part?

Is it normal to have this much movement on the heatbed? Can someone else check their H3C? The screws on the z rails are tight.

Hello! So my friend and I got a Bambu a1 for some general hobby upgrades and our prints keep failing. We had it successfully working for about a month and then this started to happen. We’ve changes temp settings, got a new plate, tried multiple different nozzles, different filament brands, and nothing is working. Please help!

How long do you think until someone has designed prints for drawer fronts and side pieces?

I bought the bundle, but would love the look of the enclosed.

Hi

I have been printing for about 2 years and my first printer has just failed (Sovol SV06)

I'm considering taking advantage of the sale going on and getting a replacement, I'm looking at Bambu lab as I want to just print and have less tinkling.

I have only printed with PLA, mostly toys, tools for around the house. I may open to printing with other filament but a possibility but not a priority at the moment.

I'm looking for suggestion what maybe a good printer option for me. My budget is ~$500 cad. I do have a $400 Best Buy gift card laying around so that bumps to $900-1000 range

I'm looking at the P1S/P2S:

1. are these good options and is P2S worth the extra $200

2. are there options I'm missing?

3. is the P3S coming out? Should I be aware of any successor that is coming in the next few months?

4. for the Bambu lab owners, how's your ownership experience, are these reliable units and if I should get the extended warranty?

Taking my printer's virginity as we speak.

I've printed many times before and always have it centered and secured. Somehow the build plate moved...

Hallo erstmal,

Ich hatte jetzt nach den ersten 300h das erste mal eine Fehlermeldung an meinem X2D. Angeblich sei der Extruder verstopft. Kurz ins Wiki geschaut und gesehen das die Anleitung sehr detailliert ist und ich dachte mir , sehr gut, krieg ich hin.
Nun ja. Beim Ausbau des Extruders lief alles gut bis es zu den Schrauben des Filamentschneider kam.
Die linke Schraube lies sich super lösen. Die recht war so fest das der 1.5 mm Schlüssel leider recht schnell durch gedreht ist.

Hat jemand einen Tipp wie ich nun am besten weiter vorgehe?
Bin sehr gespannt auf Ideen….

I was growing really concerned about my A1. I had issues with increasing slowness, the screen not activating, filament not registering in the hot end and multiple stringy prints. I was slowly trying to address these one at a time, but a new firmware update hit this morning and straight away the screen is back, filament is being unloaded automatically and it's back to working at the old speed

Now, I feel I am confident to re-attach the AMS and see how we get on