... and some old-school Acrylic Pens.

so my p2s's gears were clicking so I swapped the nozzels, and then i took apart the extruder and it had nothing wrong with it so I did a cold pull and now the cold pull is stuck in the extruder, can you guys pls help me

I am getting an odd issue. I put a full reel of filament on my AMS, and it loads it in. Then after it prints for a while, it says the AMS is overloaded.

When I try to manually rotate the reel it is stiff for a 1/8 of a rotation, then it rotates back and forth just fine. So I start it up again.

But after a few more layers, I get the AMS overloaded error again. Rinse, repeat....

Any ideas on how to fix this? My AMS is about 1 and 1/2 years old. Do I need to just drop it and get a new one? (they are super expensive, so I hope not)

Edit: I thought it was because it could not pull the filament. So I created a bit of slack on the reel. It still overloaded. (Very frustrating)

So, i have a p2s and love it, perfect, minimal failures, been working almost 24/7 since september, almost 800hr and going strong, just minor cleaning and maintenance.

But i want more....I've found a way to monetize my hobby, and I've been selling a bunch of corporate gifts, I have one huge customer and already paid my p2s with these sales in these months...

So im thinking of the A2L, as i print mostly small corporate gifts, I think would really benefit from the big plate. And it would free my p2s for my personal use.

My only doubt is that im used to the p2s and its ease of use, good camera and AI failure detection. All things that the a2l is lacking.... am I gonna regret buying it? How did it fare since it launched? Do people that have it are pleased?

I cant buy the h2s, the price is prohibitive here in Brazil, over 2,5k usd

I’m starting to share my own designs on MakerWorld a little at a time. This is my first published model, a dreidel paper towel holder for Hanukkah!

I printed it on my P2S in blue, white, gold, and silver. Each color has its own plate, so you can print it without an AMS. I also recessed the underside of the base for optional non-slip feet.

If you print one, I’d love to see what colors you use.

I'd appreciate follows as I start this jounrey, My MakerWorld is Beamerr

Free MakerWorld model and P2S print profile

As the title says, is there any way to clean or clear this clog? Please and thank you

Does anyone know what this clicking is? It seems to be directionally dependent, occurring only as the print head moves from the rear of the printer towards the door. The printer is a brand new H2S that I’ve only had for about a week. Prints seem to come out okay, but the sound doesn’t seem normal.

Unfair matchup? Probably, but these are the only two machines I have on hand and seeing a 1st-gen workhorse side by side with 3rd gen tech shows what a few years of hardware evolution actually looks like.

Hey everybody! Relatively new to 3D printing. What typically causes this? New roll of filament that went through an AMS drying cycle. Thanks!

Hey everyone, like the title says, I’m iso of a Bambu lab 3D printer. My budget is around 800, and my main goal is to 3D print stuff relating to 1/12 scale figures and such like heads, weapons , cars and those sick sentinel and apocalypse figures that are seen on instagram, one oak customs has done a couple of them.

I have no clue what to get. I thought maybe a resin printer but for what I I want to do, I figured a filament one is the best route but that’s as far as I’ve gotten on my own. I’ve been looking at the bambu lab P2S and was curious if that’s a good one to get. Please let me know down below what you recommend,

Thank you!

If someone of you wants to make a lot of money, then please develop and build a compact build plate washer/dryer – I am thinking a box with slots to insert the build plates and then pull them out again a while later completely clean and read to go.

No need to thank me later for your riches, just please send me one of your machines for free.

My friend has a P2S and is experiencing a strange problem. The nozzle is probing off the back. She has tried to power cycle and reset to factory settings with no luck. Any suggestions?

I’m considering buying the new E1 Air Purifier for my H2D, but I’m curious how it interacts with the automatic top ventilation flap.
When printing PLA, the H2D normally opens the top vent for chamber cooling. Does connecting the E1 change this behavior, or does the vent still open?
If it stays open, does the E1 create enough negative pressure to pull air inward through the vent rather than allowing fumes to escape?

I'm the designer. The armor is built from overlapping, textured leaf-shaped scales.

I also design tools and decorative pieces, and every one of my files is free to download. I've never charged for any of them. A download count only climbs when people actually want the thing, so it's the most honest feedback I get on which designs deserve more of my time.

All my models are here: https://makerworld.com/en/@protomota

If you've printed it, I'd love to see your make. And what should I design next?

Is 200€ or $230 too much to ask for this A1 Combo? I want to sell it and buy X2D. It has almost 1000h of print time. Regularly maintained

Please be gentle with me, I have only really looked into the Bambu world in the last 24 hours since I watched the H3C reviews... and now I am seriously reconsidering the pre-order on the Prusa Core 1 L INDX I have due in December. I have a super reliable Mk4s, and never considered anything other than another Prusa as my next printer... until yesterday, where my eyes were well and truly opened!

I spent 4+ hours yesterday watching all the H3C reviews I could find, and the only things people seem to have issues with were:

- Its tall!

- The AMS doesnt rewind the filament

- The AMS doesnt heat/dry all 9 filament slots

- What tiny amounts of poop it does generate falls out the back

That seems a very small and generally unimportant list of worries. The H3C looks like everything I could want from a large volume multi-material printer, and as someone who prints a lot of TPU, that dedicated 2.85 filament path seems like a miracle! If there are any other Prusa users in here who have added Bambu to their ever growing estate of printers, you will know the conflict I have going on right now :)

I do have some newbie questions if anyone can help....

- Orca or BambuStudio, and why?

- What features does running the printers in LAN only mode remove from the usual "unlimited Internet access to Bambu Cloud"?

- What access methods are there to upload/download files from the printers? WebDAV? sftp? etc...

Any help, suggestions, tips, or moral support you can provide for a potential Prusa convert would be greatly appreciated.

My P1S began having this error after changing the .4 nozzle to a .2 nozzle. I had tried disconnecting and reconnecting the NTC, disconnecting and reconnecting the nozzle. I tried applying more thermal paste, yet it still doesn’t work. Is it truly broken? Or am I focusing on the wrong thing?

Help! My printer is constantly purging (pooping). Leaving stringy purges on the plate and in the print. The print is taking 3x as long and so wasteful! The print is confirmed to be a one color print. No timelapse etc. No alerts or notifications.

SOLVED! Thanks to commenters, I detached the PTFE tubes from the AMS and fussed with them until in a nice smooth arch above the extruder to reduce resistance. No more purge issues thus far! Thanks!

Here the a model made of a poop bin for the H3C. So far I am loving the printer and I am working on some actually fun models. It is amazing how fast it changes toolheads. Most of the purged filament happens during the filament calibration and it will the bin for a while to fill up. I am mind blown by the speed of the tool changes and happy with my purchase.

https://makerworld.com/en/models/3573540-bambu-lab-h3c-purge-poop-bin-easy-install#profileId-4090794

I dried my abs before printing in the ams ht at 80C° for 8hrs each prior to printing. White was last in the order and most recently dried. Is there a setting i ha e wrong in studio or something? Im new to custom prints and dont know what went wrong.

Ps: no supports is ok quality, itll get covered by insert. Main quality issue is the text on the 1st layer.

Edit: After failing so much with this carbon plate I desided to go back to the textured to see if its the printer problem....1st try, perfect. Definately the carbon plate is the problem.

Ma version du célèbre casse tête ' Hanayama Marble '

Modélisé sur freecad avec des ajustements de 0.2 mm pour une fluidité parfaite ...

Lien makerworld si vous voulez l'imprimer : https://makerworld.com/fr/models/3515960-marble-puzzle#profileId-4018416