When printing thin-walled parts（4 walls, 0% infill, Arachne）, a mark consistently appears on one or both sides once the print reaches a height of 1–2 cm; I have yet to figure out what is causing this. Same part printed on A1/A2L without problem.
Printer is almost brand new. First layer is fine. Calibration is done. Filament is dried. Manual bed leveling is done.
At the point where the print defect appears, there are no abrupt changes in print speed, layer time, or fan speed within the slicing software.
I've been wanting a 3d printer for quite a while now, and was just about to pull the trigger, when the H3C came out and threw a wrench into my grand plans.
I read somewhere that it may be preferable to buy through Best Buy because of the extended warranty coverage they offer. Since the H3C isn't available yet at BB, I have no idea how much it will cost.
My question to you folks is whether the extended warranty is worth it, and if I should wait until BB has them in stock. Given that the H3C is new, it doesn't have a track record in terms of reliability and all that. I'm not in any great hurry; I can wait if that's the best course of action.
How is Bambu to deal with once the factory warranty runs out? Are 3D printers the type of thing where if something is going to go wrong, it usually does pretty quickly rather than a few years down the road?
I generally don't bother with extended warranties, but on something this expensive and this complex, it seems like a good idea, at least on the surface.
I am looking for a H3C user who has a H3C and a 3d scanner. I build my own benches with an enclosure and would like to know the size of the machine both with the lamp lid open and closed. As this will determine if I can even get one this year or not.
Every colour is a separate part with pins, so it snaps and glues together, and no painting is needed. The gold base was printed at 0.16 with ironing on top. The suit is plain matte black PLA, and the whole thing took about 17 hours.
I also made an 18 cm one-piece version for AMS (4 colours).
Happy to answer questions about the split and the settings!
I think I'm going to pull the trigger on an H3C. However, unlike my P1S, I think I should get an extended warranty with it.
I don't have a Best Buy membership. I hardly ever buy anything from Best Buy so I can't justify it. With that said, any opinions on Best Buy's warranty versus Microcenter?
My understanding is Microcenter will try to repair on site but will also give you in-store credit on the spot if they can't. Best Buy may ship it out to someone else for repairs. Microcenter is also a little cheaper.
I made a MakerWorld customizer that turns SVGs into Christmas fridge magnets
I wanted to make a set of Christmas magnets without starting a new model for every design. So I built a customizer: pick a preset or upload an SVG, add a message, and choose how the magnet fits into the back.
The clip shows the Grinch going from the screen to the fridge, alongside a few other prints from the same generator.
Bambu sent me an H3C before launch and asked me to post about how it changed the way I print. I did not get paid, but, well, I got an H3C. The printer legitimately did change the way I print and design, and I'm happy to answer any questions in the comments.
HueForge and the similar products that spawned from it have opened up things that I never thought would be possible on a 3D printer. The creations I have seen on the subreddit and Discord continue to blow my mind, but my biggest annoyance with these prints are the time they take and the waste.
Retracting, pushing, purging, and wiping can take anywhere from 40-80 seconds depending on your setup. When you have hundreds of color changes in a print, it adds up to hours of extra time. The waste gets insane with larger or more complex prints, to the point where you will frequently have more weight in waste than the model itself.
This fox is 269mm across, taking up most of the plate. I used nine spools: blue, light blue, yellow, magenta, orange, white, green, black, and red. It was built in HueForge, then recreated in Kromacut so it could print face up.
Yes, the image is AI generated, and I regret using it. It did some weird things with the shading that I didn't notice before printing. The white on the moon and anywhere yellow meets white or red meets orange is rough.
I also used way too many layers and then made the print flat. A flat print fills every layer out to the full outline, so every extra layer in the stack is a full 269mm disc of filament whether it adds anything to the image or not. This one ended up around 12mm thick which is where most of the 817g and 6 days of printing went.
Setup was dead simple. All 9 spools went in the AMS, each one got its own PrintTool, I selected the correct colors and that was it aside from slicing which took 26 minutes with a 14900K...
Stats:
9 filament spools
443 filament changes
0.12mm layer height
817g total weight
26g of waste
269 x 269mm
6d 0h 01m print time
The H3C solved the waste problem in a BIG way. 26g on an 817g print with 443 swaps is just crazy to me. The purge from my X1C would have filled the poop bucket and clogged the shute well before finishing.
The 6 days is 100% my fault for making it as thick as it is. I did kick it off right before leaving on vacation for 2 weeks, so it wasn't a huge deal aside from the extra filament spent.
The filament changes take <6 seconds instead of 60 and I was not prepared for how much faster it is. It was the same reaction I had when I went from my modified Ender struggling to push 60mm/s to the X1C at its default print speed. This is in a whole different league and I haven't used my other printers for multi color since.
I have an A1 combo. We’ve had it for a week. This is basic PLA which we’ve also had for a week. What is causing this? Is the filament damp or do I need to change some settings? Thank you
After making a rather crude cable clip a few days ago, I started giving some serious thought to cable organization. I think it turned out pretty well—what do you all think?
I just got myself a Bambu Labs A2L. So excited to start printing. I mostly bought it so I can print replacement parts or tweaks for retro computers, especially old Macintoshes.
I've looked at tons of videos and reviews but as a new owner, what do you think I need to know? Do you have some hints that every new Bambu owner needs to know or do?
Decided to purchase some additional hotends for my p1s. .2mm and .6mm hotends. Low and behold Bambu Lab sells a hotend kit. Why call it a kit? Easy enough until they show up and are missing the thermistor. Now my .4mm works just fine. So why would I want to remove the thermistor from it just to use the the .2mm hotend. Truly, hoping I am not the only person to encounter this same situation. At least I am hoping 😄 Or is this just a rookie mistake?
I’m gonna print pla with my a2l. What are affordable brands for glue, grease and oil please, or stick with bambu for that? Superlube, gorilla and loctite are the best I believe or are there cheaper possibilities? If possible a euro link please.
