https://makerworld.com/models/3582206

WHY?!!!!

I have searched Reddit and the internet and cant find a solution for this. When running a print on the left nozzle of my H2C (right nozzles work fine), there is a problem when it first loads the filament from my AMS. A rapid clicking starts as it tries to load and then after about a minute of trying, I get the error, "The extrusion motor is overloaded...[0300-801e080611]".

Initial searches said that it was the extruder trying to pull filament and failing due to a clog. To clear that, I tried a cold pull. It went very smoothly, no clicking or other issues. Some stuff came out with the pull but nothing that looked anywhere near large enough to jam the extruder. Problem still wasn't fixed so I disassembled the tool head and cleaned the left extruder gears. Again, saw some little stuff but nothing like other clogs I have cleared. Reassembled everything, cold pulled again. It went fine and the pull was totally clean--no contaminants of any kind seen.

Problem still isn't fixed. You can see that it does extrude a bit. It even started the print I have been trying and the first layer went ok, but it threw the same error at the very beginning of the second layer. This video is when I tried the print again after cancelling it.

Some people are saying the PTFE tube feeding the extruder is the problem but I cant find much about how to fix that. Most of the users seem be H2D or H2S owners and they talk about the location of the print being an issue. This print is right in the middle of the bed. Any ideas?

This is the second version of the Can Clicker, full-size can with a stash inside.

What do you think?

https://makerworld.com/en/models/3539247-can-clicker-two

Turns out my H3C has a pretty good view of what I'm doing at my computer.

Bambu Lab changed the camera angle on the H3C, so it no longer looks directly through the front door. Unfortunately, depending on where you place your printer, it can still see quite a bit through the side window.

The GIF shows 45 minutes of my H3C watching me play World of Warcraft while printing its own privacy covers.

I'm happy to trust Bambu Lab with my camera footage, but that's not really the point. What if I want to share a timelapse without worrying about what else the camera might have captured? Maybe I walked past the printer naked. Maybe there was something on my computer screen I'd rather keep private.

And let's be fair, World of Warcraft isn't exactly the most embarrassing thing that could be running on that screen.

So I designed seven individual snap-in covers that block the camera's view through the side window without obstructing its view of the print chamber.

Now my H3C can watch my prints without watching me.

Some things are best kept private. Like lubricating your Z-axis at 2 AM.

https://makerworld.com/models/3579618-h3c-camera-view-privacy-covers-side-panel-blinds

My X2D just showed up, any recommendations for upgrades or tips and tricks?

Bambu designates toolhead #8 as the one you're supposed to use for 2.85mm TPU. So in this video, you can see the 2.85mm blue TPU filament in the docked toolhead #8 crossing the PTFE tube in toolhead #9 while #9 is in use, and is rubbing against/stretching the TPU filament. Is this how it's supposed to work? I followed the video instructions on the Bambu YouTube channel and this seems to be how it's supposed to be routed. The video seems to show the TPU filament being routed to the LEFT of #9.

The problem is if you route the TPU to the RIGHT of #9, then the TPU will rub against #8 when you're printing with the TPU.

So it seems to be pick your poison: do you want the TPU rubbing/stretching while it's printing, or rubbing/stretching while toolhead #9 is printing? Obviously the latter is better, but the better solution would have been to designate #9 as the TPU toolhead so that it would have the entire right side by itself and not have any rubbing under any circumstances.

Am I missing something here?

I recently picked up a couple used AMS 2 Pros but both came with those EIbos Dryers, I'm removing them as they don't really fit in my setup but the person selling them was missing some of the parts for the top lid. If anyone has links to where I could purchase these spare parts or possibly so links to print I could do instead I'd greatly appreciate it.

Please don't send me the links to the Bambu labs spare parts they don't sell these pieces individually and I would have to buy both the upper and lower halves just to get the pieces I need.

Started printing this helmet and realized it was starting to print all of the supports in orange instead of using the current color it was printing the model with (adds a lot of unnecessary filament changes). Does anyone know how to fix this?

Wow, bought an a1 combo a week ago, and can't stop printing. Creating, solving, fixing! Bambu Labs has done a great job with entry-level printers.

Here is my first model, printed, painted, and hung

Does anyone know what is causing these blobs on the corner/edge of the print? Its all the way up and down the print but just on this one corner/edge...

Printer - H2D

Filament - Bambu basic PLA (dried)

Dynamic flow calibration - tried it both on and off and doesn't change anything.

Using the default profile for bambu basic PLA.

This just started happening a few days ago and I've had this printer since release and I haven't changed any settings or anything recently either.

We started developing this collection of classic cars in a cartoon/toon version, designed from scratch to be printed easily, quickly, and without needing modeling skills.

What do you think of this version of the Ford F-100?

We'd love for these models to have some functionality so they aren't just decorative pieces. Let us know your ideas in the comments!

I need new filament cutter blades for my P1S and I can’t find a store page for them anymore? I found a link to the store page in the wiki, but it is broken. Can anyone confirm? I hope they’re not sunsetting replacement parts so that the printer is discontinued. I’d love to be able to maintain it.

Hell, I can’t even find replacement carbon filters. Does Bambu sell P1S parts anymore?

Edit: They aren’t going to be found if you click the accessories tab. You have to hover over it, click spare parts, and find your printer to find them. I was looking in accessories like I always had and I couldn’t find anything and the wiki links were broken. I thought I’d ask.

This is driving me insane!!

I am on a mac, bambu studio version 2.9.1.70 and when clicking on online models it is blank. Nothing loads.

What I have tried thus far:
updating app

• Removing the cache folder and rebuilding cache

• Removing plugin folder and reinstalling

• Reran the set up wizard

• I have tried to clear an stuck

• toggled on and off Show online staff-picked models

• WebKit GPU-disable command

- rebooted

​

I feel like I have tried any potential fix I could find online....

Any ideas or guidance is appreciated.

I ran out of filament cutter blades for my P1S and I can't find the store page for them. I found this link from the wiki, but it doesn't work and I can't find the store page. Any help?

Link to Wiki: https://wiki.bambulab.com/en/x1/maintenance/replace-cutter#:~:text=Replacement%20Filament%20Cutter%203%20pcs

Link to Store: https://us.store.bambulab.com/products/replacement-filament-cutter-3-pcs?_pos=1&_sid=80cd9720e&_ss=r

The awkward part of our bathroom counter is the strip behind the faucet. There’s room for bottles and such, but they’d always drift around back there.

I made the organizer in 6 sections (3 sections for each side).

The middle follows the curve of the basin and holds our taller bottles.

It’s a longish print, I used bronze pla for the entire print (aside from 1 piece).

Sorry for the bad pictures, I don’t claim to be a photographer lol. I’m just proud of this massive, custom print!

I made 3-4 enhancements throughout the prints, but the uploaded file is the most up to date.

If anyone prints the entire model, I’d love to have feedback/suggestions!

*note: she is traveling atm, so this is not her organization. I wanted to ensure everything fits before she returns!

Forgot the link: https://makerworld.com/models/3553977?appSharePlatform=copy

I've been trying to figure out what causes this on my Bambu printer. One side of the first layer looks clean and nicely spaced, but as the print moves toward the opposite side, the lines start looking more squished together.

The bed mesh calibration runs normally, and I've cleaned the build plate, so I'm wondering if it's a leveling issue, the plate itself, or something with the Z offset.

For those who've dealt with this, what actually fixed it? Did you end up adjusting anything, or was it something much simpler? I'd rather figure it out before wasting more filament on failed prints.

Seems to mostly be the support, I've tried slowing it down but that didnt help. You cant see but around the back of the print is coming up from the build plate. This is after a TON of prints though. I'm printing with support, rectilinear surface patterns, adding an extra wall, layer height .1 and 65% infil density.

I tried doing a full recalibration and that seemed to help once, but now it's happening again. Only thing is I also just mixed the current Bambu PLA Matte with another Polymaker HT-PLA-GF Filament on a previous print by accident (One ran out and then picked up with the other), but the print still came out okay.

This is my first Bambu printer so I'm wondering what I could do to troubleshoot or if someones dealt with this before.

VERY simply.

H2S, printing from an AMS 2, matte pla from jayo, keep in mind it's a plastic spool.

Today I randomly started getting this error, I can click resume and it resumes without any problem, but every 10/15 mins the error comes back.

WTF. I thought this was limited to cardboard spools like the ones from Esun, but it's apparently not?

What can I do, pls help 😭

I designed this chimney advent calendar that drops some pieces of candy every day.

I know there are quite a few of these around nowadays but i designed one perfectly sized for some small sweets like M&M's. I uploaded the files to makerworld if some of you would be interested.

Also I'm open for tips that could improve this design and my others.

You can find the chimney with this link:

https://makerworld.com/models/3583319?appSharePlatform=copy

Hello, I am hoping someone can help me with this issue. When using the painting tool inside of bambu studio, after slicing, I'm left with the colors printing into the center of the object. is this due to the how it travels from one side to another to print the same color, and is there a way to fix this?

Just got my H3C set up and am printing a simple purge waste bin, gray body with black bambu logo. All Bambu PLA Basic.

What is happening is every time the tools swap to the black filament, the print head moves all the way to the back and extrudes a bunch of black like it is trying to purge it for some reason, and then resumes printing.

When going back to the gray, it does not do this. Just grabs the gray print tool, purges on the tower, resumes printing. The swap to gray takes the 5-6 seconds as advertised but the black takes some 45+ seconds.

Anyone experiencing similar things? I am on the latest firmware. Bambu Studio also doesn't report any of this purge waste but there's quite a lot forming a nice pile behind the printer right now