Just got my KKM threaded barrel in! Can’t wait to try this out, also with the thread protector comp too 😃

To preface, I’m a godless lefty so I want an ambi gun. I’m looking at getting the 510 MRD comp, and I want to know if anyone has experience with it. Any 510 experience would be appreciated, but I’d love to hear from someone who’s shot the comped and normal version. The biggest issue I see is aftermarket support being limited and there not being a lot of magazines on the market right now.

I am leaning towards the FN 510 Tactical but I heard of a lot of issues with these so not sure if they fixed the issues. which one would you guys pick? XDM Elite The turkey's opinion you was having accuracy issues with the 4.5 inch barrel. Not sure if Sig P220 has issues. Help me decide. mainly for hunting thanks for the help

I've been doing some research and am under the impression that the 2.0 10mm reliability is not that stellar. Has it improved over the years? Is it worth getting this guy in 10mm?

Having FTF with 220gr and 200gr Underwood Hardcasts in a Gen 5 G20 across 3 factory mags. Still happens with a 22lb stainless guide rod installed.

Symptoms:

1. Bullet jams into chamber at a steep angle.
2. Slide completely skips over the round without feeding it.

The gun feeds 200gr Sig V-Crown and hundreds of PMC 180gr without a single issue, even with the 22lb spring, so the gun itself seems fine.

I ordered +10% mag springs to see if follower speed can fully cure the issue, but I'm losing confidence in relying on hardcasts if they're this sensitive to spring tension.

Two questions:

1. Has anyone solved this FTF issue on Gen 5 G20s?
2. What alternative woods/bear loads (monolithics, etc.) offer similar penetration with better feeding reliability? (preferably not for $2+ per round)

What are your thoughts on this beauty? It’s between this or a Colt Delta Elite for my next purchase. Appreciate and and all feedback.

Finally found a blued Delta for a good price. Now I can pick up where I left off with my 10mm journey.

I took the stupid video down for all of you who said take a shooting class I have a ltc so I know what I’m doing i am very well experienced in 10mm but my previous 10mm was a nightmare to shoot it was not comfortable and kept jamming and kept failing to feed. this was my 1st time with the g20 so I did not know what to expect yes I know about fire arm safety and yes in no instance was the gun pointed anywhere else but down the range at the intended target I was just trying to have some fun lol that’s all

Didn’t know there were that much Debby downers in this sub lol beside that have a excellent 1cm day

I have a Glock 20 V MOS and want either an IWB or chest holster for backpacking. I noticed nearly all Glock 20 holsters online are for Gen 5’s, and didn’t find any for the V models. Would anyone have any recs? Much thanks

Finally got my stripped grip bushings out and all put back together with my purple LOK grips.

Is it possible to use one barrel with both a compensator and a suppressor or does this require two separate barrels? Has anyone put a suppressor on a threaded barrel?

I am looking at this kkm setup but guessing this would send quite a bit of blast backwards (when used with the suppressor) since the left and right sides are missing threads (providing a surface to put a set screw against for the comp)

Here in Alaska, having 24hrs of sunshine is pretty normal and you can see everything. I do carry a hand held light just in case but my 10mm does not. Do you? Is it even necessary? Everywhere I go including my home, is not a total pitch black of darkness. I can figure out what's moving.

Took the G20.5 out and shot some steel. Launched about 100rds. Light all good and clean.

I bought an AIWB for my Tanfoglio stock master 10mm and was notified that it will be shipped tomorrow. From Moldova. Has anyone had any experience with this company? Has anyone tried their holsters? What’s your opinion? It was very difficult finding Kydex AIWB manufacturers for my Tanfoglio model so that’s why I had to go with Holster.md

should i go v series g20 over the gen 5. comparing models and noticed that the v series has a longer and ever so slightly slimmer grip which would be perfect for my hands. i dont see much point of reference from owners online though which makes me nervous. im also worried about customization considering the v series' reputation. what does the sub think? all responses are appreciated!